Jeremie Samuel [Mon, 21 Oct 2013 15:25:52 +0000 (17:25 +0200)]
mmc: sdhci: Use work structs instead of tasklets
The driver can happily live without an atomic context and tasklets,
so turn the tasklets into the work structs.
Tasklets handlers still grab irqsave spinlocks, but we'll deal
with it in a separate patch.
Patch based on: http://thread.gmane.org/gmane.linux.kernel.mmc/2579.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Jeremie Samuel <jeremie.samuel.ext@parrot.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Jeremie Samuel [Mon, 21 Oct 2013 15:25:50 +0000 (17:25 +0200)]
mmc: sdhci: Turn timeout timer into delayed work
There is no need for the timeout handler to run in the atomic
context, so this patch turns timeout timeout into the delayed
work.
Note that the timeout handler still grabs an irqsave spinlock,
we'll deal with it in a separate patch.
Patch based on http://thread.gmane.org/gmane.linux.kernel.mmc/2579.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Jeremie Samuel <jeremie.samuel.ext@parrot.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Dong Aisheng [Fri, 18 Oct 2013 11:48:47 +0000 (19:48 +0800)]
mmc: sdhci-esdhc-imx: add delay line setting support
The DLL(Delay Line) is newly added to assist in sampling read data.
The DLL provides the ability to programmatically select a quantized
delay (in fractions of the clock period) regardless of on-chip variations
such as process, voltage and temperature (PVT).
This patch adds a user interface to set slave delay line via device tree.
It's usually used in high speed mode like mmc DDR mode when the signal
quality is not good caused by board design, e.g. the signal path is too
long. User can manually set delay line to find a suitable data sampling
window for card to work properly.
Dong Aisheng [Fri, 18 Oct 2013 11:48:46 +0000 (19:48 +0800)]
mmc: sdhci-esdhc-imx: add DDR mode support for mx6
When DDR mode is enabled, the initial pre_div should be 2.
And the pre_div value should be changed accordingly
from
...
02h) Base clock divided by 4
01h) Base clock divided by 2
00h) Base clock divided by 1
to
..
02h) Base clock divided by 8
01h) Base clock divided by 4
00h) Base clock divided by 2
Dong Aisheng [Fri, 18 Oct 2013 11:48:45 +0000 (19:48 +0800)]
mmc: sdhci: report error once the maximum tuning loops exhausted or timeout
The original code missed to report an error when the maximum tuning
loops exhausted or timeout, it will cause the upper layer to wrongly
think the tuning process is passed.
Dong Aisheng [Fri, 18 Oct 2013 11:48:43 +0000 (19:48 +0800)]
mmc: sdhci-esdhc-imx: add std tuning support for mx6sl
The mx6sl supports standard sdhci tuning, then esdhc_executing_tuning
is only needed for mx6q/dl. We introduce is_imx6_usdhc() and
is_imx6sl_usdhc() to handle the difference.
The standard tuning is enabled by setting ESDHC_TUNE_CTRL_STD_TUNING_EN bit
in new register ESDHC_TUNE_CTRL and operates with new tuning bits
defined in SDHCI_ACMD12_ERR register.
Note: mx6sl can also work on the old manually tuning mode as mx6q/dl if
not enable standard tuning mode.
Create a struct esdhc_soc_data with moving 'flags' field from
pltfm_imx_data into it, and pass the pointer of this SoC specific data
structure through of_device_id.data directly, so that the translation
from enum imx_esdhc_type to flags can be saved.
With the change, enum imx_esdhc_type can be eliminated, since we can
implement the is_imx*_esdhc() by checking the esdhc_soc_data pointer.
The unused is_imx35_esdhc() and is_imx51_esdhc() are also removed, and the
others are kept there as we will need to use them to handle some small
register differences later, where use of new flags might be a little
overkilled.
Shawn Guo [Thu, 17 Oct 2013 07:19:46 +0000 (15:19 +0800)]
mmc: sdhci-esdhc-imx: pdev->id_entry should be immutable
As a good practice, device driver should not modify pdev->id_entry but
keep it immutable. Let's assign of_device_id.data with imx_esdhc_type
constants directly, so that we do not have to manipulate pdev->id_entry
in .probe().
As the result, sdhci-esdhc-imx53 and sdhci-usdhc-imx6q can be removed
from platform_device_id table now, since they will only probe from
device tree.
Shawn Guo [Thu, 17 Oct 2013 07:19:45 +0000 (15:19 +0800)]
mmc: sdhci-esdhc-imx: add flag ESDHC_FLAG_USDHC
Add flag ESDHC_FLAG_USDHC to tell that the ESDHC is actually an USDHC
block, and replace the is_imx6q_usdhc() occurrences with inline function
esdhc_is_usdhc() which checks the flag.
Shawn Guo [Thu, 17 Oct 2013 07:19:44 +0000 (15:19 +0800)]
mmc: sdhci-esdhc-imx: add flag ESDHC_FLAG_ENGCM07207
Just like the use of the flag ESDHC_FLAG_MULTIBLK_NO_INT, let's add
another flag ESDHC_FLAG_ENGCM07207 to enable the workaround for errata
ENGcm07207 and set the flag for i.MX25 and i.MX35 ESDHC.
While at it, let's use BIT() macro for ESDHC_FLAG_MULTIBLK_NO_INT as
well.
According to spec, the pre_div for imx6q should be 1, or the biggest
clock rate we can get is a half of host clock rate. This may cause
we can not get the proper clock rate as we want. e.g. if the desired
clock is 200Mhz, however, the host clock is 200Mhz too, then it causes
the actual clock we get is 100Mhz due to pre_div is 2.
mmc: sdhci-esdhc-imx: add sd3.0 SDR clock tuning support
Freescale i.MX6Q/DL uSDHC clock tuning progress is a little different from
the standard tuning process defined in host controller spec v3.0.
Thus we use platform_execute_tuning instead of standard sdhci tuning.
The main difference are:
1) not only generate Buffer Read Ready interrupt when tuning is performing.
It generates all other DATA interrupts like the normal data command.
2) SDHCI_CTRL_EXEC_TUNING is not automatically cleared by HW,
instead it's controlled by SW.
3) SDHCI_CTRL_TUNED_CLK is not automatically set by HW,
it's controlled by SW.
4) the clock delay for every tuning is set by SW.
mmc: sdhci-esdhc-imx: support real clock on and off for imx6q
The signal voltage switch flow requires to shutdown and output
clock in a specific sequence according to standard host controller
v3.0 spec. In that timing, the card must really receive clock or not.
However, for i.MX6Q, the uSDHC will not output clock even the clock
is enabled until there is command or data in transfer on the bus,
which will then cause singal voltage switch always to fail.
For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let
controller to gate off clock automatically and set that bit
to force clock output if clock is on.
mmc: sdhci-esdhc: move common esdhc_set_clock to platform driver
We need a lot of imx6 specific things into common esdhc_set_clock
for support SD3.0 and eMMC DDR mode which is not needed for power pc
platforms, so esdhc_set_clock seems not so common anymore.
Instead of keeping add platform specfics things into this common API,
we choose to move that code into platform driver itself to handle.
This can also exclude the dependency between imx and power pc on this
headfile and is easy for maintain in the future.
mmc: sdhci: add hooks for platform specific tuning
The tuning of some platforms may not follow the standard host control
spec v3.0, e.g. Freescale uSDHC on i.MX6Q/DL.
Add a hook here to allow execute platform specific tuning instead of
standard host controller tuning.
The hook only replaces the tuning process, so it's placed after tuning
checking and before the real tuning process.
Some notes for the tuning hook:
1) it needs handle lock itself if it wants to access host controller
according platform specific implementation.
2) do not need to handle runtime pm since it executes with runtime pm
get already.
Axel Lin [Tue, 17 Sep 2013 07:59:32 +0000 (15:59 +0800)]
mmc: sdhci-bcm-kona: Use sdhci_pltfm_unregister instead of open coded
This avoid duplicated implementation and also fixes missing iounmap() and
release_mem_region() calls in sdhci_bcm_kona_remove(). sdhci_pltfm_init()
calls request_mem_region() and ioremap(), thus we need to call the
corresponding iounmap() and release_mem_region() calls in
sdhci_bcm_kona_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Chris Ball <cjb@laptop.org>
When a software timeout occurs, the transfer is not stopped. In DMA case,
it causes DMA channel to be stuck because the transfer is still active
causing following transfers to be queued but not computed.
Cc: <stable@vger.kernel.org> # 3.9+ Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Reported-by: Alexander Morozov <etesial@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
While speed mode is changed, CMD13 cannot be guaranteed.
According to the spec., it is not recommended to use CMD13
to check the busy completion of the timing change.
If CMD13 is used in this case, CRC error must be ignored.
Seungwon Jeon [Fri, 30 Aug 2013 15:14:38 +0000 (00:14 +0900)]
mmc: dw_mmc: fix the transfer termination in IDMAC mode
In IDMAC mode EVENT_XFER_COMPLETE is set when RI/TI of last descriptor
is done. So if errors are happened in the middle of data transfers,
'dw_mci_stop_dma' during error handing can be called and eventually
prevents this flag to be set. This results in permanent wait for
EVENT_XFER_COMPLETE in 'dw_mci_tasklet_func'. Therefore, if dma
running is stopped forcibly, EVENT_XFER_COMPLETE should be set.
Reported-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:14:33 +0000 (00:14 +0900)]
mmc: dw_mmc: amend use of idmac sw reset
First, compiling warning along with previous change is removed.
[drivers/mmc/host/dw_mmc.c:1890:7: warning: unused variable 'ctrl']
And with the recommendation in manual, IDMAC software reset is followed
by dma-reset of the CTRL register in order to terminate the transfer.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:14:23 +0000 (00:14 +0900)]
mmc: dw_mmc: gather each reset code into functions
There are three resets in CTRL register. FIFO reset is especially used
in several points with the same routine. It could be replaced with one
function and the others may be applied similarly if needed. So,
mci_wait_reset() is modified to allow various bit field of reset.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:14:05 +0000 (00:14 +0900)]
mmc: dw_mmc: guarantee stop-abort cmd in data errors
In error cases, DTO interrupt may or may not be generated depending
on remained data. Stop/Abort command ensures DTO generation for that
situation. Currently if 'stop' field of data is empty, there is no
stop/abort command. So, it could hang waiting DTO. This change
reinforces these cases.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:13:59 +0000 (00:13 +0900)]
mmc: dw_mmc: fix error handling on response error
Even if response error is detected in case data command, data transfer
is continued. It means that data can live in FIFO. Current handling
just breaks out the request when seeing the command error. This causes
kernel panic in dw_mci_read_data_pio() [host->data = NULL]. And also,
FIFO should be guaranteed to be empty.
Seungwon Jeon [Fri, 30 Aug 2013 15:13:55 +0000 (00:13 +0900)]
mmc: dw_mmc: control card read threshold
Card Read Threshold should be ensured that the card clock does not stop
in the middle of a block of data being transferred from the card to the
Host. Specially, clock stop is allowed in fast transfer such as HS200
or SDR104 mode. And so, it should be enabled.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:13:42 +0000 (00:13 +0900)]
mmc: dw_mmc: adjust the fifoth with block size
This change helps to choose msize, rx_watermark and tx_watermark
depending on block size for IDMAC mode. For SDIO block size can be
variable, so if these values are set incorrectly, card clock may stop.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:13:31 +0000 (00:13 +0900)]
mmc: dw_mmc: set the supported max/min frequency
Both f_max and f_min will be informed for core layer to request
valid clock rate. But current setting from 'host->bus_hz' may
not represent the max/min frequency properly. Even if host can
actually support high speed than bus_hz, core layer will not
request clock rate over bus_hz. Basically, f_max/f_min can be set
with the values according to spec. And then host will make its best
effort to meet the rate.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:13:03 +0000 (00:13 +0900)]
mmc: dw_mmc: exynos: adjust the clock rate with speed mode
Exynos's host has divider logic before 'cclk_in' to controller core.
It means that actual clock rate of ciu clock comes from this divider
value. So, source clock should be adjusted along with 'ciu_div' which
indicates the host's divider ratio. Setting clock rate basically fits
the required speed. Specially, 'cclk_in' should have double rate of
target speed in case of DDR 8-bit mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Fri, 30 Aug 2013 15:12:42 +0000 (00:12 +0900)]
mmc: dw_mmc: add support tuning scheme
For the speed modes HS200 and SDR104, tuning is needed to determine the
correct sampling point. Actual tuning procedure is provided by specific
host controller driver. This patch defines the tuning command and
tuning data. Additionally, 'struct dw_mci_slot' is moved to header
file to consider the extensive usages in driver.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Exynos5420 Mobile Storage Host controller has Security Management
Unit (SMU) for channel 0 and channel 1 (mainly for eMMC).
This time, SMU configuration is set for non-encryption mode.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Current platform specific private data initialization call
dw_mci_exynos_priv_init() can be used to do platform specific
initialization of SMU and others in future. So the drv_data->init
call has moved to dw_mci_probe().
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Currently platform specific private data initialization is done by
dw_mci_socfpga_priv_init and dw_mci_socfpga_parse_dt. As we already have
separate platform specific device tree parser dw_mci_socfpga_parse_dt,
move the dw_mci_socfpga_priv_init code to dw_mci_socfpga_parse_dt.
We can use the dw_mci_socfpga_priv_init to do some actual platform
specific initialization.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Currently platform specific private data initialization is done by
dw_mci_exynos_priv_init and dw_mci_exynos_parse_dt. As we already have
separate platform specific device tree parser dw_mci_exynos_parse_dt,
move the dw_mci_exynos_priv_init code to dw_mci_exynos_parse_dt.
We can use the dw_mci_exynos_priv_init to do some actual platform
specific initialization of SMU and etc.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Doug Anderson [Fri, 30 Aug 2013 15:11:49 +0000 (00:11 +0900)]
mmc: dw_mmc: Set timeout to max upon resume
The TMOUT register is set to 0xffffffff at probe time but isn't
set after suspend/resume. Add an init of this value.
No problems were observed without this (it will also be set in
__dw_mci_start_request if there is data to send), but it makes the
register dump before and after suspend cleaner.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Doug Anderson [Fri, 30 Aug 2013 15:11:43 +0000 (00:11 +0900)]
mmc: dw_mmc: Honor requests to set the clock to 0
Previously the dw_mmc driver would ignore any requests to disable the
card's clock. This doesn't seem like a good thing in general, but had
one extra bad side effect in the following situation:
* mmc core would set clk to 400kHz at boot time while scanning
* mmc core would set clk to 0 since no card, but it would be ignored.
* suspend to ram and resume; clocks in the dw_mmc IP block are now 0
but dw_mmc thinks that they're 400kHz (it ignored the set to 0).
* insert card
* mmc core would set clk to 400kHz which would be considered a no-op.
Note that if there is no card in the slot and we do a suspend/resume
cycle, we _do_ still end up with differences in a dw_mmc register
dump, but the differences are clock related and we've got the clock
disabled both before and after, so this should be OK.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Doug Anderson [Fri, 30 Aug 2013 15:11:21 +0000 (00:11 +0900)]
mmc: dw_mmc: Add exynos resume_noirq callback to clear WAKEUP_INT
If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up
looping around forever. This has been seen to happen on exynos5420
silicon despite the fact that we haven't enabled any wakeup events due
to a silicon errata. It is safe to do on all exynos variants.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Doug Anderson [Fri, 30 Aug 2013 15:11:06 +0000 (00:11 +0900)]
mmc: dw_mmc: don't queue up a card detect at slot startup
The MMC subsystem handles looking for a card at probe time. Queuing up our
own can race with the rest of the MMC subsystem and cause problems if we
get unlucky with timing. Just remove driver own detection triggering. While
progressing the request from 'mmc_rescan', if 'dw_mci_work_routine_card'
routine is activated, it will cancel the current request. The problem case
is that 'mmc_rescan' is prior to 'dw_mci_work_routine_card' from host own.
Specifically, the following message shows the detection problem in driver's
probing. It would get an err -123 (-ENOMEDIUM) during probe.
[ 4.216595] dwmmc_exynos 12210000.dwmmc1: Using internal DMA controller.
[ 4.395935] dwmmc_exynos 12210000.dwmmc1: Version ID is 250a
[ 4.401948] dwmmc_exynos 12210000.dwmmc1: DW MMC controller at irq 108, 64 bit host data width, 64 deep fifo
[ 4.424430] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.453975] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.459592] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 4.484258] dwmmc_exynos 12210000.dwmmc1: 1 slots initialized
[ 4.485406] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.487606] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.489794] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.509757] mmc1: error -123 whilst initialising SDIO card
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
afa2c9407f8908 ("sh: ecovec24: Use MMC/SDHI CD and RO GPIO") added
.tmio_flags = TMIO_MMC_USE_GPIO_CD on sh_mobile_sdhi_info, but it needs
<linux/mfd/tmio.h> header. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Merge tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes and one update to the kernel-paramters.txt documentation.
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount
of memory
- Add xen_nopvpsin parameter to the documentation"
* tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Document the xen_nopvspin parameter.
xen/p2m: check MFN is in range before using the m2p table
xen/balloon: don't alloc page while non-preemptible
xen: Do not enable spinlocks before jump_label_init() has executed
tpm: xen-tpmfront: Remove the locality sysfs attribute
tpm: xen-tpmfront: Fix default durations
Merge tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
- A small cleanup the main purpose of which is to work around an
internal compiler error bug in certain Codesource toolchains.
* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Move some checks out of 'for' loop in DMA operations
MIPS: cpu-features.h: s/MIPS53/MIPS64/
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few things for -rc2, this time it's all written by me so it
can only be perfect .... right ? :)
So we have the fix to call irq_enter/exit on the irq stack we've been
discussing, plus a cleanup on top to remove an unused (and broken)
stack limit tracking feature (well, make it 32-bit only in fact where
it is used and works properly).
Then we have two things that I wrote over the last couple of days and
made the executive decision to include just because I can (and I'm
sure you won't object .... right ?).
They fix a couple of annoying and long standing "issues":
- We had separate zImages for when booting via Open Firmware vs.
booting via a flat device-tree, while it's trivial to make one that
deals with both
- We wasted a ton of cycles spinning secondary CPUs uselessly at boot
instead of starting them when needed on pseries, thus contributing
significantly to global warming"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Do not start secondaries in Open Firmware
powerpc/zImage: make the "OF" wrapper support ePAPR boot
powerpc: Remove ksp_limit on ppc64
powerpc/irq: Run softirqs off the top of the irq stack
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Three small fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/balancing: Fix cfs_rq->task_h_load calculation
sched/balancing: Fix 'local->avg_load > busiest->avg_load' case in fix_small_imbalance()
sched/balancing: Fix 'local->avg_load > sds->avg_load' case in calculate_imbalance()
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Assorted standalone fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add model number for Avoton Silvermont
perf: Fix capabilities bitfield compatibility in 'struct perf_event_mmap_page'
perf/x86/intel/uncore: Don't use smp_processor_id() in validate_group()
perf: Update ABI comment
tools lib lk: Uninclude linux/magic.h in debugfs.c
perf tools: Fix old GCC build error in trace-event-parse.c:parse_proc_kallsyms()
perf probe: Fix finder to find lines of given function
perf session: Check for SIGINT in more loops
perf tools: Fix compile with libelf without get_phdrnum
perf tools: Fix buildid cache handling of kallsyms with kcore
perf annotate: Fix objdump line parsing offset validation
perf tools: Fill in new definitions for madvise()/mmap() flags
perf tools: Sharpen the libaudit dependencies test
My old @it.uu.se email address is going away, so update relevant
files to point to my @gmail.com address instead. In sata_promise.c
just delete the address, people can get it from MAINTAINERS.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jayachandran C [Wed, 25 Sep 2013 13:01:05 +0000 (18:31 +0530)]
MIPS: mm: Move some checks out of 'for' loop in DMA operations
The check cpu_needs_post_dma_flush() in mips_dma_sync_sg_for_cpu() and
the check !plat_device_is_coherent() in mips_dma_sync_sg_for_device()
can be moved outside the for loop.
As a side effect, this also avoids a GCC bug that caused kernel compile
to fail with the error:
arch/mips/mm/dma-default.c: In function 'mips_dma_sync_sg_for_cpu':
arch/mips/mm/dma-default.c:316:1: internal compiler error: in add_insn_before, at emit-rtl.c:3852
This gcc failure is seen in Code Sourcery toolchains [e.g. gcc version
4.7.2 (Sourcery CodeBench Lite 2012.09-99)] after commit "MIPS: Optimize
current_cpu_type() for better code."
xen/spinlock: Document the xen_nopvspin parameter.
Which disables in the ticketlock slowpath the Xen PV optimization's.
Useful for diagnosing issues and comparing benchmarks in
over-commit CPU scenarios.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
David Vrabel [Fri, 13 Sep 2013 14:13:30 +0000 (15:13 +0100)]
xen/p2m: check MFN is in range before using the m2p table
On hosts with more than 168 GB of memory, a 32-bit guest may attempt
to grant map an MFN that is error cannot lookup in its mapping of the
m2p table. There is an m2p lookup as part of m2p_add_override() and
m2p_remove_override(). The lookup falls off the end of the mapped
portion of the m2p and (because the mapping is at the highest virtual
address) wraps around and the lookup causes a fault on what appears to
be a user space address.
do_page_fault() (thinking it's a fault to a userspace address), tries
to lock mm->mmap_sem. If the gntdev device is used for the grant map,
m2p_add_override() is called from from gnttab_mmap() with mm->mmap_sem
already locked. do_page_fault() then deadlocks.
The deadlock would most commonly occur when a 64-bit guest is started
and xenconsoled attempts to grant map its console ring.
Introduce mfn_to_pfn_no_overrides() which checks the MFN is within the
mapped portion of the m2p table before accessing the table and use
this in m2p_add_override(), m2p_remove_override(), and mfn_to_pfn()
(which already had the correct range check).
All faults caused by accessing the non-existant parts of the m2p are
thus within the kernel address space and exception_fixup() is called
without trying to lock mm->mmap_sem.
This means that for MFNs that are outside the mapped range of the m2p
then mfn_to_pfn() will always look in the m2p overrides. This is
correct because it must be a foreign MFN (and the PFN in the m2p in
this case is only relevant for the other domain).
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Stefano Stabellini <stefano.stabellini@citrix.com> Cc: Jan Beulich <JBeulich@suse.com>
--
v3: check for auto_translated_physmap in mfn_to_pfn_no_overrides()
v2: in mfn_to_pfn() look in m2p_overrides if the MFN is out of
range as it's probably foreign. Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
powerpc/pseries: Do not start secondaries in Open Firmware
Starting secondary CPUs early on from Open Firmware and placing them
in a holding spin loop slows down the boot process significantly under
some hypervisors such as KVM.
This is also unnecessary when RTAS supports querying the CPU state
So let's not do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/zImage: make the "OF" wrapper support ePAPR boot
This makes the "OF" zImage wrapper (zImage.pseries, zImage.pmac,
zImage.maple) work if booted via a flat device-tree (ePAPR boot
mode), and thus potentially usable with kexec.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've been keeping that field in thread_struct for a while, it contains
the "limit" of the current stack pointer and is meant to be used for
detecting stack overflows.
It has a few problems however:
- First, it was never actually *used* on 64-bit. Set and updated but
not actually exploited
- When switching stack to/from irq and softirq stacks, it's update
is racy unless we hard disable interrupts, which is costly. This
is fine on 32-bit as we don't soft-disable there but not on 64-bit.
Thus rather than fixing 2 in order to implement 1 in some hypothetical
future, let's remove the code completely from 64-bit. In order to avoid
a clutter of ifdef's, we remove the updates from C code completely
during interrupt stack switching, and instead maintain it from the
asm helper that is used to do the stack switching in the first place.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul E. McKenney [Wed, 25 Sep 2013 01:29:11 +0000 (18:29 -0700)]
mm: Place preemption point in do_mlockall() loop
There is a loop in do_mlockall() that lacks a preemption point, which
means that the following can happen on non-preemptible builds of the
kernel. Dave Jones reports:
"My fuzz tester keeps hitting this. Every instance shows the non-irq
stack came in from mlockall. I'm only seeing this on one box, but
that has more ram (8gb) than my other machines, which might explain
it.
INFO: rcu_preempt self-detected stall on CPU { 3} (t=6500 jiffies g=470344 c=470343 q=0)
sending NMI to all CPUs:
NMI backtrace for cpu 3
CPU: 3 PID: 29664 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #32
Call Trace:
lru_add_drain_all+0x15/0x20
SyS_mlockall+0xa5/0x1a0
tracesys+0xdd/0xe2"
This commit addresses this problem by inserting the required preemption
point.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I clearly need to be more aware of Andrew's racing schedule.
* akpm:
MAINTAINERS: update mach-bcm related email address
checkpatch: make extern in .h prototypes quieter
cciss: fix info leak in cciss_ioctl32_passthru()
cpqarray: fix info leak in ida_locked_ioctl()
kernel/reboot.c: re-enable the function of variable reboot_default
audit: fix endless wait in audit_log_start()
revert "memcg, vmscan: integrate soft reclaim tighter with zone shrinking code"
revert "memcg: get rid of soft-limit tree infrastructure"
revert "vmscan, memcg: do softlimit reclaim also for targeted reclaim"
revert "memcg: enhance memcg iterator to support predicates"
revert "memcg: track children in soft limit excess to improve soft limit"
revert "memcg, vmscan: do not attempt soft limit reclaim if it would not scan anything"
revert "memcg: track all children over limit in the root"
revert "memcg, vmscan: do not fall into reclaim-all pass too quickly"
fs/ocfs2/super.c: use a bigger nodestr in ocfs2_dismount_volume
watchdog: update watchdog_thresh properly
watchdog: update watchdog attributes atomically
Dan Carpenter [Tue, 24 Sep 2013 22:27:45 +0000 (15:27 -0700)]
cciss: fix info leak in cciss_ioctl32_passthru()
The arg64 struct has a hole after ->buf_size which isn't cleared. Or if
any of the calls to copy_from_user() fail then that would cause an
information leak as well.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Tue, 24 Sep 2013 22:27:44 +0000 (15:27 -0700)]
cpqarray: fix info leak in ida_locked_ioctl()
The pciinfo struct has a two byte hole after ->dev_fn so stack
information could be leaked to the user.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chuansheng Liu [Tue, 24 Sep 2013 22:27:43 +0000 (15:27 -0700)]
kernel/reboot.c: re-enable the function of variable reboot_default
Commit 1b3a5d02ee07 ("reboot: move arch/x86 reboot= handling to generic
kernel") did some cleanup for reboot= command line, but it made the
reboot_default inoperative.
The default value of variable reboot_default should be 1, and if command
line reboot= is not set, system will use the default reboot mode.
[akpm@linux-foundation.org: fix comment layout] Signed-off-by: Li Fei <fei.li@intel.com> Signed-off-by: liu chuansheng <chuansheng.liu@intel.com> Acked-by: Robin Holt <robinmholt@linux.com> Cc: <stable@vger.kernel.org> [3.11.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit 829199197a43 ("kernel/audit.c: avoid negative sleep
durations") audit emitters will block forever if userspace daemon cannot
handle backlog.
After the timeout the waiting loop turns into busy loop and runs until
daemon dies or returns back to work. This is a minimal patch for that
bug.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Richard Guy Briggs <rgb@redhat.com> Cc: Eric Paris <eparis@redhat.com> Cc: Chuck Anderson <chuck.anderson@oracle.com> Cc: Dan Duval <dan.duval@oracle.com> Cc: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Tue, 24 Sep 2013 22:27:30 +0000 (15:27 -0700)]
watchdog: update watchdog_thresh properly
watchdog_tresh controls how often nmi perf event counter checks per-cpu
hrtimer_interrupts counter and blows up if the counter hasn't changed
since the last check. The counter is updated by per-cpu
watchdog_hrtimer hrtimer which is scheduled with 2/5 watchdog_thresh
period which guarantees that hrtimer is scheduled 2 times per the main
period. Both hrtimer and perf event are started together when the
watchdog is enabled.
So far so good. But...
But what happens when watchdog_thresh is updated from sysctl handler?
proc_dowatchdog will set a new sampling period and hrtimer callback
(watchdog_timer_fn) will use the new value in the next round. The
problem, however, is that nobody tells the perf event that the sampling
period has changed so it is ticking with the period configured when it
has been set up.
This might result in an ear ripping dissonance between perf and hrtimer
parts if the watchdog_thresh is increased. And even worse it might lead
to KABOOM if the watchdog is configured to panic on such a spurious
lockup.
This patch fixes the issue by updating both nmi perf even counter and
hrtimers if the threshold value has changed.
The nmi one is disabled and then reinitialized from scratch. This has
an unpleasant side effect that the allocation of the new event might
fail theoretically so the hard lockup detector would be disabled for
such cpus. On the other hand such a memory allocation failure is very
unlikely because the original event is deallocated right before.
It would be much nicer if we just changed perf event period but there
doesn't seem to be any API to do that right now. It is also unfortunate
that perf_event_alloc uses GFP_KERNEL allocation unconditionally so we
cannot use on_each_cpu() and do the same thing from the per-cpu context.
The update from the current CPU should be safe because
perf_event_disable removes the event atomically before it clears the
per-cpu watchdog_ev so it cannot change anything under running handler
feet.
The hrtimer is simply restarted (thanks to Don Zickus who has pointed
this out) if it is queued because we cannot rely it will fire&adopt to
the new sampling period before a new nmi event triggers (when the
treshold is decreased).
[akpm@linux-foundation.org: the UP version of __smp_call_function_single ended up in the wrong place] Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Don Zickus <dzickus@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Tue, 24 Sep 2013 22:27:29 +0000 (15:27 -0700)]
watchdog: update watchdog attributes atomically
proc_dowatchdog doesn't synchronize multiple callers which might lead to
confusion when two parallel callers might confuse watchdog_enable_all_cpus
resp watchdog_disable_all_cpus (eg watchdog gets enabled even if
watchdog_thresh was set to 0 already).
This patch adds a local mutex which synchronizes callers to the sysctl
handler.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Don Zickus <dzickus@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'bcache' (bcache fixes from Kent Overstreet)
Merge bcache fixes from Kent Overstreet:
"There's fixes for _three_ different data corruption bugs, all of which
were found by users hitting them in the wild.
The first one isn't bcache specific - in 3.11 bcache was switched to
the bio_copy_data in fs/bio.c, and that's when the bug in that code
was discovered, but it's also used by raid1 and pktcdvd. (That was my
code too, so the bug's doubly embarassing given that it was or
should've been just a cut and paste from bcache code. Dunno what
happened there).
Most of these (all the non data corruption bugs, actually) were ready
before the merge window and have been sitting in Jens' tree, but I
don't know what's been up with him lately..."
* emailed patches from Kent Overstreet <kmo@daterainc.com>:
bcache: Fix flushes in writeback mode
bcache: Fix for handling overlapping extents when reading in a btree node
bcache: Fix a shrinker deadlock
bcache: Fix a dumb CPU spinning bug in writeback
bcache: Fix a flush/fua performance bug
bcache: Fix a writeback performance regression
bcache: Correct printf()-style format length modifier
bcache: Fix for when no journal entries are found
bcache: Strip endline when writing the label through sysfs
bcache: Fix a dumb journal discard bug
block: Fix bio_copy_data()
Kent Overstreet [Tue, 24 Sep 2013 06:17:36 +0000 (23:17 -0700)]
bcache: Fix flushes in writeback mode
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Kent Overstreet [Tue, 24 Sep 2013 06:17:35 +0000 (23:17 -0700)]
bcache: Fix for handling overlapping extents when reading in a btree node
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
projects / karo-tx-linux.git / log