Jean Delvare [Sun, 7 Oct 2012 22:26:16 +0000 (09:26 +1100)]
i2c-i801: Let i2c-mux-gpio find the GPIO chip
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Jean Delvare [Sun, 7 Oct 2012 22:26:16 +0000 (09:26 +1100)]
i2c-mux-gpio: Add support for dynamically allocated GPIO pins
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Maxime Ripard [Sun, 7 Oct 2012 22:26:15 +0000 (09:26 +1100)]
i2c-mux-gpio: Use devm_kzalloc instead of kzalloc
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 7 Oct 2012 22:26:15 +0000 (09:26 +1100)]
i2c-i801: Support SMBus multiplexing on Asus Z8 series
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Peter Huewe [Sun, 7 Oct 2012 22:26:14 +0000 (09:26 +1100)]
i2c: Make I2C available on UML
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shubhrajyoti D [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c: Convert struct i2c_msg initialization to C99 format
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Julia Lawall [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c-smbus: Convert kzalloc to devm_kzalloc
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c-mux: Add support for device auto-detection
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: David Daney <david.daney@cavium.com> Cc: Michael Lawnick <ml.lawnick@gmx.de> Cc: Rodolfo Giometti <giometti@linux.it>
Linus Torvalds [Sun, 7 Oct 2012 22:14:06 +0000 (07:14 +0900)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
Linus Torvalds [Sun, 7 Oct 2012 21:38:18 +0000 (06:38 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph updates from Sage Weil:
"The bulk of this pull is a series from Alex that refactors and cleans
up the RBD code to lay the groundwork for supporting the new image
format and evolving feature set. There are also some cleanups in
libceph, and for ceph there's fixed validation of file striping
layouts and a bugfix in the code handling a shrinking MDS cluster."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: avoid 32-bit page index overflow
ceph: return EIO on invalid layout on GET_DATALOC ioctl
rbd: BUG on invalid layout
ceph: propagate layout error on osd request creation
libceph: check for invalid mapping
ceph: convert to use le32_add_cpu()
ceph: Fix oops when handling mdsmap that decreases max_mds
rbd: update remaining header fields for v2
rbd: get snapshot name for a v2 image
rbd: get the snapshot context for a v2 image
rbd: get image features for a v2 image
rbd: get the object prefix for a v2 rbd image
rbd: add code to get the size of a v2 rbd image
rbd: lay out header probe infrastructure
rbd: encapsulate code that gets snapshot info
rbd: add an rbd features field
rbd: don't use index in __rbd_add_snap_dev()
rbd: kill create_snap sysfs entry
rbd: define rbd_dev_image_id()
rbd: define some new format constants
...
Linus Torvalds [Sun, 7 Oct 2012 21:36:39 +0000 (06:36 +0900)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"The big new feature added this time is supporting online resizing
using the meta_bg feature. This allows us to resize file systems
which are greater than 16TB. In addition, the speed of online
resizing has been improved in general.
We also fix a number of races, some of which could lead to deadlocks,
in ext4's Asynchronous I/O and online defrag support, thanks to good
work by Dmitry Monakhov.
There are also a large number of more minor bug fixes and cleanups
from a number of other ext4 contributors, quite of few of which have
submitted fixes for the first time."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (69 commits)
ext4: fix ext4_flush_completed_IO wait semantics
ext4: fix mtime update in nodelalloc mode
ext4: fix ext_remove_space for punch_hole case
ext4: punch_hole should wait for DIO writers
ext4: serialize truncate with owerwrite DIO workers
ext4: endless truncate due to nonlocked dio readers
ext4: serialize unlocked dio reads with truncate
ext4: serialize dio nonlocked reads with defrag workers
ext4: completed_io locking cleanup
ext4: fix unwritten counter leakage
ext4: give i_aiodio_unwritten a more appropriate name
ext4: ext4_inode_info diet
ext4: convert to use leXX_add_cpu()
ext4: ext4_bread usage audit
fs: reserve fallocate flag codepoint
ext4: remove redundant offset check in mext_check_arguments()
ext4: don't clear orphan list on ro mount with errors
jbd2: fix assertion failure in commit code due to lacking transaction credits
ext4: release donor reference when EXT4_IOC_MOVE_EXT ioctl fails
ext4: enable FITRIM ioctl on bigalloc file system
...
Linus Torvalds [Sun, 7 Oct 2012 21:35:17 +0000 (06:35 +0900)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull i2c updates from Jean Delvare:
"Most visible changes are the SMBus multiplexing support added to the
i2c-i801 driver, as well as support for the VIA VX900."
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-piix4: Fix build failure
i2c: Correct struct i2c_driver doc about detection
i2c-i801: Let i2c-mux-gpio find the GPIO chip
i2c-mux-gpio: Update documentation
i2c-mux-gpio: Add support for dynamically allocated GPIO pins
i2c-mux-gpio: Use devm_kzalloc instead of kzalloc
i2c-i801: Support SMBus multiplexing on Asus Z8 series
i2c-viapro: Add VIA VX900 device ID
i2c-parport: i2c_parport_irq can be static
i2c-designware: i2c_dw_xfer_msg can be static
i2c/scx200_*: Replace printks with pr_<level>s
i2c: Make I2C available on UML
i2c: Convert struct i2c_msg initialization to C99 format
i2c-smbus: Convert kzalloc to devm_kzalloc
i2c-mux: Add support for device auto-detection
Linus Torvalds [Sun, 7 Oct 2012 21:33:44 +0000 (06:33 +0900)]
Merge tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for
that was already merged in the last release) and a debugfs interface
to export some statistics in the NVidia Tegra IOMMU driver."
* tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (27 commits)
iommu/amd: Remove obsolete comment line
dma-debug: Remove local BUS_NOTIFY_UNBOUND_DRIVER define
iommu/amd: Fix possible use after free in get_irq_table()
iommu/amd: Report irq remapping through IOMMU-API
iommu/amd: Print message to system log when irq remapping is enabled
iommu/irq: Use amd_iommu_irq_ops if supported
iommu/amd: Make sure irq remapping still works on dma init failure
iommu/amd: Add initialization routines for AMD interrupt remapping
iommu/amd: Add call-back routine for HPET MSI
iommu/amd: Implement MSI routines for interrupt remapping
iommu/amd: Add IOAPIC remapping routines
iommu/amd: Add routines to manage irq remapping tables
iommu/amd: Add IRTE invalidation routine
iommu/amd: Make sure IOMMU is not considered to translate itself
iommu/amd: Split device table initialization into irq and dma part
iommu/amd: Check if IOAPIC information is correct
iommu/amd: Allocate data structures to keep track of irq remapping tables
iommu/amd: Add slab-cache for irq remapping tables
iommu/amd: Keep track of HPET and IOAPIC device ids
iommu/amd: Fix features reporting
...
Eric Dumazet [Sat, 6 Oct 2012 22:28:06 +0000 (22:28 +0000)]
net: gro: fix a potential crash in skb_gro_reset_offset
Before accessing skb first fragment, better make sure there
is one.
This is probably not needed for old kernels, since an ethernet frame
cannot contain only an ethernet header, but the recent GRO addition
to tunnels makes this patch needed.
Also skb_gro_reset_offset() can be static, it actually allows
compiler to inline it.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 5 Oct 2012 20:43:30 +0000 (20:43 +0000)]
ipv6: GRO should be ECN friendly
IPv4 side of the problem was addressed in commit a9e050f4e7f9d
(net: tcp: GRO should be ECN friendly)
This patch does the same, but for IPv6 : A Traffic Class mismatch
doesnt mean flows are different, but instead should force a flush
of previous packets.
This patch removes artificial packet reordering problem.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix skb_under_panic oops in neigh_resolve_output
The retry loop in neigh_resolve_output() and neigh_connected_output()
call dev_hard_header() with out reseting the skb to network_header.
This causes the retry to fail with skb_under_panic. The fix is to
reset the network_header within the retry loop.
Signed-off-by: Ramesh Nagappa <ramesh.nagappa@ericsson.com> Reviewed-by: Shawn Lu <shawn.lu@ericsson.com> Reviewed-by: Robert Coulson <robert.coulson@ericsson.com> Reviewed-by: Billie Alsup <billie.alsup@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sky2_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_out*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function skge_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_led_off:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function gem_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_consistent:. For this error
case, the function abort its success execution path, but returns non
negative value, making it difficult for a caller function to notice
the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function niu_pci_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_res:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sh_eth_drv_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_release:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sonic_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function au1000_probe() return 0 for success and negative value
for most of its internal tests failures. There are exceptions
that are error cases going to err_out:. For this cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function amd8111e_probe_one() return 0 for success and negative
value for most of its internal tests failures. There are two exceptions
that are error cases going to err_free_reg:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function qlcnic_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_netdev:. For this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sh_sir_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_mem_*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sh_irda_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_mem_4:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sa1100_irda_probe() return 0 for success and negative
value for most of its internal tests failures. There is one exception
that is error case going to err_mem_4:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function pxa_irda_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_mem_3:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function mcs_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to error2:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function irtty_open() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_put:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function sis900_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_cleardev:. Fore this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function natsemi_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_create_file:. Fore this error case the
function abort its success execution path, but returns non negative value,
making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function dmfe_init_one() return 0 for success and negative value
for most of its internal tests failures. There are three exceptions
that are error cases going to err_out_*:. Fore this three cases the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 7 Oct 2012 12:20:57 +0000 (21:20 +0900)]
Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
Linus Torvalds [Sun, 7 Oct 2012 12:08:40 +0000 (21:08 +0900)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze arch updates from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
Revert "microblaze_mmu_v2: Update signal returning address"
microblaze: Added more support for PCI
microblaze: Prefer to use pr_XXX instead of printk(KERN_XX)
microblaze: Fix bug with passing command line
microblaze: Remove PAGE properties duplication
microblaze: Remove additional andi which has been already done
microblaze: Use predefined macro for ESR_DIZ
microblaze: Support 4k/16k/64k pages
microblaze: Do not used hardcoded value in exception handler
microblaze: Added fdt chosen capability for timer
microblaze: Add support for ioreadXX/iowriteXX_rep
microblaze: Improve failure handling for GPIO reset
microblaze: clinkage.h
Linus Torvalds [Sun, 7 Oct 2012 12:06:10 +0000 (21:06 +0900)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu arch updates from Greg Ungerer:
"Most of it is a cleanup of the ColdFire hardware header files. We
have had a few occurrances of bugs caused by inconsistent definitions
of peripheral addresses. These patches make them all consistent, and
also clean out a bunch of old crap. Overall we remove about 1000
lines."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (27 commits)
m68knommu: fix inconsistent formating in ColdFire 5407 definitions
m68knommu: fix inconsistent formating in ColdFire 5307 definitions
m68knommu: fix inconsistent formating in ColdFire 527x definitions
m68knommu: fix inconsistent formating in ColdFire 5272 definitions
m68knommu: fix inconsistent formating in ColdFire 523x definitions
m68knommu: clean up ColdFire 54xx General Timer definitions
m68knommu: clean up Pin Assignment definitions for the 54xx ColdFire CPU
m68knommu: fix multi-function pin setup for FEC module on ColdFire 523x
m68knommu: move ColdFire slice timer address defiens to 54xx header
m68knommu: use read/write IO access functions in ColdFire m532x setup code
m68knommu: modify ColdFire 532x GPIO register definitions to be consistent
m68knommu: remove a lot of unsed definitions for 532x ColdFire
m68knommu: use definitions for the ColdFire 528x FEC multi-function pins
m68knommu: remove address offsets relative to IPSBAR for ColdFire 527x
m68knommu: remove unused ColdFire 5282 register definitions
m68knommu: fix wrong register offsets used for ColdFire 5272 multi-function pins
m68knommu: make ColdFire 5249 MBAR2 register definitions absolute addresses
m68knommu: make remaining ColdFire 5272 register definitions absolute addresses
m68knommu: make ColdFire Park and Assignment register definitions absolute addresses
m68knommu: make ColdFire Chip Select register definitions absolute addresses
...
Linus Torvalds [Sun, 7 Oct 2012 12:04:56 +0000 (21:04 +0900)]
Merge branch 'virtio-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio changes from Rusty Russell:
"New workflow: same git trees pulled by linux-next get sent straight to
Linus. Git is awkward at shuffling patches compared with quilt or mq,
but that doesn't happen often once things get into my -next branch."
* 'virtio-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (24 commits)
lguest: fix occasional crash in example launcher.
virtio-blk: Disable callback in virtblk_done()
virtio_mmio: Don't attempt to create empty virtqueues
virtio_mmio: fix off by one error allocating queue
drivers/virtio/virtio_pci.c: fix error return code
virtio: don't crash when device is buggy
virtio: remove CONFIG_VIRTIO_RING
virtio: add help to CONFIG_VIRTIO option.
virtio: support reserved vqs
virtio: introduce an API to set affinity for a virtqueue
virtio-ring: move queue_index to vring_virtqueue
virtio_balloon: not EXPERIMENTAL any more.
virtio-balloon: dependency fix
virtio-blk: fix NULL checking in virtblk_alloc_req()
virtio-blk: Add REQ_FLUSH and REQ_FUA support to bio path
virtio-blk: Add bio-based IO path for virtio-blk
virtio: console: fix error handling in init() function
tools: Fix pthread flag for Makefile of trace-agent used by virtio-trace
tools: Add guest trace agent as a user tool
virtio/console: Allocate scatterlist according to the current pipe size
...
Linus Torvalds [Sun, 7 Oct 2012 11:55:16 +0000 (20:55 +0900)]
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
Linus Torvalds [Sun, 7 Oct 2012 11:49:16 +0000 (20:49 +0900)]
Merge tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc defconfig updates from Olof Johansson:
"This might be the last time we do a standalone defconfig branch, since
we now prefer to get them with the rest of the subarch updates
instead. These add a handful of useful options on various platforms,
enable new boards and SoCs, etc."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: defconfig updates
ARM: LPC32xx: Defconfig update
ARM: mach-shmobile: marzen: defconfig update
ARM: mxs_defconfig: Add SPI and LRADC support
ARM: s3c6400_defconfig: enable more boards in defconfig
ARM: imx_v6_v7_defconfig: Remove CONFIG_DEFAULT_MMAP_MIN_ADDR
ARM: imx_v6_v7_defconfig: Add Chipidea USB driver support
ARM: mxs_defconfig: Add framebuffer support
ARM: mxs_defconfig: Add LED, PWM and MTD_CHAR support
ARM: mxs_defconfig: Enable USB host
Linus Torvalds [Sun, 7 Oct 2012 08:49:05 +0000 (17:49 +0900)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
Linus Torvalds [Sun, 7 Oct 2012 08:30:50 +0000 (17:30 +0900)]
Merge tag 'for-v3.7' of git://git.infradead.org/users/cbou/linux-pstore
Pull pstore changes from Anton Vorontsov:
1) We no longer ad-hoc to the function tracer "high level"
infrastructure and no longer use its debugfs knobs. The change
slightly touches kernel/trace directory, but it got the needed ack
from Steven Rostedt:
http://lkml.org/lkml/2012/8/21/688
2) Added maintainers entry;
3) A bunch of fixes, nothing special.
* tag 'for-v3.7' of git://git.infradead.org/users/cbou/linux-pstore:
pstore: Avoid recursive spinlocks in the oops_in_progress case
pstore/ftrace: Convert to its own enable/disable debugfs knob
pstore/ram: Add missing platform_device_unregister
MAINTAINERS: Add pstore maintainers
pstore/ram: Mark ramoops_pstore_write_buf() as notrace
pstore/ram: Fix printk format warning
pstore/ram: Fix possible NULL dereference
Linus Torvalds [Sun, 7 Oct 2012 08:29:24 +0000 (17:29 +0900)]
Merge tag 'for-v3.7' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"1. New drivers:
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic,
and chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable
specific regulators;
5. Random fixes and cleanups for other drivers."
Fix up trivial conflicts in <linux/mfd/88pm860x.h>
* tag 'for-v3.7' of git://git.infradead.org/battery-2.6: (52 commits)
pda_power: Remove ac_draw_failed goto and label
charger-manager: Add support sysfs entry for charger
charger-manager: Support limit of maximum possible
charger-manager: Check fully charged state of battery periodically
lp8727_charger: More pure cosmetic improvements
lp8727_charger: Fix checkpatch warning
lp8727_charger: Add description in the private data
lp8727_charger: Fix a typo - chg_parm to chg_param
lp8727_charger: Make some cosmetic changes in lp8727_delayed_func()
lp8727_charger: Clean up lp8727_charger_changed()
lp8727_charger: Return if the battery is discharging
lp8727_charger: Make lp8727_charger_get_propery() simpler
lp8727_charger: Make lp8727_ctrl_switch() inline
lp8727_charger: Make lp8727_init_device() shorter
lp8727_charger: Clean up lp8727_is_charger_attached()
lp8727_charger: Use specific definition
lp8727_charger: Clean up lp8727 definitions
lp8727_charger: Use the definition rather than enum
lp8727_charger: Fix code for getting battery temp
lp8727_charger: Clear interrrupts at inital time
...
Linus Torvalds [Sun, 7 Oct 2012 08:19:49 +0000 (17:19 +0900)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband changes from Roland Dreier:
"Second batch of changes for the 3.7 merge window:
- Late-breaking fix for IPoIB on mlx4 SR-IOV VFs.
- Fix for IPoIB build breakage with CONFIG_INFINIBAND_IPOIB_CM=n (new
netlink config changes are to blame).
- Make sure retry count values are in range in RDMA CM.
- A few nes hardware driver fixes and cleanups.
- Have iSER initiator use >1 interrupt vectors if available."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Check that retry count values are in range
IB/iser: Add more RX CQs to scale out processing of SCSI responses
RDMA/nes: Bump the version number of nes driver
RDMA/nes: Remove unused module parameter "send_first"
RDMA/nes: Remove unnecessary if-else statement
RDMA/nes: Add missing break to switch.
mlx4_core: Adjust flow steering attach wrapper so that IB works on SR-IOV VFs
IPoIB: Fix build with CONFIG_INFINIBAND_IPOIB_CM=n
Eric Dumazet [Fri, 5 Oct 2012 06:23:55 +0000 (06:23 +0000)]
net: remove skb recycling
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit 87151b8689d (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao feng [Thu, 4 Oct 2012 20:15:49 +0000 (20:15 +0000)]
infiniband: pass rdma_cm module to netlink_dump_start
set netlink_dump_control.module to avoid panic.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Cc: Roland Dreier <roland@kernel.org> Cc: Sean Hefty <sean.hefty@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 6 Oct 2012 22:55:10 +0000 (07:55 +0900)]
Merge branch 'uapi-prep' of git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI disintegration fixes from David Howells:
"There are three main parts:
(1) I found I needed some more fixups in the wake of testing Arm64
(some asm/unistd.h files had weird guards that caused problems -
mostly in arches for which I don't have a compiler) and some
__KERNEL__ splitting needed to take place in Arm64.
(2) I found that c6x was missing some __KERNEL__ guards in its
asm/signal.h. Mark Salter pointed me at a tree with a patch to
remove that file entirely and use the asm-generic variant instead.
(3) Lastly, m68k turned out to have a header installation problem due
to it lacking a kvm_para.h file.
The conditional installation bits for linux/kvm_para.h, linux/kvm.h
and linux/a.out.h weren't very well specified - and didn't work if
an arch didn't have the asm/ version of that file, but there *was*
an asm-generic/ version.
It seems the "ifneq $((wildcard ...),)" for each of those three
headers in include/kernel/Kbuild is invoked twice during header
installation, and the second time it matches on the just installed
asm-generic/kvm_para.h file and thus incorrectly installs
linux/kvm_para.h as well.
Most arches actually have an asm/kvm_para.h, so this wasn't
detectable in those."
* 'uapi-prep' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Fix conditional header installation handling (notably kvm_para.h on m68k)
c6x: remove c6x signal.h
UAPI: Split compound conditionals containing __KERNEL__ in Arm64
UAPI: Fix the guards on various asm/unistd.h files
c6x: make dsk6455 the default config
Linus Torvalds [Sat, 6 Oct 2012 22:53:13 +0000 (07:53 +0900)]
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull SLAB changes from Pekka Enberg:
"New and noteworthy:
* More SLAB allocator unification patches from Christoph Lameter and
others. This paves the way for slab memcg patches that hopefully
will land in v3.8.
* SLAB tracing improvements from Ezequiel Garcia.
* Kernel tainting upon SLAB corruption from Dave Jones.
* Miscellanous SLAB allocator bug fixes and improvements from various
people."
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: (43 commits)
slab: Fix build failure in __kmem_cache_create()
slub: init_kmem_cache_cpus() and put_cpu_partial() can be static
mm/slab: Fix kmem_cache_alloc_node_trace() declaration
Revert "mm/slab: Fix kmem_cache_alloc_node_trace() declaration"
mm, slob: fix build breakage in __kmalloc_node_track_caller
mm/slab: Fix kmem_cache_alloc_node_trace() declaration
mm/slab: Fix typo _RET_IP -> _RET_IP_
mm, slub: Rename slab_alloc() -> slab_alloc_node() to match SLAB
mm, slab: Rename __cache_alloc() -> slab_alloc()
mm, slab: Match SLAB and SLUB kmem_cache_alloc_xxx_trace() prototype
mm, slab: Replace 'caller' type, void* -> unsigned long
mm, slob: Add support for kmalloc_track_caller()
mm, slab: Remove silly function slab_buffer_size()
mm, slob: Use NUMA_NO_NODE instead of -1
mm, sl[au]b: Taint kernel when we detect a corrupted slab
slab: Only define slab_error for DEBUG
slab: fix the DEADLOCK issue on l3 alien lock
slub: Zero initial memory segment for kmem_cache and kmem_cache_node
Revert "mm/sl[aou]b: Move sysfs_slab_add to common"
mm/sl[aou]b: Move kmem_cache refcounting to common code
...
Linus Torvalds [Sat, 6 Oct 2012 22:13:01 +0000 (07:13 +0900)]
Merge tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull ADM Xen support from Konrad Rzeszutek Wilk:
Features:
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions). PV
console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
The Xen-unstable hypervisor (so will be 4.3 in a ~6 months), supports
ARMv7 platforms.
The goal in implementing this architecture is to exploit the hardware
as much as possible. That means use as little as possible of PV
operations (so no PV MMU) - and use existing PV drivers for I/Os
(network, block, console, etc). This is similar to how PVHVM guests
operate in X86 platform nowadays - except that on ARM there is no need
for QEMU. The end result is that we share a lot of the generic Xen
drivers and infrastructure.
Details on how to compile/boot/etc are available at this Wiki:
* tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (21 commits)
xen/xen_initial_domain: check that xen_start_info is initialized
xen: mark xen_init_IRQ __init
xen/Makefile: fix dom-y build
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
...
Lance Ortiz [Tue, 2 Oct 2012 18:43:23 +0000 (12:43 -0600)]
ACPI: Add new sysfs interface to export device description
Add support to export the device description obtained from the ACPI _STR
method, if one exists for a device, to user-space via a sysfs interface.
This new interface provides a standard and platform neutral way for users
to obtain the description text stored in the ACPI _STR method. If no
_STR method exists for the device, no sysfs 'description' file will be
created. The 'description' file will be located in the /sys/devices/
directory using the device's path.
Execute the 'cat' command on the 'description' file to obtain the
description string for that device.
This patch also includes documentation describing how the new sysfs
interface works
Changes from v1-v2 based on comments by Len Brown and Fengguang Wu
* Removed output "No Description" and leaving a NULL attribute if the
_STR method failed to evaluate.
* In acpi_device_remove_files() removed the redundent check of
dev->pnp.str_obj before calling free. This check triggered a message
from smatch.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: Harden acpi_table_parse_entries() against BIOS bug
Parsing acpi table entries may fall into an infinite loop on a buggy BIOS
which has entry length=0 in acpi table.
Instead of kernel hang with few failure clue which leads to heavy lifting debug
effort, this patch hardens kernel boot by booting into non NUMA mode. The debug
info left in log buffer helps people identify the issue.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 6 Oct 2012 19:26:31 +0000 (15:26 -0400)]
tools/power/turbostat: add option to count SMIs, re-name some options
Counting SMIs is popular, so add a dedicated "-s" option to do it,
and juggle some of the other option letters.
-S is now system summary (was -s)
-c is 32 bit counter (was -d)
-C is 64-bit counter (was -D)
-p is 1st thread in core (was -c)
-P is 1st thread in package (was -p)
Jean Pihet [Thu, 20 Sep 2012 16:08:03 +0000 (18:08 +0200)]
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.
The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: Jean Pihet <j-pihet@ti.com> Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Thomas Kavanagh [Fri, 21 Sep 2012 03:20:46 +0000 (20:20 -0700)]
i2c: algo: pca: Fix chip reset function for PCA9665
The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.
Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net> Signed-off-by: Guenter Roeck <groeck@juniper.net> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
projects / karo-tx-linux.git / log