From dbef807ee890b45f9c9125b665c0dddc993c3d15 Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Wed, 20 Jun 2012 19:05:22 +0000 Subject: [PATCH] bnx2x: 1G sfp+ module handling Automatically lower requested link speed to 1G in case 1G SFP+ module is detected. Signed-off-by: Yuval Mintz Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- .../ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 16 +- .../net/ethernet/broadcom/bnx2x/bnx2x_link.c | 202 +++++++++++------- .../net/ethernet/broadcom/bnx2x/bnx2x_link.h | 17 +- 3 files changed, 151 insertions(+), 84 deletions(-) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c index 70c0881ce5a0..819170ee152a 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c @@ -187,7 +187,8 @@ static int bnx2x_get_port_type(struct bnx2x *bp) int port_type; u32 phy_idx = bnx2x_get_cur_phy_idx(bp); switch (bp->link_params.phy[phy_idx].media_type) { - case ETH_PHY_SFP_FIBER: + case ETH_PHY_SFPP_10G_FIBER: + case ETH_PHY_SFP_1G_FIBER: case ETH_PHY_XFP_FIBER: case ETH_PHY_KR: case ETH_PHY_CX4: @@ -220,6 +221,11 @@ static int bnx2x_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) (bp->port.supported[cfg_idx ^ 1] & (SUPPORTED_TP | SUPPORTED_FIBRE)); cmd->advertising = bp->port.advertising[cfg_idx]; + if (bp->link_params.phy[bnx2x_get_cur_phy_idx(bp)].media_type == + ETH_PHY_SFP_1G_FIBER) { + cmd->supported &= ~(SUPPORTED_10000baseT_Full); + cmd->advertising &= ~(ADVERTISED_10000baseT_Full); + } if ((bp->state == BNX2X_STATE_OPEN) && (bp->link_vars.link_up)) { if (!(bp->flags & MF_FUNC_DIS)) { @@ -295,7 +301,7 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) { struct bnx2x *bp = netdev_priv(dev); u32 advertising, cfg_idx, old_multi_phy_config, new_multi_phy_config; - u32 speed; + u32 speed, phy_idx; if (IS_MF_SD(bp)) return 0; @@ -550,9 +556,11 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) "10G half not supported\n"); return -EINVAL; } - + phy_idx = bnx2x_get_cur_phy_idx(bp); if (!(bp->port.supported[cfg_idx] - & SUPPORTED_10000baseT_Full)) { + & SUPPORTED_10000baseT_Full) || + (bp->link_params.phy[phy_idx].media_type == + ETH_PHY_SFP_1G_FIBER)) { DP(BNX2X_MSG_ETHTOOL, "10G full not supported\n"); return -EINVAL; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index 23ca0b642a8e..b21a6be81032 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -4373,6 +4373,23 @@ static void bnx2x_warpcore_config_runtime(struct bnx2x_phy *phy, } /*params->rx_tx_asic_rst*/ } +static void bnx2x_warpcore_config_sfi(struct bnx2x_phy *phy, + struct link_params *params) +{ + u16 lane = bnx2x_get_warpcore_lane(phy, params); + struct bnx2x *bp = params->bp; + bnx2x_warpcore_clear_regs(phy, params, lane); + if ((params->req_line_speed[LINK_CONFIG_IDX(INT_PHY)] == + SPEED_10000) && + (phy->media_type != ETH_PHY_SFP_1G_FIBER)) { + DP(NETIF_MSG_LINK, "Setting 10G SFI\n"); + bnx2x_warpcore_set_10G_XFI(phy, params, 0); + } else { + DP(NETIF_MSG_LINK, "Setting 1G Fiber\n"); + bnx2x_warpcore_set_sgmii_speed(phy, params, 1, 0); + } +} + static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars) @@ -4433,19 +4450,11 @@ static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy, break; case PORT_HW_CFG_NET_SERDES_IF_SFI: - - bnx2x_warpcore_clear_regs(phy, params, lane); - if (vars->line_speed == SPEED_10000) { - DP(NETIF_MSG_LINK, "Setting 10G SFI\n"); - bnx2x_warpcore_set_10G_XFI(phy, params, 0); - } else if (vars->line_speed == SPEED_1000) { - DP(NETIF_MSG_LINK, "Setting 1G Fiber\n"); - bnx2x_warpcore_set_sgmii_speed( - phy, params, 1, 0); - } /* Issue Module detection */ if (bnx2x_is_sfp_module_plugged(phy, params)) bnx2x_sfp_module_detection(phy, params); + + bnx2x_warpcore_config_sfi(phy, params); break; case PORT_HW_CFG_NET_SERDES_IF_DXGXS: @@ -6354,7 +6363,9 @@ int bnx2x_test_link(struct link_params *params, struct link_vars *vars, for (phy_index = EXT_PHY1; phy_index < params->num_phys; phy_index++) { serdes_phy_type = ((params->phy[phy_index].media_type == - ETH_PHY_SFP_FIBER) || + ETH_PHY_SFPP_10G_FIBER) || + (params->phy[phy_index].media_type == + ETH_PHY_SFP_1G_FIBER) || (params->phy[phy_index].media_type == ETH_PHY_XFP_FIBER) || (params->phy[phy_index].media_type == @@ -7891,7 +7902,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u32 sync_offset = 0, phy_idx, media_types; - u8 val, check_limiting_mode = 0; + u8 val[2], check_limiting_mode = 0; *edc_mode = EDC_MODE_LIMITING; phy->media_type = ETH_PHY_UNSPECIFIED; @@ -7899,13 +7910,13 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, if (bnx2x_read_sfp_module_eeprom(phy, params, SFP_EEPROM_CON_TYPE_ADDR, - 1, - &val) != 0) { + 2, + (u8 *)val) != 0) { DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n"); return -EINVAL; } - switch (val) { + switch (val[0]) { case SFP_EEPROM_CON_TYPE_VAL_COPPER: { u8 copper_module_type; @@ -7943,13 +7954,29 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, break; } case SFP_EEPROM_CON_TYPE_VAL_LC: - phy->media_type = ETH_PHY_SFP_FIBER; - DP(NETIF_MSG_LINK, "Optic module detected\n"); check_limiting_mode = 1; + if ((val[1] & (SFP_EEPROM_COMP_CODE_SR_MASK | + SFP_EEPROM_COMP_CODE_LR_MASK | + SFP_EEPROM_COMP_CODE_LRM_MASK)) == 0) { + DP(NETIF_MSG_LINK, "1G Optic module detected\n"); + phy->media_type = ETH_PHY_SFP_1G_FIBER; + phy->req_line_speed = SPEED_1000; + } else { + int idx, cfg_idx = 0; + DP(NETIF_MSG_LINK, "10G Optic module detected\n"); + for (idx = INT_PHY; idx < MAX_PHYS; idx++) { + if (params->phy[idx].type == phy->type) { + cfg_idx = LINK_CONFIG_IDX(idx); + break; + } + } + phy->media_type = ETH_PHY_SFPP_10G_FIBER; + phy->req_line_speed = params->req_line_speed[cfg_idx]; + } break; default: DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n", - val); + val[0]); return -EINVAL; } sync_offset = params->shmem_base + @@ -8479,14 +8506,34 @@ void bnx2x_handle_module_detect_int(struct link_params *params) /* Call the handling function in case module is detected */ if (gpio_val == 0) { + bnx2x_set_mdio_clk(bp, params->chip_id, params->port); + bnx2x_set_aer_mmd(params, phy); + bnx2x_power_sfp_module(params, phy, 1); bnx2x_set_gpio_int(bp, gpio_num, MISC_REGISTERS_GPIO_INT_OUTPUT_CLR, gpio_port); - if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) + if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) { bnx2x_sfp_module_detection(phy, params); - else + if (CHIP_IS_E3(bp)) { + u16 rx_tx_in_reset; + /* In case WC is out of reset, reconfigure the + * link speed while taking into account 1G + * module limitation. + */ + bnx2x_cl45_read(bp, phy, + MDIO_WC_DEVAD, + MDIO_WC_REG_DIGITAL5_MISC6, + &rx_tx_in_reset); + if (!rx_tx_in_reset) { + bnx2x_warpcore_reset_lane(bp, phy, 1); + bnx2x_warpcore_config_sfi(phy, params); + bnx2x_warpcore_reset_lane(bp, phy, 0); + } + } + } else { DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); + } } else { u32 val = REG_RD(bp, params->shmem_base + offsetof(struct shmem_region, dev_info. @@ -8938,6 +8985,63 @@ static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy, MISC_REGISTERS_GPIO_OUTPUT_LOW, port); } +static void bnx2x_8727_config_speed(struct bnx2x_phy *phy, + struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 tmp1, val; + /* Set option 1G speed */ + if ((phy->req_line_speed == SPEED_1000) || + (phy->media_type == ETH_PHY_SFP_1G_FIBER)) { + DP(NETIF_MSG_LINK, "Setting 1G force\n"); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD); + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1); + DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1); + /* Power down the XAUI until link is up in case of dual-media + * and 1G + */ + if (DUAL_MEDIA(params)) { + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_GP, &val); + val |= (3<<10); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_GP, val); + } + } else if ((phy->req_line_speed == SPEED_AUTO_NEG) && + ((phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) && + ((phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) != + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { + + DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); + bnx2x_cl45_write(bp, phy, + MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0); + bnx2x_cl45_write(bp, phy, + MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300); + } else { + /* Since the 8727 has only single reset pin, need to set the 10G + * registers although it is default + */ + bnx2x_cl45_write(bp, phy, + MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, + 0x0020); + bnx2x_cl45_write(bp, phy, + MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, + 0x0008); + } +} + static int bnx2x_8727_config_init(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars) @@ -9007,56 +9111,7 @@ static int bnx2x_8727_config_init(struct bnx2x_phy *phy, bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1); - /* Set option 1G speed */ - if (phy->req_line_speed == SPEED_1000) { - DP(NETIF_MSG_LINK, "Setting 1G force\n"); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD); - bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1); - DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1); - /* Power down the XAUI until link is up in case of dual-media - * and 1G - */ - if (DUAL_MEDIA(params)) { - bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8727_PCS_GP, &val); - val |= (3<<10); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8727_PCS_GP, val); - } - } else if ((phy->req_line_speed == SPEED_AUTO_NEG) && - ((phy->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) && - ((phy->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) != - PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { - - DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); - bnx2x_cl45_write(bp, phy, - MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0); - bnx2x_cl45_write(bp, phy, - MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300); - } else { - /* Since the 8727 has only single reset pin, need to set the 10G - * registers although it is default - */ - bnx2x_cl45_write(bp, phy, - MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, - 0x0020); - bnx2x_cl45_write(bp, phy, - MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, - 0x0008); - } - + bnx2x_8727_config_speed(phy, params); /* Set 2-wire transfer rate of SFP+ module EEPROM * to 100Khz since some DACs(direct attached cables) do * not work at 400Khz. @@ -9183,6 +9238,9 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, bnx2x_sfp_module_detection(phy, params); else DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); + + /* Reconfigure link speed based on module type limitations */ + bnx2x_8727_config_speed(phy, params); } DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", @@ -11327,7 +11385,7 @@ static struct bnx2x_phy phy_8706 = { SUPPORTED_FIBRE | SUPPORTED_Pause | SUPPORTED_Asym_Pause), - .media_type = ETH_PHY_SFP_FIBER, + .media_type = ETH_PHY_SFPP_10G_FIBER, .ver_addr = 0, .req_flow_ctrl = 0, .req_line_speed = 0, @@ -11666,7 +11724,7 @@ static int bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port, SUPPORTED_FIBRE | SUPPORTED_Pause | SUPPORTED_Asym_Pause); - phy->media_type = ETH_PHY_SFP_FIBER; + phy->media_type = ETH_PHY_SFPP_10G_FIBER; break; case PORT_HW_CFG_NET_SERDES_IF_KR: phy->media_type = ETH_PHY_KR; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h index 7b6051bc4551..017236bee323 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h @@ -168,14 +168,15 @@ struct bnx2x_phy { u32 supported; u32 media_type; -#define ETH_PHY_UNSPECIFIED 0x0 -#define ETH_PHY_SFP_FIBER 0x1 -#define ETH_PHY_XFP_FIBER 0x2 -#define ETH_PHY_DA_TWINAX 0x3 -#define ETH_PHY_BASE_T 0x4 -#define ETH_PHY_KR 0xf0 -#define ETH_PHY_CX4 0xf1 -#define ETH_PHY_NOT_PRESENT 0xff +#define ETH_PHY_UNSPECIFIED 0x0 +#define ETH_PHY_SFPP_10G_FIBER 0x1 +#define ETH_PHY_XFP_FIBER 0x2 +#define ETH_PHY_DA_TWINAX 0x3 +#define ETH_PHY_BASE_T 0x4 +#define ETH_PHY_SFP_1G_FIBER 0x5 +#define ETH_PHY_KR 0xf0 +#define ETH_PHY_CX4 0xf1 +#define ETH_PHY_NOT_PRESENT 0xff /* The address in which version is located*/ u32 ver_addr; -- 2.39.5