#
# Physical Layer USB driver configuration
#
-menuconfig USB_PHY
- bool "USB Physical Layer drivers"
- help
- Most USB controllers have the physical layer signalling part
- (commonly called a PHY) built in. However, dual-role devices
- (a.k.a. USB on-the-go) which support being USB master or slave
- with the same connector often use an external PHY.
-
- The drivers in this submenu add support for such PHY devices.
- They are not needed for standard master-only (or the vast
- majority of slave-only) USB interfaces.
-
- If you're not sure if this applies to you, it probably doesn't;
- say N here.
+menu "USB Physical Layer drivers"
-if USB_PHY
+config USB_PHY
+ def_bool n
#
# USB Transceiver Drivers
config AB8500_USB
tristate "AB8500 USB Transceiver Driver"
depends on AB8500_CORE
+ select USB_PHY
help
Enable this to support the USB OTG transceiver in AB8500 chip.
This transceiver supports high and full speed devices plus,
bool "Freescale USB OTG Transceiver Driver"
depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
select USB_OTG
+ select USB_PHY
help
Enable this to support Freescale USB OTG transceiver.
config ISP1301_OMAP
tristate "Philips ISP1301 with OMAP OTG"
depends on I2C && ARCH_OMAP_OTG
+ select USB_PHY
help
If you say yes here you get support for the Philips ISP1301
USB-On-The-Go transceiver working with the OMAP OTG controller.
config MV_U3D_PHY
bool "Marvell USB 3.0 PHY controller Driver"
depends on CPU_MMP3
+ select USB_PHY
help
Enable this to support Marvell USB 3.0 phy controller for Marvell
SoC.
config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
+ select USB_PHY
help
This driver is to be used by all the usb transceiver which are either
built-in with usb ip or which are autonomous and doesn't require any
config OMAP_CONTROL_USB
tristate "OMAP CONTROL USB Driver"
+ depends on ARCH_OMAP2PLUS || COMPILE_TEST
help
Enable this to add support for the USB part present in the control
module. This driver has API to power on the USB2 PHY and to write to
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
additional register to power on USB3 PHY.
-config OMAP_USB2
- tristate "OMAP USB2 PHY Driver"
- depends on ARCH_OMAP2PLUS
- select OMAP_CONTROL_USB
- help
- Enable this to support the transceiver that is part of SOC. This
- driver takes care of all the PHY functionality apart from comparator.
- The USB OTG controller communicates with the comparator using this
- driver.
-
config OMAP_USB3
tristate "OMAP USB3 PHY Driver"
+ depends on ARCH_OMAP2PLUS || COMPILE_TEST
select OMAP_CONTROL_USB
+ select USB_PHY
help
Enable this to support the USB3 PHY that is part of SOC. This
driver takes care of all the PHY functionality apart from comparator.
This driver interacts with the "OMAP Control USB Driver" to power
on/off the PHY.
+config AM335X_CONTROL_USB
+ tristate
+
+config AM335X_PHY_USB
+ tristate "AM335x USB PHY Driver"
+ depends on ARM || COMPILE_TEST
+ select USB_PHY
+ select AM335X_CONTROL_USB
+ select NOP_USB_XCEIV
+ help
+ This driver provides PHY support for that phy which part for the
+ AM335x SoC.
+
config SAMSUNG_USBPHY
tristate
help
config SAMSUNG_USB2PHY
tristate "Samsung USB 2.0 PHY controller Driver"
select SAMSUNG_USBPHY
+ select USB_PHY
help
Enable this to support Samsung USB 2.0 (High Speed) PHY controller
driver for Samsung SoCs.
config SAMSUNG_USB3PHY
tristate "Samsung USB 3.0 PHY controller Driver"
select SAMSUNG_USBPHY
+ select USB_PHY
help
Enable this to support Samsung USB 3.0 (Super Speed) phy controller
for samsung SoCs.
-config TWL4030_USB
- tristate "TWL4030 USB Transceiver Driver"
- depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
- help
- Enable this to support the USB OTG transceiver on TWL4030
- family chips (including the TWL5030 and TPS659x0 devices).
- This transceiver supports high and full speed devices plus,
- in host mode, low speed.
-
config TWL6030_USB
tristate "TWL6030 USB Transceiver Driver"
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
config USB_GPIO_VBUS
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
depends on GPIOLIB
+ select USB_PHY
help
Provides simple GPIO VBUS sensing for controllers with an
internal transceiver via the usb_phy interface, and
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
depends on I2C
+ select USB_PHY
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
config USB_MSM_OTG
tristate "OTG support for Qualcomm on-chip USB controller"
depends on (USB || USB_GADGET) && ARCH_MSM
+ select USB_PHY
help
Enable this to support the USB OTG transceiver on MSM chips. It
handles PHY initialization, clock management, and workarounds
tristate "Marvell USB OTG support"
depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
select USB_OTG
+ select USB_PHY
help
Say Y here if you want to build Marvell USB OTG transciever
driver in kernel (including PXA and MMP series). This driver
tristate "Freescale MXS USB PHY support"
depends on ARCH_MXC || ARCH_MXS
select STMP_DEVICE
+ select USB_PHY
help
Enable this to support the Freescale MXS USB PHY.
config USB_RCAR_PHY
tristate "Renesas R-Car USB PHY support"
depends on USB || USB_GADGET
+ select USB_PHY
help
Say Y here to add support for the Renesas R-Car USB common PHY driver.
This chip is typically used as USB PHY for USB host, gadget.
To compile this driver as a module, choose M here: the
module will be called phy-rcar-usb.
+config USB_RCAR_GEN2_PHY
+ tristate "Renesas R-Car Gen2 USB PHY support"
+ depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST
+ select USB_PHY
+ help
+ Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver.
+ It is typically used to control internal USB PHY for USBHS,
+ and to configure shared USB channels 0 and 2.
+ This driver supports R8A7790 and R8A7791.
+
+ To compile this driver as a module, choose M here: the
+ module will be called phy-rcar-gen2-usb.
+
config USB_ULPI
bool "Generic ULPI Transceiver Driver"
depends on ARM
Provides read/write operations to the ULPI phy register set for
controllers with a viewport register (e.g. Chipidea/ARC controllers).
-endif # USB_PHY
+endmenu
projects / karo-tx-linux.git / blobdiff