From e7a932b1961c3936c7ae5b8d1628f39dc50a746d Mon Sep 17 00:00:00 2001 From: Joseph Lo Date: Mon, 12 Aug 2013 17:40:04 +0800 Subject: [PATCH] ARM: tegra: add LP1 suspend support for Tegra30 The LP1 suspend mode will power off the CPU, clock gated the PLLs and put SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The sequence when LP1 suspending: * tunning off L1 data cache and the MMU * storing some EMC registers, DPD (deep power down) status, clk source of mselect and SCLK burst policy * putting SDRAM into self-refresh * switching CPU to CLK_M (12MHz OSC) * tunning off PLLM, PLLP, PLLA, PLLC and PLLX * switching SCLK to CLK_S (32KHz OSC) * shutting off the CPU rail The sequence of LP1 resuming: * re-enabling PLLM, PLLP, PLLA, PLLC and PLLX * restoring the clk source of mselect and SCLK burst policy * setting up CCLK burst policy to PLLX * restoring DPD status and some EMC registers * resuming SDRAM to normal mode * jumping to the "tegra_resume" from PMC_SCRATCH41 Due to the SDRAM will be put into self-refresh mode, the low level procedures of LP1 suspending and resuming should be copied to TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before restoring the CPU context when resuming, the SDRAM needs to be switched back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy be restored, CCLK burst policy be set in PLLX. Then jumping to "tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore CPU context and back to kernel. Based on the work by: Scott Williams Signed-off-by: Joseph Lo Signed-off-by: Stephen Warren --- arch/arm/mach-tegra/Makefile | 1 + arch/arm/mach-tegra/pm-tegra30.c | 34 ++ arch/arm/mach-tegra/pm.c | 18 + arch/arm/mach-tegra/pm.h | 3 + arch/arm/mach-tegra/sleep-tegra30.S | 492 ++++++++++++++++++++++++++++ arch/arm/mach-tegra/sleep.S | 8 +- arch/arm/mach-tegra/sleep.h | 8 + 7 files changed, 560 insertions(+), 4 deletions(-) create mode 100644 arch/arm/mach-tegra/pm-tegra30.c diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile index 98b184efc110..d341980d5ca9 100644 --- a/arch/arm/mach-tegra/Makefile +++ b/arch/arm/mach-tegra/Makefile @@ -22,6 +22,7 @@ obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += cpuidle-tegra20.o endif obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra30_speedo.o obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += sleep-tegra30.o +obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += pm-tegra30.o ifeq ($(CONFIG_CPU_IDLE),y) obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += cpuidle-tegra30.o endif diff --git a/arch/arm/mach-tegra/pm-tegra30.c b/arch/arm/mach-tegra/pm-tegra30.c new file mode 100644 index 000000000000..8fa326d6ff1a --- /dev/null +++ b/arch/arm/mach-tegra/pm-tegra30.c @@ -0,0 +1,34 @@ +/* + * Copyright (c) 2013, NVIDIA Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ +#include + +#include "pm.h" + +#ifdef CONFIG_PM_SLEEP +extern u32 tegra30_iram_start, tegra30_iram_end; +extern void tegra30_sleep_core_finish(unsigned long); + +void tegra30_lp1_iram_hook(void) +{ + tegra_lp1_iram.start_addr = &tegra30_iram_start; + tegra_lp1_iram.end_addr = &tegra30_iram_end; +} + +void tegra30_sleep_core_init(void) +{ + tegra_sleep_core_finish = tegra30_sleep_core_finish; +} +#endif diff --git a/arch/arm/mach-tegra/pm.c b/arch/arm/mach-tegra/pm.c index 10689924a6a7..7739d5586cb7 100644 --- a/arch/arm/mach-tegra/pm.c +++ b/arch/arm/mach-tegra/pm.c @@ -209,6 +209,15 @@ static int tegra_sleep_core(unsigned long v2p) */ static bool tegra_lp1_iram_hook(void) { + switch (tegra_chip_id) { + case TEGRA30: + if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC)) + tegra30_lp1_iram_hook(); + break; + default: + break; + } + if (!tegra_lp1_iram.start_addr || !tegra_lp1_iram.end_addr) return false; @@ -222,6 +231,15 @@ static bool tegra_lp1_iram_hook(void) static bool tegra_sleep_core_init(void) { + switch (tegra_chip_id) { + case TEGRA30: + if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC)) + tegra30_sleep_core_init(); + break; + default: + break; + } + if (!tegra_sleep_core_finish) return false; diff --git a/arch/arm/mach-tegra/pm.h b/arch/arm/mach-tegra/pm.h index 478706edebbe..803bd5382257 100644 --- a/arch/arm/mach-tegra/pm.h +++ b/arch/arm/mach-tegra/pm.h @@ -30,6 +30,9 @@ struct tegra_lp1_iram { extern struct tegra_lp1_iram tegra_lp1_iram; extern void (*tegra_sleep_core_finish)(unsigned long v2p); +void tegra30_lp1_iram_hook(void); +void tegra30_sleep_core_init(void); + extern unsigned long l2x0_saved_regs_addr; void save_cpu_arch_register(void); diff --git a/arch/arm/mach-tegra/sleep-tegra30.S b/arch/arm/mach-tegra/sleep-tegra30.S index ecad4eace941..2be7f70e19cb 100644 --- a/arch/arm/mach-tegra/sleep-tegra30.S +++ b/arch/arm/mach-tegra/sleep-tegra30.S @@ -18,13 +18,102 @@ #include #include +#include #include "fuse.h" #include "sleep.h" #include "flowctrl.h" +#define EMC_CFG 0xc +#define EMC_ADR_CFG 0x10 +#define EMC_TIMING_CONTROL 0x28 +#define EMC_REFRESH 0x70 +#define EMC_NOP 0xdc +#define EMC_SELF_REF 0xe0 +#define EMC_MRW 0xe8 +#define EMC_FBIO_CFG5 0x104 +#define EMC_AUTO_CAL_CONFIG 0x2a4 +#define EMC_AUTO_CAL_INTERVAL 0x2a8 +#define EMC_AUTO_CAL_STATUS 0x2ac +#define EMC_REQ_CTRL 0x2b0 +#define EMC_CFG_DIG_DLL 0x2bc +#define EMC_EMC_STATUS 0x2b4 +#define EMC_ZCAL_INTERVAL 0x2e0 +#define EMC_ZQ_CAL 0x2ec +#define EMC_XM2VTTGENPADCTRL 0x310 +#define EMC_XM2VTTGENPADCTRL2 0x314 + +#define PMC_CTRL 0x0 +#define PMC_CTRL_SIDE_EFFECT_LP0 (1 << 14) /* enter LP0 when CPU pwr gated */ + +#define PMC_PLLP_WB0_OVERRIDE 0xf8 +#define PMC_IO_DPD_REQ 0x1b8 +#define PMC_IO_DPD_STATUS 0x1bc + +#define CLK_RESET_CCLK_BURST 0x20 +#define CLK_RESET_CCLK_DIVIDER 0x24 +#define CLK_RESET_SCLK_BURST 0x28 +#define CLK_RESET_SCLK_DIVIDER 0x2c + +#define CLK_RESET_PLLC_BASE 0x80 +#define CLK_RESET_PLLC_MISC 0x8c +#define CLK_RESET_PLLM_BASE 0x90 +#define CLK_RESET_PLLM_MISC 0x9c +#define CLK_RESET_PLLP_BASE 0xa0 +#define CLK_RESET_PLLP_MISC 0xac +#define CLK_RESET_PLLA_BASE 0xb0 +#define CLK_RESET_PLLA_MISC 0xbc +#define CLK_RESET_PLLX_BASE 0xe0 +#define CLK_RESET_PLLX_MISC 0xe4 + +#define CLK_RESET_CLK_SOURCE_MSELECT 0x3b4 + +#define MSELECT_CLKM (0x3 << 30) + +#define LOCK_DELAY 50 /* safety delay after lock is detected */ + #define TEGRA30_POWER_HOTPLUG_SHUTDOWN (1 << 27) /* Hotplug shutdown */ +.macro emc_device_mask, rd, base + ldr \rd, [\base, #EMC_ADR_CFG] + tst \rd, #0x1 + moveq \rd, #(0x1 << 8) @ just 1 device + movne \rd, #(0x3 << 8) @ 2 devices +.endm + +.macro emc_timing_update, rd, base + mov \rd, #1 + str \rd, [\base, #EMC_TIMING_CONTROL] +1001: + ldr \rd, [\base, #EMC_EMC_STATUS] + tst \rd, #(0x1<<23) @ wait EMC_STATUS_TIMING_UPDATE_STALLED is clear + bne 1001b +.endm + +.macro pll_enable, rd, r_car_base, pll_base, pll_misc + ldr \rd, [\r_car_base, #\pll_base] + tst \rd, #(1 << 30) + orreq \rd, \rd, #(1 << 30) + streq \rd, [\r_car_base, #\pll_base] + /* Enable lock detector */ + .if \pll_misc + ldr \rd, [\r_car_base, #\pll_misc] + bic \rd, \rd, #(1 << 18) + str \rd, [\r_car_base, #\pll_misc] + ldr \rd, [\r_car_base, #\pll_misc] + ldr \rd, [\r_car_base, #\pll_misc] + orr \rd, \rd, #(1 << 18) + str \rd, [\r_car_base, #\pll_misc] + .endif +.endm + +.macro pll_locked, rd, r_car_base, pll_base +1: + ldr \rd, [\r_car_base, #\pll_base] + tst \rd, #(1 << 27) + beq 1b +.endm + #if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_PM_SLEEP) /* * tegra30_hotplug_shutdown(void) @@ -128,6 +217,41 @@ ENDPROC(tegra30_cpu_shutdown) #endif #ifdef CONFIG_PM_SLEEP +/* + * tegra30_sleep_core_finish(unsigned long v2p) + * + * Enters suspend in LP0 or LP1 by turning off the MMU and jumping to + * tegra30_tear_down_core in IRAM + */ +ENTRY(tegra30_sleep_core_finish) + /* Flush, disable the L1 data cache and exit SMP */ + bl tegra_disable_clean_inv_dcache + + /* + * Preload all the address literals that are needed for the + * CPU power-gating process, to avoid loading from SDRAM which + * are not supported once SDRAM is put into self-refresh. + * LP0 / LP1 use physical address, since the MMU needs to be + * disabled before putting SDRAM into self-refresh to avoid + * memory access due to page table walks. + */ + mov32 r4, TEGRA_PMC_BASE + mov32 r5, TEGRA_CLK_RESET_BASE + mov32 r6, TEGRA_FLOW_CTRL_BASE + mov32 r7, TEGRA_TMRUS_BASE + + mov32 r3, tegra_shut_off_mmu + add r3, r3, r0 + + mov32 r0, tegra30_tear_down_core + mov32 r1, tegra30_iram_start + sub r0, r0, r1 + mov32 r1, TEGRA_IRAM_CODE_AREA + add r0, r0, r1 + + mov pc, r3 +ENDPROC(tegra30_sleep_core_finish) + /* * tegra30_sleep_cpu_secondary_finish(unsigned long v2p) * @@ -158,6 +282,273 @@ ENTRY(tegra30_tear_down_cpu) b tegra30_enter_sleep ENDPROC(tegra30_tear_down_cpu) +/* START OF ROUTINES COPIED TO IRAM */ + .align L1_CACHE_SHIFT + .globl tegra30_iram_start +tegra30_iram_start: + +/* + * tegra30_lp1_reset + * + * reset vector for LP1 restore; copied into IRAM during suspend. + * Brings the system back up to a safe staring point (SDRAM out of + * self-refresh, PLLC, PLLM and PLLP reenabled, CPU running on PLLX, + * system clock running on the same PLL that it suspended at), and + * jumps to tegra_resume to restore virtual addressing. + * The physical address of tegra_resume expected to be stored in + * PMC_SCRATCH41. + * + * NOTE: THIS *MUST* BE RELOCATED TO TEGRA_IRAM_CODE_AREA. + */ +ENTRY(tegra30_lp1_reset) + /* + * The CPU and system bus are running at 32KHz and executing from + * IRAM when this code is executed; immediately switch to CLKM and + * enable PLLP, PLLM, PLLC, PLLA and PLLX. + */ + mov32 r0, TEGRA_CLK_RESET_BASE + + mov r1, #(1 << 28) + str r1, [r0, #CLK_RESET_SCLK_BURST] + str r1, [r0, #CLK_RESET_CCLK_BURST] + mov r1, #0 + str r1, [r0, #CLK_RESET_CCLK_DIVIDER] + str r1, [r0, #CLK_RESET_SCLK_DIVIDER] + + /* enable PLLM via PMC */ + mov32 r2, TEGRA_PMC_BASE + ldr r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + orr r1, r1, #(1 << 12) + str r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + + pll_enable r1, r0, CLK_RESET_PLLM_BASE, CLK_RESET_PLLM_MISC + pll_enable r1, r0, CLK_RESET_PLLP_BASE, CLK_RESET_PLLP_MISC + pll_enable r1, r0, CLK_RESET_PLLA_BASE, CLK_RESET_PLLA_MISC + pll_enable r1, r0, CLK_RESET_PLLC_BASE, CLK_RESET_PLLC_MISC + pll_enable r1, r0, CLK_RESET_PLLX_BASE, CLK_RESET_PLLX_MISC + + pll_locked r1, r0, CLK_RESET_PLLM_BASE + pll_locked r1, r0, CLK_RESET_PLLP_BASE + pll_locked r1, r0, CLK_RESET_PLLA_BASE + pll_locked r1, r0, CLK_RESET_PLLC_BASE + pll_locked r1, r0, CLK_RESET_PLLX_BASE + + mov32 r7, TEGRA_TMRUS_BASE + ldr r1, [r7] + add r1, r1, #LOCK_DELAY + wait_until r1, r7, r3 + + adr r5, tegra30_sdram_pad_save + + ldr r4, [r5, #0x18] @ restore CLK_SOURCE_MSELECT + str r4, [r0, #CLK_RESET_CLK_SOURCE_MSELECT] + + ldr r4, [r5, #0x1C] @ restore SCLK_BURST + str r4, [r0, #CLK_RESET_SCLK_BURST] + + mov32 r4, ((1 << 28) | (0x8)) @ burst policy is PLLX + str r4, [r0, #CLK_RESET_CCLK_BURST] + + /* Restore pad power state to normal */ + ldr r1, [r5, #0x14] @ PMC_IO_DPD_STATUS + mvn r1, r1 + bic r1, r1, #(1 << 31) + orr r1, r1, #(1 << 30) + str r1, [r2, #PMC_IO_DPD_REQ] @ DPD_OFF + + mov32 r0, TEGRA_EMC_BASE @ r0 reserved for emc base + + ldr r1, [r5, #0xC] @ restore EMC_XM2VTTGENPADCTRL + str r1, [r0, #EMC_XM2VTTGENPADCTRL] + ldr r1, [r5, #0x10] @ restore EMC_XM2VTTGENPADCTRL2 + str r1, [r0, #EMC_XM2VTTGENPADCTRL2] + ldr r1, [r5, #0x8] @ restore EMC_AUTO_CAL_INTERVAL + str r1, [r0, #EMC_AUTO_CAL_INTERVAL] + + /* Relock DLL */ + ldr r1, [r0, #EMC_CFG_DIG_DLL] + orr r1, r1, #(1 << 30) @ set DLL_RESET + str r1, [r0, #EMC_CFG_DIG_DLL] + + emc_timing_update r1, r0 + + ldr r1, [r0, #EMC_AUTO_CAL_CONFIG] + orr r1, r1, #(1 << 31) @ set AUTO_CAL_ACTIVE + str r1, [r0, #EMC_AUTO_CAL_CONFIG] + +emc_wait_auto_cal_onetime: + ldr r1, [r0, #EMC_AUTO_CAL_STATUS] + tst r1, #(1 << 31) @ wait until AUTO_CAL_ACTIVE is cleared + bne emc_wait_auto_cal_onetime + + ldr r1, [r0, #EMC_CFG] + bic r1, r1, #(1 << 31) @ disable DRAM_CLK_STOP_PD + str r1, [r0, #EMC_CFG] + + mov r1, #0 + str r1, [r0, #EMC_SELF_REF] @ take DRAM out of self refresh + mov r1, #1 + str r1, [r0, #EMC_NOP] + str r1, [r0, #EMC_NOP] + str r1, [r0, #EMC_REFRESH] + + emc_device_mask r1, r0 + +exit_selfrefresh_loop: + ldr r2, [r0, #EMC_EMC_STATUS] + ands r2, r2, r1 + bne exit_selfrefresh_loop + + lsr r1, r1, #8 @ devSel, bit0:dev0, bit1:dev1 + + mov32 r7, TEGRA_TMRUS_BASE + ldr r2, [r0, #EMC_FBIO_CFG5] + + and r2, r2, #3 @ check DRAM_TYPE + cmp r2, #2 + beq emc_lpddr2 + + /* Issue a ZQ_CAL for dev0 - DDR3 */ + mov32 r2, 0x80000011 @ DEV_SELECTION=2, LENGTH=LONG, CMD=1 + str r2, [r0, #EMC_ZQ_CAL] + ldr r2, [r7] + add r2, r2, #10 + wait_until r2, r7, r3 + + tst r1, #2 + beq zcal_done + + /* Issue a ZQ_CAL for dev1 - DDR3 */ + mov32 r2, 0x40000011 @ DEV_SELECTION=1, LENGTH=LONG, CMD=1 + str r2, [r0, #EMC_ZQ_CAL] + ldr r2, [r7] + add r2, r2, #10 + wait_until r2, r7, r3 + b zcal_done + +emc_lpddr2: + /* Issue a ZQ_CAL for dev0 - LPDDR2 */ + mov32 r2, 0x800A00AB @ DEV_SELECTION=2, MA=10, OP=0xAB + str r2, [r0, #EMC_MRW] + ldr r2, [r7] + add r2, r2, #1 + wait_until r2, r7, r3 + + tst r1, #2 + beq zcal_done + + /* Issue a ZQ_CAL for dev0 - LPDDR2 */ + mov32 r2, 0x400A00AB @ DEV_SELECTION=1, MA=10, OP=0xAB + str r2, [r0, #EMC_MRW] + ldr r2, [r7] + add r2, r2, #1 + wait_until r2, r7, r3 + +zcal_done: + mov r1, #0 @ unstall all transactions + str r1, [r0, #EMC_REQ_CTRL] + ldr r1, [r5, #0x4] @ restore EMC_ZCAL_INTERVAL + str r1, [r0, #EMC_ZCAL_INTERVAL] + ldr r1, [r5, #0x0] @ restore EMC_CFG + str r1, [r0, #EMC_CFG] + + mov32 r0, TEGRA_PMC_BASE + ldr r0, [r0, #PMC_SCRATCH41] + mov pc, r0 @ jump to tegra_resume +ENDPROC(tegra30_lp1_reset) + + .align L1_CACHE_SHIFT +tegra30_sdram_pad_address: + .word TEGRA_EMC_BASE + EMC_CFG @0x0 + .word TEGRA_EMC_BASE + EMC_ZCAL_INTERVAL @0x4 + .word TEGRA_EMC_BASE + EMC_AUTO_CAL_INTERVAL @0x8 + .word TEGRA_EMC_BASE + EMC_XM2VTTGENPADCTRL @0xc + .word TEGRA_EMC_BASE + EMC_XM2VTTGENPADCTRL2 @0x10 + .word TEGRA_PMC_BASE + PMC_IO_DPD_STATUS @0x14 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c + +tegra30_sdram_pad_size: + .word tegra30_sdram_pad_size - tegra30_sdram_pad_address + + .type tegra30_sdram_pad_save, %object +tegra30_sdram_pad_save: + .rept (tegra30_sdram_pad_size - tegra30_sdram_pad_address) / 4 + .long 0 + .endr + +/* + * tegra30_tear_down_core + * + * copied into and executed from IRAM + * puts memory in self-refresh for LP0 and LP1 + */ +tegra30_tear_down_core: + bl tegra30_sdram_self_refresh + bl tegra30_switch_cpu_to_clk32k + b tegra30_enter_sleep + +/* + * tegra30_switch_cpu_to_clk32k + * + * In LP0 and LP1 all PLLs will be turned off. Switching the CPU and System CLK + * to the 32KHz clock. + * r4 = TEGRA_PMC_BASE + * r5 = TEGRA_CLK_RESET_BASE + * r6 = TEGRA_FLOW_CTRL_BASE + * r7 = TEGRA_TMRUS_BASE + */ +tegra30_switch_cpu_to_clk32k: + /* + * start by jumping to CLKM to safely disable PLLs, then jump to + * CLKS. + */ + mov r0, #(1 << 28) + str r0, [r5, #CLK_RESET_SCLK_BURST] + /* 2uS delay delay between changing SCLK and CCLK */ + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r9 + str r0, [r5, #CLK_RESET_CCLK_BURST] + mov r0, #0 + str r0, [r5, #CLK_RESET_CCLK_DIVIDER] + str r0, [r5, #CLK_RESET_SCLK_DIVIDER] + + /* switch the clock source of mselect to be CLK_M */ + ldr r0, [r5, #CLK_RESET_CLK_SOURCE_MSELECT] + orr r0, r0, #MSELECT_CLKM + str r0, [r5, #CLK_RESET_CLK_SOURCE_MSELECT] + + /* 2uS delay delay between changing SCLK and disabling PLLs */ + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r9 + + /* disable PLLM via PMC in LP1 */ + ldr r0, [r4, #PMC_PLLP_WB0_OVERRIDE] + bic r0, r0, #(1 << 12) + str r0, [r4, #PMC_PLLP_WB0_OVERRIDE] + + /* disable PLLP, PLLA, PLLC and PLLX */ + ldr r0, [r5, #CLK_RESET_PLLP_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLP_BASE] + ldr r0, [r5, #CLK_RESET_PLLA_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLA_BASE] + ldr r0, [r5, #CLK_RESET_PLLC_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLC_BASE] + ldr r0, [r5, #CLK_RESET_PLLX_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLX_BASE] + + /* switch to CLKS */ + mov r0, #0 /* brust policy = 32KHz */ + str r0, [r5, #CLK_RESET_SCLK_BURST] + + mov pc, lr + /* * tegra30_enter_sleep * @@ -194,4 +585,105 @@ halted: /* !!!FIXME!!! Implement halt failure handler */ b halted +/* + * tegra30_sdram_self_refresh + * + * called with MMU off and caches disabled + * must be executed from IRAM + * r4 = TEGRA_PMC_BASE + * r5 = TEGRA_CLK_RESET_BASE + * r6 = TEGRA_FLOW_CTRL_BASE + * r7 = TEGRA_TMRUS_BASE + */ +tegra30_sdram_self_refresh: + + adr r2, tegra30_sdram_pad_address + adr r8, tegra30_sdram_pad_save + mov r9, #0 + + ldr r3, tegra30_sdram_pad_size +padsave: + ldr r0, [r2, r9] @ r0 is the addr in the pad_address + + ldr r1, [r0] + str r1, [r8, r9] @ save the content of the addr + + add r9, r9, #4 + cmp r3, r9 + bne padsave +padsave_done: + + dsb + + mov32 r0, TEGRA_EMC_BASE @ r0 reserved for emc base addr + + mov r1, #0 + str r1, [r0, #EMC_ZCAL_INTERVAL] + str r1, [r0, #EMC_AUTO_CAL_INTERVAL] + ldr r1, [r0, #EMC_CFG] + bic r1, r1, #(1 << 28) + str r1, [r0, #EMC_CFG] @ disable DYN_SELF_REF + + emc_timing_update r1, r0 + + ldr r1, [r7] + add r1, r1, #5 + wait_until r1, r7, r2 + +emc_wait_auto_cal: + ldr r1, [r0, #EMC_AUTO_CAL_STATUS] + tst r1, #(1 << 31) @ wait until AUTO_CAL_ACTIVE is cleared + bne emc_wait_auto_cal + + mov r1, #3 + str r1, [r0, #EMC_REQ_CTRL] @ stall incoming DRAM requests + +emcidle: + ldr r1, [r0, #EMC_EMC_STATUS] + tst r1, #4 + beq emcidle + + mov r1, #1 + str r1, [r0, #EMC_SELF_REF] + + emc_device_mask r1, r0 + +emcself: + ldr r2, [r0, #EMC_EMC_STATUS] + and r2, r2, r1 + cmp r2, r1 + bne emcself @ loop until DDR in self-refresh + + /* Put VTTGEN in the lowest power mode */ + ldr r1, [r0, #EMC_XM2VTTGENPADCTRL] + mov32 r2, 0xF8F8FFFF @ clear XM2VTTGEN_DRVUP and XM2VTTGEN_DRVDN + and r1, r1, r2 + str r1, [r0, #EMC_XM2VTTGENPADCTRL] + ldr r1, [r0, #EMC_XM2VTTGENPADCTRL2] + orr r1, r1, #7 @ set E_NO_VTTGEN + str r1, [r0, #EMC_XM2VTTGENPADCTRL2] + + emc_timing_update r1, r0 + + ldr r1, [r4, #PMC_CTRL] + tst r1, #PMC_CTRL_SIDE_EFFECT_LP0 + bne pmc_io_dpd_skip + /* + * Put DDR_DATA, DISC_ADDR_CMD, DDR_ADDR_CMD, POP_ADDR_CMD, POP_CLK + * and COMP in the lowest power mode when LP1. + */ + mov32 r1, 0x8EC00000 + str r1, [r4, #PMC_IO_DPD_REQ] +pmc_io_dpd_skip: + + dsb + + mov pc, lr + + .ltorg +/* dummy symbol for end of IRAM */ + .align L1_CACHE_SHIFT + .global tegra30_iram_end +tegra30_iram_end: + b . #endif diff --git a/arch/arm/mach-tegra/sleep.S b/arch/arm/mach-tegra/sleep.S index 8388113419fd..8d06213fbc47 100644 --- a/arch/arm/mach-tegra/sleep.S +++ b/arch/arm/mach-tegra/sleep.S @@ -134,10 +134,10 @@ ENTRY(tegra_shut_off_mmu) #ifdef CONFIG_CACHE_L2X0 /* Disable L2 cache */ check_cpu_part_num 0xc09, r9, r10 - movweq r4, #:lower16:(TEGRA_ARM_PERIF_BASE + 0x3000) - movteq r4, #:upper16:(TEGRA_ARM_PERIF_BASE + 0x3000) - moveq r5, #0 - streq r5, [r4, #L2X0_CTRL] + movweq r2, #:lower16:(TEGRA_ARM_PERIF_BASE + 0x3000) + movteq r2, #:upper16:(TEGRA_ARM_PERIF_BASE + 0x3000) + moveq r3, #0 + streq r3, [r2, #L2X0_CTRL] #endif mov pc, r0 ENDPROC(tegra_shut_off_mmu) diff --git a/arch/arm/mach-tegra/sleep.h b/arch/arm/mach-tegra/sleep.h index e907e406d129..a4edbb3abd3d 100644 --- a/arch/arm/mach-tegra/sleep.h +++ b/arch/arm/mach-tegra/sleep.h @@ -46,6 +46,14 @@ #define TEGRA_FLUSH_CACHE_ALL 1 #ifdef __ASSEMBLY__ +/* waits until the microsecond counter (base) is > rn */ +.macro wait_until, rn, base, tmp + add \rn, \rn, #1 +1001: ldr \tmp, [\base] + cmp \tmp, \rn + bmi 1001b +.endm + /* returns the offset of the flow controller halt register for a cpu */ .macro cpu_to_halt_reg rd, rcpu cmp \rcpu, #0 -- 2.39.5