From c7c34af04998655c83db22de2b943cae27b942f7 Mon Sep 17 00:00:00 2001 From: Peter Meerwald Date: Thu, 17 May 2012 02:28:10 +0200 Subject: [PATCH] staging: iio: cleanup and move comments in hmc5843 Signed-off-by: Peter Meerwald Acked-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman --- drivers/staging/iio/magnetometer/hmc5843.c | 122 +++++++++++---------- 1 file changed, 63 insertions(+), 59 deletions(-) diff --git a/drivers/staging/iio/magnetometer/hmc5843.c b/drivers/staging/iio/magnetometer/hmc5843.c index d25b06ef8075..263cbcbff9ad 100644 --- a/drivers/staging/iio/magnetometer/hmc5843.c +++ b/drivers/staging/iio/magnetometer/hmc5843.c @@ -103,6 +103,18 @@ static const int hmc5843_regval_to_nanoscale[] = { 6173, 7692, 10309, 12821, 18868, 21739, 25641, 35714 }; +/* + * From the datasheet: + * Value | Sensor input field range (Ga) | Gain (counts/milli-Gauss) + * 0 | (+-)0.7 | 1620 + * 1 | (+-)1.0 | 1300 + * 2 | (+-)1.5 | 970 + * 3 | (+-)2.0 | 780 + * 4 | (+-)3.2 | 530 + * 5 | (+-)3.8 | 460 + * 6 | (+-)4.5 | 390 + * 7 | (+-)6.5 | 280 + */ static const int regval_to_input_field_mg[] = { 700, 1000, @@ -113,6 +125,19 @@ static const int regval_to_input_field_mg[] = { 4500, 6500 }; + +/* + * From the datasheet: + * Value | Data output rate (Hz) + * 0 | 0.5 + * 1 | 1 + * 2 | 2 + * 3 | 5 + * 4 | 10 (default) + * 5 | 20 + * 6 | 50 + * 7 | Not used + */ static const char * const regval_to_samp_freq[] = { "0.5", "1", @@ -130,18 +155,16 @@ static const unsigned short normal_i2c[] = { HMC5843_I2C_ADDRESS, /* Each client has this additional data */ struct hmc5843_data { struct mutex lock; - u8 rate; - u8 meas_conf; - u8 operating_mode; - u8 range; + u8 rate; + u8 meas_conf; + u8 operating_mode; + u8 range; }; -static void hmc5843_init_client(struct i2c_client *client); - +/* The lower two bits contain the current conversion mode */ static s32 hmc5843_configure(struct i2c_client *client, u8 operating_mode) { - /* The lower two bits contain the current conversion mode */ return i2c_smbus_write_byte_data(client, HMC5843_MODE_REG, operating_mode & HMC5843_MODE_MASK); @@ -166,23 +189,22 @@ static int hmc5843_read_measurement(struct iio_dev *indio_dev, if (result < 0) return -EINVAL; - *val = (s16)swab16((u16)result); + *val = (s16)swab16((u16)result); return IIO_VAL_INT; } - /* - * From the datasheet + * From the datasheet: * 0 - Continuous-Conversion Mode: In continuous-conversion mode, the - * device continuously performs conversions and places the result in the - * data register. + * device continuously performs conversions and places the result in + * the data register. * - * 1 - Single-Conversion Mode : device performs a single measurement, - * sets RDY high and returned to sleep mode + * 1 - Single-Conversion Mode : Device performs a single measurement, + * sets RDY high and returns to sleep mode. * - * 2 - Idle Mode : Device is placed in idle mode. + * 2 - Idle Mode : Device is placed in idle mode. * - * 3 - Sleep Mode. Device is placed in sleep mode. + * 3 - Sleep Mode : Device is placed in sleep mode. * */ static ssize_t hmc5843_show_operating_mode(struct device *dev, @@ -206,13 +228,14 @@ static ssize_t hmc5843_set_operating_mode(struct device *dev, unsigned long operating_mode = 0; s32 status; int error; + mutex_lock(&data->lock); error = kstrtoul(buf, 10, &operating_mode); if (error) { count = error; goto exit; } - dev_dbg(dev, "set Conversion mode to %lu\n", operating_mode); + dev_dbg(dev, "set conversion mode to %lu\n", operating_mode); if (operating_mode > HMC5843_MODE_SLEEP) { count = -EINVAL; goto exit; @@ -230,6 +253,7 @@ exit: mutex_unlock(&data->lock); return count; } + static IIO_DEVICE_ATTR(operating_mode, S_IWUSR | S_IRUGO, hmc5843_show_operating_mode, @@ -239,17 +263,19 @@ static IIO_DEVICE_ATTR(operating_mode, /* * API for setting the measurement configuration to * Normal, Positive bias and Negative bias - * From the datasheet * - * Normal measurement configuration (default): In normal measurement - * configuration the device follows normal measurement flow. Pins BP and BN - * are left floating and high impedance. + * From the datasheet: + * 0 - Normal measurement configuration (default): In normal measurement + * configuration the device follows normal measurement flow. Pins BP + * and BN are left floating and high impedance. * - * Positive bias configuration: In positive bias configuration, a positive - * current is forced across the resistive load on pins BP and BN. + * 1 - Positive bias configuration: In positive bias configuration, a + * positive current is forced across the resistive load on pins BP + * and BN. * - * Negative bias configuration. In negative bias configuration, a negative - * current is forced across the resistive load on pins BP and BN. + * 2 - Negative bias configuration. In negative bias configuration, a + * negative current is forced across the resistive load on pins BP + * and BN. * */ static s32 hmc5843_set_meas_conf(struct i2c_client *client, @@ -290,8 +316,7 @@ static ssize_t hmc5843_set_measurement_configuration(struct device *dev, return -EINVAL; mutex_lock(&data->lock); - - dev_dbg(dev, "set mode to %lu\n", meas_conf); + dev_dbg(dev, "set measurement configuration to %lu\n", meas_conf); if (hmc5843_set_meas_conf(client, meas_conf)) { count = -EINVAL; goto exit; @@ -302,25 +327,13 @@ exit: mutex_unlock(&data->lock); return count; } + static IIO_DEVICE_ATTR(meas_conf, S_IWUSR | S_IRUGO, hmc5843_show_measurement_configuration, hmc5843_set_measurement_configuration, 0); -/* - * From Datasheet - * The table shows the minimum data output - * Value | Minimum data output rate(Hz) - * 0 | 0.5 - * 1 | 1 - * 2 | 2 - * 3 | 5 - * 4 | 10 (default) - * 5 | 20 - * 6 | 50 - * 7 | Not used - */ static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("0.5 1 2 5 10 20 50"); static s32 hmc5843_set_rate(struct i2c_client *client, @@ -333,7 +346,7 @@ static s32 hmc5843_set_rate(struct i2c_client *client, reg_val = (data->meas_conf) | (rate << HMC5843_RATE_OFFSET); if (rate >= HMC5843_RATE_NOT_USED) { dev_err(&client->dev, - "This data output rate is not supported\n"); + "data output rate is not supported\n"); return -EINVAL; } return i2c_smbus_write_byte_data(client, HMC5843_CONFIG_REG_A, reg_val); @@ -392,31 +405,19 @@ static ssize_t show_sampling_frequency(struct device *dev, struct iio_dev_attr *this_attr = to_iio_dev_attr(attr); s32 rate; - rate = i2c_smbus_read_byte_data(client, this_attr->address); + rate = i2c_smbus_read_byte_data(client, this_attr->address); if (rate < 0) return rate; rate = (rate & HMC5843_RATE_BITMASK) >> HMC5843_RATE_OFFSET; return sprintf(buf, "%s\n", regval_to_samp_freq[rate]); } + static IIO_DEVICE_ATTR(sampling_frequency, S_IWUSR | S_IRUGO, show_sampling_frequency, set_sampling_frequency, HMC5843_CONFIG_REG_A); -/* - * From Datasheet - * Nominal gain settings - * Value | Sensor Input Field Range(Ga) | Gain(counts/ milli-gauss) - *0 |(+-)0.7 |1620 - *1 |(+-)1.0 |1300 - *2 |(+-)1.5 |970 - *3 |(+-)2.0 |780 - *4 |(+-)3.2 |530 - *5 |(+-)3.8 |460 - *6 |(+-)4.5 |390 - *7 |(+-)6.5 |280 - */ static ssize_t show_range(struct device *dev, struct device_attribute *attr, char *buf) @@ -440,6 +441,7 @@ static ssize_t set_range(struct device *dev, struct hmc5843_data *data = iio_priv(indio_dev); unsigned long range = 0; int error; + mutex_lock(&data->lock); error = kstrtoul(buf, 10, &range); if (error) { @@ -461,8 +463,8 @@ static ssize_t set_range(struct device *dev, exit: mutex_unlock(&data->lock); return count; - } + static IIO_DEVICE_ATTR(in_magn_range, S_IWUSR | S_IRUGO, show_range, @@ -537,7 +539,7 @@ static int hmc5843_detect(struct i2c_client *client, return 0; } -/* Called when we have found a new HMC5843. */ +/* Called when we have found a new HMC5843 */ static void hmc5843_init_client(struct i2c_client *client) { struct iio_dev *indio_dev = i2c_get_clientdata(client); @@ -548,6 +550,7 @@ static void hmc5843_init_client(struct i2c_client *client) hmc5843_configure(client, data->operating_mode); i2c_smbus_write_byte_data(client, HMC5843_CONFIG_REG_B, data->range); mutex_init(&data->lock); + pr_info("HMC5843 initialized\n"); } @@ -577,8 +580,6 @@ static int hmc5843_probe(struct i2c_client *client, data->operating_mode = HMC5843_MODE_CONVERSION_CONTINUOUS; i2c_set_clientdata(client, indio_dev); - - /* Initialize the HMC5843 chip */ hmc5843_init_client(client); indio_dev->info = &hmc5843_info; @@ -587,10 +588,13 @@ static int hmc5843_probe(struct i2c_client *client, indio_dev->num_channels = ARRAY_SIZE(hmc5843_channels); indio_dev->dev.parent = &client->dev; indio_dev->modes = INDIO_DIRECT_MODE; + err = iio_device_register(indio_dev); if (err) goto exit_free2; + return 0; + exit_free2: iio_device_free(indio_dev); exit: -- 2.39.5