From f8ff6a96cd6e9f7dc8b606f302129f99bcb82674 Mon Sep 17 00:00:00 2001 From: Jonathan Corbet Date: Sat, 11 Jun 2011 14:46:46 -0300 Subject: [PATCH] [media] marvell-cam: Move Cafe-specific register definitions to cafe-driver.c Nobody else ever needs to see these, so let's hide them. Signed-off-by: Jonathan Corbet Signed-off-by: Mauro Carvalho Chehab --- .../media/video/marvell-ccic/cafe-driver.c | 63 +++++++++++++++++++ drivers/media/video/marvell-ccic/mcam-core.h | 56 +---------------- 2 files changed, 64 insertions(+), 55 deletions(-) diff --git a/drivers/media/video/marvell-ccic/cafe-driver.c b/drivers/media/video/marvell-ccic/cafe-driver.c index 91ba74b3f55..1027265d46a 100644 --- a/drivers/media/video/marvell-ccic/cafe-driver.c +++ b/drivers/media/video/marvell-ccic/cafe-driver.c @@ -56,6 +56,69 @@ struct cafe_camera { wait_queue_head_t smbus_wait; /* Waiting on i2c events */ }; +/* + * Most of the camera controller registers are defined in mcam-core.h, + * but the Cafe platform has some additional registers of its own; + * they are described here. + */ + +/* + * "General purpose register" has a couple of GPIOs used for sensor + * power and reset on OLPC XO 1.0 systems. + */ +#define REG_GPR 0xb4 +#define GPR_C1EN 0x00000020 /* Pad 1 (power down) enable */ +#define GPR_C0EN 0x00000010 /* Pad 0 (reset) enable */ +#define GPR_C1 0x00000002 /* Control 1 value */ +/* + * Control 0 is wired to reset on OLPC machines. For ov7x sensors, + * it is active low. + */ +#define GPR_C0 0x00000001 /* Control 0 value */ + +/* + * These registers control the SMBUS module for communicating + * with the sensor. + */ +#define REG_TWSIC0 0xb8 /* TWSI (smbus) control 0 */ +#define TWSIC0_EN 0x00000001 /* TWSI enable */ +#define TWSIC0_MODE 0x00000002 /* 1 = 16-bit, 0 = 8-bit */ +#define TWSIC0_SID 0x000003fc /* Slave ID */ +#define TWSIC0_SID_SHIFT 2 +#define TWSIC0_CLKDIV 0x0007fc00 /* Clock divider */ +#define TWSIC0_MASKACK 0x00400000 /* Mask ack from sensor */ +#define TWSIC0_OVMAGIC 0x00800000 /* Make it work on OV sensors */ + +#define REG_TWSIC1 0xbc /* TWSI control 1 */ +#define TWSIC1_DATA 0x0000ffff /* Data to/from camchip */ +#define TWSIC1_ADDR 0x00ff0000 /* Address (register) */ +#define TWSIC1_ADDR_SHIFT 16 +#define TWSIC1_READ 0x01000000 /* Set for read op */ +#define TWSIC1_WSTAT 0x02000000 /* Write status */ +#define TWSIC1_RVALID 0x04000000 /* Read data valid */ +#define TWSIC1_ERROR 0x08000000 /* Something screwed up */ + +/* + * Here's the weird global control registers + */ +#define REG_GL_CSR 0x3004 /* Control/status register */ +#define GCSR_SRS 0x00000001 /* SW Reset set */ +#define GCSR_SRC 0x00000002 /* SW Reset clear */ +#define GCSR_MRS 0x00000004 /* Master reset set */ +#define GCSR_MRC 0x00000008 /* HW Reset clear */ +#define GCSR_CCIC_EN 0x00004000 /* CCIC Clock enable */ +#define REG_GL_IMASK 0x300c /* Interrupt mask register */ +#define GIMSK_CCIC_EN 0x00000004 /* CCIC Interrupt enable */ + +#define REG_GL_FCR 0x3038 /* GPIO functional control register */ +#define GFCR_GPIO_ON 0x08 /* Camera GPIO enabled */ +#define REG_GL_GPIOR 0x315c /* GPIO register */ +#define GGPIO_OUT 0x80000 /* GPIO output */ +#define GGPIO_VAL 0x00008 /* Output pin value */ + +#define REG_LEN (REG_GL_IMASK + 4) + + /* * Debugging and related. */ diff --git a/drivers/media/video/marvell-ccic/mcam-core.h b/drivers/media/video/marvell-ccic/mcam-core.h index 21485e7ec8f..e8a7de05100 100644 --- a/drivers/media/video/marvell-ccic/mcam-core.h +++ b/drivers/media/video/marvell-ccic/mcam-core.h @@ -249,63 +249,9 @@ int mccic_resume(struct mcam_camera *cam); #define REG_CLKCTRL 0x88 /* Clock control */ #define CLK_DIV_MASK 0x0000ffff /* Upper bits RW "reserved" */ -#define REG_GPR 0xb4 /* General purpose register. This - controls inputs to the power and reset - pins on the OV7670 used with OLPC; - other deployments could differ. */ -#define GPR_C1EN 0x00000020 /* Pad 1 (power down) enable */ -#define GPR_C0EN 0x00000010 /* Pad 0 (reset) enable */ -#define GPR_C1 0x00000002 /* Control 1 value */ -/* - * Control 0 is wired to reset on OLPC machines. For ov7x sensors, - * it is active low, for 0v6x, instead, it's active high. What - * fun. - */ -#define GPR_C0 0x00000001 /* Control 0 value */ - -#define REG_TWSIC0 0xb8 /* TWSI (smbus) control 0 */ -#define TWSIC0_EN 0x00000001 /* TWSI enable */ -#define TWSIC0_MODE 0x00000002 /* 1 = 16-bit, 0 = 8-bit */ -#define TWSIC0_SID 0x000003fc /* Slave ID */ -#define TWSIC0_SID_SHIFT 2 -#define TWSIC0_CLKDIV 0x0007fc00 /* Clock divider */ -#define TWSIC0_MASKACK 0x00400000 /* Mask ack from sensor */ -#define TWSIC0_OVMAGIC 0x00800000 /* Make it work on OV sensors */ - -#define REG_TWSIC1 0xbc /* TWSI control 1 */ -#define TWSIC1_DATA 0x0000ffff /* Data to/from camchip */ -#define TWSIC1_ADDR 0x00ff0000 /* Address (register) */ -#define TWSIC1_ADDR_SHIFT 16 -#define TWSIC1_READ 0x01000000 /* Set for read op */ -#define TWSIC1_WSTAT 0x02000000 /* Write status */ -#define TWSIC1_RVALID 0x04000000 /* Read data valid */ -#define TWSIC1_ERROR 0x08000000 /* Something screwed up */ - - +/* This appears to be a Cafe-only register */ #define REG_UBAR 0xc4 /* Upper base address register */ -/* - * Here's the weird global control registers which are said to live - * way up here. - */ -#define REG_GL_CSR 0x3004 /* Control/status register */ -#define GCSR_SRS 0x00000001 /* SW Reset set */ -#define GCSR_SRC 0x00000002 /* SW Reset clear */ -#define GCSR_MRS 0x00000004 /* Master reset set */ -#define GCSR_MRC 0x00000008 /* HW Reset clear */ -#define GCSR_CCIC_EN 0x00004000 /* CCIC Clock enable */ -#define REG_GL_IMASK 0x300c /* Interrupt mask register */ -#define GIMSK_CCIC_EN 0x00000004 /* CCIC Interrupt enable */ - -#define REG_GL_FCR 0x3038 /* GPIO functional control register */ -#define GFCR_GPIO_ON 0x08 /* Camera GPIO enabled */ -#define REG_GL_GPIOR 0x315c /* GPIO register */ -#define GGPIO_OUT 0x80000 /* GPIO output */ -#define GGPIO_VAL 0x00008 /* Output pin value */ - -#define REG_LEN (REG_GL_IMASK + 4) - - /* * Useful stuff that probably belongs somewhere global. */ -- 2.39.5