From 70692752af12e2dbae48685b1d07fe7bdb2fab31 Mon Sep 17 00:00:00 2001 From: Shawn Lin Date: Wed, 16 Sep 2015 14:41:37 +0800 Subject: [PATCH] mmc: dw_mmc: use macro for HCON register operations This patch add some macros for HCON register operations to make code more readable. Signed-off-by: Shawn Lin Signed-off-by: Jaehoon Chung Signed-off-by: Ulf Hansson --- drivers/mmc/host/dw_mmc.c | 6 +++--- drivers/mmc/host/dw_mmc.h | 3 +++ 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index 7fe0315142e6..6e600e875328 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -2669,7 +2669,7 @@ static void dw_mci_init_dma(struct dw_mci *host) * Check ADDR_CONFIG bit in HCON to find * IDMAC address bus width */ - addr_config = (mci_readl(host, HCON) >> 27) & 0x01; + addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON)); if (addr_config == 1) { /* host supports IDMAC in 64-bit address mode */ @@ -3046,7 +3046,7 @@ int dw_mci_probe(struct dw_mci *host) * Get the host data width - this assumes that HCON has been set with * the correct values. */ - i = (mci_readl(host, HCON) >> 7) & 0x7; + i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON)); if (!i) { host->push_data = dw_mci_push_data16; host->pull_data = dw_mci_pull_data16; @@ -3128,7 +3128,7 @@ int dw_mci_probe(struct dw_mci *host) if (host->pdata->num_slots) host->num_slots = host->pdata->num_slots; else - host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1; + host->num_slots = SDMMC_GET_SLOT_NUM(mci_readl(host, HCON)); /* * Enable interrupts for command done, data over, data empty, diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h index 811d4673a1c5..f2a88d4bcbac 100644 --- a/drivers/mmc/host/dw_mmc.h +++ b/drivers/mmc/host/dw_mmc.h @@ -154,6 +154,9 @@ #define DMA_INTERFACE_GDMA (0x2) #define DMA_INTERFACE_NODMA (0x3) #define SDMMC_GET_TRANS_MODE(x) (((x)>>16) & 0x3) +#define SDMMC_GET_SLOT_NUM(x) ((((x)>>1) & 0x1F) + 1) +#define SDMMC_GET_HDATA_WIDTH(x) (((x)>>7) & 0x7) +#define SDMMC_GET_ADDR_CONFIG(x) (((x)>>27) & 0x1) /* Internal DMAC interrupt defines */ #define SDMMC_IDMAC_INT_AI BIT(9) #define SDMMC_IDMAC_INT_NI BIT(8) -- 2.39.5