From cc31a3c9aeedcb1330f34dbfccf6a979919d81f2 Mon Sep 17 00:00:00 2001 From: Arik Nemtsov Date: Thu, 12 Jul 2012 12:29:46 +0300 Subject: [PATCH] wl18xx: enable MIMO rates when connected as a MIMO STA Use this opportunity to consolidate the check for MIMO support into a separate function. Signed-off-by: Arik Nemtsov Signed-off-by: Luciano Coelho --- drivers/net/wireless/ti/wl18xx/main.c | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c index 2b9398c02a25..69042bb9a097 100644 --- a/drivers/net/wireless/ti/wl18xx/main.c +++ b/drivers/net/wireless/ti/wl18xx/main.c @@ -1013,6 +1013,13 @@ static void wl18xx_set_rx_csum(struct wl1271 *wl, skb->ip_summed = CHECKSUM_UNNECESSARY; } +static bool wl18xx_is_mimo_supported(struct wl1271 *wl) +{ + struct wl18xx_priv *priv = wl->priv; + + return priv->conf.phy.number_of_assembled_ant2_4 >= 2; +} + /* * TODO: instead of having these two functions to get the rate mask, * we should modify the wlvif->rate_set instead @@ -1029,6 +1036,9 @@ static u32 wl18xx_sta_get_ap_rate_mask(struct wl1271 *wl, /* we don't support MIMO in wide-channel mode */ hw_rate_set &= ~CONF_TX_MIMO_RATES; + } else if (wl18xx_is_mimo_supported(wl)) { + wl1271_debug(DEBUG_ACX, "using MIMO channel rate mask"); + hw_rate_set |= CONF_TX_MIMO_RATES; } return hw_rate_set; @@ -1037,8 +1047,6 @@ static u32 wl18xx_sta_get_ap_rate_mask(struct wl1271 *wl, static u32 wl18xx_ap_get_mimo_wide_rate_mask(struct wl1271 *wl, struct wl12xx_vif *wlvif) { - struct wl18xx_priv *priv = wl->priv; - if (wlvif->channel_type == NL80211_CHAN_HT40MINUS || wlvif->channel_type == NL80211_CHAN_HT40PLUS) { wl1271_debug(DEBUG_ACX, "using wide channel rate mask"); @@ -1048,7 +1056,7 @@ static u32 wl18xx_ap_get_mimo_wide_rate_mask(struct wl1271 *wl, return 0; return CONF_TX_RATE_USE_WIDE_CHAN; - } else if (priv->conf.phy.number_of_assembled_ant2_4 >= 2 && + } else if (wl18xx_is_mimo_supported(wl) && wlvif->band == IEEE80211_BAND_2GHZ) { wl1271_debug(DEBUG_ACX, "using MIMO rate mask"); /* @@ -1478,7 +1486,7 @@ static int __devinit wl18xx_probe(struct platform_device *pdev) * Only support mimo with multiple antennas. Fall back to * siso20. */ - if (priv->conf.phy.number_of_assembled_ant2_4 >= 2) + if (wl18xx_is_mimo_supported(wl)) wlcore_set_ht_cap(wl, IEEE80211_BAND_2GHZ, &wl18xx_mimo_ht_cap_2ghz); else -- 2.39.5