Linus Torvalds [Sun, 18 Jun 2017 09:49:12 +0000 (18:49 +0900)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two fixlets for x86:
- Handle WARN_ONs proper with the new UD based WARN implementation
- Disable 1G mappings when 2M mappings are disabled by kmemleak or
debug_pagealloc. Otherwise 1G mappings might still be used,
confusing the debug mechanisms"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
x86/debug: Handle early WARN_ONs proper
Linus Torvalds [Sun, 18 Jun 2017 09:46:51 +0000 (18:46 +0900)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets for timers:
- Two hot-fixes for the alarmtimer based posix timers, which prevent
a nasty DOS by self rescheduling timers. The proper cleanup of that
mess is queued for 4.13
- Make a function static"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Make tick_broadcast_setup_oneshot() static
alarmtimer: Rate limit periodic intervals
alarmtimer: Prevent overflow of relative timers
Linus Torvalds [Sun, 18 Jun 2017 09:45:17 +0000 (18:45 +0900)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two small fixes for the schedulre core:
- Use the proper switch_mm() variant in idle_task_exit() because that
code is not called with interrupts disabled.
- Fix a confusing typo in a printk"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
sched/fair: Fix typo in printk message
Linus Torvalds [Sat, 17 Jun 2017 23:51:35 +0000 (08:51 +0900)]
Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Two LED fixes:
- fix signal source assignment for leds-bcm6328
- revert patch that intended to fix LED behavior on suspend but it
had a side effect preventing suspend at all due to uevent being
sent on trigger removal"
* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Revert "leds: handle suspend/resume in heartbeat trigger"
leds: bcm6328: fix signal source assignment for leds 4 to 7
Linus Torvalds [Sat, 17 Jun 2017 23:39:54 +0000 (08:39 +0900)]
Merge tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small gadget and xhci USB fixes for 4.12-rc6.
Nothing major, but one of the gadget patches does fix a reported oops,
and the xhci ones resolve reported problems. All have been in
linux-next with no reported issues"
* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
usb: xhci: Fix USB 3.1 supported protocol parsing
USB: gadget: fix GPF in gadgetfs
usb: gadget: composite: make sure to reactivate function on unbind
Linus Torvalds [Sat, 17 Jun 2017 23:23:02 +0000 (08:23 +0900)]
Merge tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for an old ceph ->fh_to_* bug from Luis and two timestamp fixups
from Zheng, prompted by the ongoing y2038 work"
* tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client:
ceph: unify inode i_ctime update
ceph: use current_kernel_time() to get request time stamp
ceph: check i_nlink while converting a file handle to dentry
Linus Torvalds [Sat, 17 Jun 2017 08:30:07 +0000 (17:30 +0900)]
Merge branch 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull ufs fixes from Al Viro:
"Fix assorted ufs bugs: a couple of deadlocks, fs corruption in
truncate(), oopsen on tail unpacking and truncate when racing with
vmscan, mild fs corruption (free blocks stats summary buggered, *BSD
fsck would complain and fix), several instances of broken logics
around reserved blocks (starting with "check almost never triggers
when it should" and then there are issues with sufficiently large
UFS2)"
[ Note: ufs hasn't gotten any loving in a long time, because nobody
really seems to use it. These ufs fixes are triggered by people
actually caring now, not some sudden influx of new bugs. - Linus ]
* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs_truncate_blocks(): fix the case when size is in the last direct block
ufs: more deadlock prevention on tail unpacking
ufs: avoid grabbing ->truncate_mutex if possible
ufs_get_locked_page(): make sure we have buffer_heads
ufs: fix s_size/s_dsize users
ufs: fix reserved blocks check
ufs: make ufs_freespace() return signed
ufs: fix logics in "ufs: make fsck -f happy"
Linus Torvalds [Sat, 17 Jun 2017 08:26:53 +0000 (17:26 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes; a leak in mntns_install() caught by Andrei (this
cycle regression) + d_invalidate() softlockup fix - that had been
reported by a bunch of people lately, but the problem is pretty old"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: don't forget to put old mntns in mntns_install
Hang/soft lockup in d_invalidate with simultaneous calls
Linus Torvalds [Fri, 16 Jun 2017 21:53:20 +0000 (06:53 +0900)]
Merge tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix another PCI_ENDPOINT build error (merged for v4.12)
- fix error codes added to config accessors for v4.12
* tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: endpoint: Select CRC32 to fix test build error
PCI: Make error code types consistent in pci_{read,write}_config_*
Linus Torvalds [Fri, 16 Jun 2017 21:49:34 +0000 (06:49 +0900)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
zhongjiang [Fri, 16 Jun 2017 21:02:40 +0000 (14:02 -0700)]
mm: correct the comment when reclaimed pages exceed the scanned pages
Commit e1587a494540 ("mm: vmpressure: fix sending wrong events on
underflow") declared that reclaimed pages exceed the scanned pages due
to the thp reclaim.
That is incorrect because THP will be spilt to normal page and loop
again, which will result in the scanned pages increment.
Andrea Arcangeli [Fri, 16 Jun 2017 21:02:37 +0000 (14:02 -0700)]
userfaultfd: shmem: handle coredumping in handle_userfault()
Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().
shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.
This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.
The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits. Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).
It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).
Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> [4.11+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Rutland [Fri, 16 Jun 2017 21:02:34 +0000 (14:02 -0700)]
mm: numa: avoid waiting on freed migrated pages
In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry. However,
we can race with migrate_misplaced_transhuge_page():
// do_huge_pmd_numa_page // migrate_misplaced_transhuge_page()
// Holds 0 refs on page // Holds 2 refs on page
vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
/* ... */
if (pmd_trans_migrating(*vmf->pmd)) {
page = pmd_page(*vmf->pmd);
spin_unlock(vmf->ptl);
ptl = pmd_lock(mm, pmd);
if (page_count(page) != 2)) {
/* roll back */
}
/* ... */
mlock_migrate_page(new_page, page);
/* ... */
spin_unlock(ptl);
put_page(page);
put_page(page); // page freed here
wait_on_page_locked(page);
goto out;
}
This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions. This has been observed on arm64 KVM guests.
We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().
When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.
Fixes: b8916634b77bffb2 ("mm: Prevent parallel splits during THP migration") Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Steve Capper <steve.capper@arm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Morse [Fri, 16 Jun 2017 21:02:29 +0000 (14:02 -0700)]
mm/memory-failure.c: use compound_head() flags for huge pages
memory_failure() chooses a recovery action function based on the page
flags. For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:
> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed
Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead. This results in the me_huge_page() recovery
action being called:
> Memory failure: 0x9b7969: recovery action for huge page: Delayed
For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.
Fixes: 524fca1e7356 ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages") Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.com Signed-off-by: James Morse <james.morse@arm.com> Tested-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Jun 2017 20:57:54 +0000 (05:57 +0900)]
Merge tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three small fixes for recently merged code:
- remove a spurious WARN_ON when a PCI device has no of_node, it's
allowed in some circumstances for there to be no of_node.
- fix the offset for store EOI MMIOs in the XIVE interrupt
controller.
- fix non-const WARN_ONs which were becoming BUGs due to them losing
BUGFLAG_WARNING in a recent cleanup patch.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Benjamin
Herrenschmidt"
* tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
powerpc/xive: Fix offset for store EOI MMIOs
powerpc/npu-dma: Remove spurious WARN_ON when a PCI device has no of_node
Ingo Molnar [Fri, 16 Jun 2017 19:33:48 +0000 (21:33 +0200)]
Merge tag 'perf-urgent-for-mingo-4.12-20170616' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix probing of precise_ip level for default cycles event, that
got broken recently on x86_64 when its arch code started
considering invalid requesting precise samples when not sampling
(i.e. when attr.sample_period == 0).
This also fixes another problem in s/390 where the precision
probing with sample_period == 0 returned precise_ip > 0, that
then, when setting up the real cycles event (not probing) would
return EOPNOTSUPP for precise_ip > 0 (as determined previously
by probing) and sample_period > 0.
These problems resulted in attr_precise not being set to the
highest precision available on x86.64 when no event was specified,
i.e. the canonical:
perf record ./workload
would end up using attr.precise_ip = 0. As a workaround this would
need to be done:
perf record -e cycles:P ./workload
And on s/390 it would plain not work, requiring using:
perf record -e cycles ./workload
as a workaround. (Arnaldo Carvalho de Melo)
- Fix perf build with ARCH=x86_64, when ARCH should be transformed
into ARCH=x86, just like with the main kernel Makefile and
tools/objtool's, i.e. use SRCARCH. (Jiada Wang)
- Avoid accessing uninitialized data structures when unwinding with
elfutils's libdw, making it more closely mimic libunwind's unwinder.
(Milian Wolff)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Milian Wolff [Fri, 2 Jun 2017 14:37:53 +0000 (16:37 +0200)]
perf unwind: Report module before querying isactivation in dwfl unwind
The PC returned by dwfl_frame_pc() may map into a not-yet-reported
module. We have to report it before we continue unwinding. But when we
query for the isactivation flag in dwfl_frame_pc, libdw will actually do
one more unwinding step internally which can then break and lead to
missed frames or broken stacks.
Linus Torvalds [Fri, 16 Jun 2017 09:45:47 +0000 (18:45 +0900)]
Merge tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A fix from Nic for a race seen in production (including a stable tag).
And while I'm sending you this I'm also sneaking in a trivial new
helper from Bart so that we don't need inter-tree dependencies for the
next merge window"
* tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs:
configfs: Introduce config_item_get_unless_zero()
configfs: Fix race between create_link and configfs_rmdir
Linus Torvalds [Fri, 16 Jun 2017 08:46:47 +0000 (17:46 +0900)]
Merge tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is the main fixes pull for 4.12-rc6, all pretty normal for this
stage, nothing really stands out. The mxsfb one is probably the
largest and it's for a black screen boot problem.
AMD, i915, mgag200, msxfb, tegra fixes"
* tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux:
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
gpu: host1x: Fix error handling
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
drm/radeon: fix "force the UVD DPB into VRAM as well"
drm/i915: Fix GVT-g PVINFO version compatibility check
drm/i915: Fix SKL+ watermarks for 90/270 rotation
drm/i915: Fix scaling check for 90/270 degree plane rotation
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
Linus Torvalds [Fri, 16 Jun 2017 08:38:23 +0000 (17:38 +0900)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I had thought at the time of the last pull request that there wouldn't
be much more to go, but several things just kept trickling in over the
last week.
Instead of just the six patches to bnxt_re that I had anticipated,
there are another five IPoIB patches, two qedr patches, and a few
other miscellaneous patches.
The bnxt_re patches are more lines of diff than I like to submit this
late in the game. That's mostly because of the first two patches in
the series of six. I almost dropped them just because of the lines of
churn, but on a close review, a lot of the churn came from removing
duplicated code sections and consolidating them into callable
routines. I felt like this made the number of lines of change more
acceptable, and they address problems, so I left them. The remainder
of the patches are all small, well contained, and well understood.
These have passed 0day testing, but have not been submitted to
linux-next (but a local merge test with your current master was
without any conflicts).
Summary:
- A fix for fix eea40b8f624 ("infiniband: call ipv6 route lookup via
the stub interface")
- Six patches against bnxt_re...the first two are considerably larger
than I would like, but as they address real issues I went ahead and
submitted them (it also helped that a good deal of the churn was
removing code repeated in multiple places and consolidating it to
one common function)
- Two fixes against qedr that just came in
- One fix against rxe that took a few revisions to get right plus
time to get the proper reviews
- Five late breaking IPoIB fixes
- One late cxgb4 fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
rdma/cxgb4: Fix memory leaks during module exit
IB/ipoib: Fix memory leak in create child syscall
IB/ipoib: Fix access to un-initialized napi struct
IB/ipoib: Delete napi in device uninit default
IB/ipoib: Limit call to free rdma_netdev for capable devices
IB/ipoib: Fix memory leaks for child interfaces priv
rxe: Fix a sleep-in-atomic bug in post_one_send
RDMA/qedr: Add 64KB PAGE_SIZE support to user-space queues
RDMA/qedr: Initialize byte_len in WC of READ and SEND commands
RDMA/bnxt_re: Remove FMR support
RDMA/bnxt_re: Fix RQE posting logic
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
RDMA/bnxt_re: HW workarounds for handling specific conditions
RDMA/bnxt_re: Fixing the Control path command and response handling
IB/addr: Fix setting source address in addr6_resolve()
Linus Torvalds [Fri, 16 Jun 2017 08:30:44 +0000 (17:30 +0900)]
Merge tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Just a single patch to fix an oops in the intel_telemetry_debugfs
module load/unload"
* tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
Linus Torvalds [Fri, 16 Jun 2017 08:13:06 +0000 (17:13 +0900)]
Merge branch 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi fixes from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi_scan: Check DMI structure length
firmware: dmi: Fix permissions of product_family
firmware: dmi_scan: Make dmi_walk and dmi_walk_early return real error codes
firmware: dmi_scan: Look for SMBIOS 3 entry point first
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
When trapped on WARN_ON(), report_bug() is expected to return
BUG_TRAP_TYPE_WARN so the caller will increment NIP by 4 and continue.
The __builtin_constant_p() path of the PPC's WARN_ON()
calls (indirectly) __WARN_FLAGS() which has BUGFLAG_WARNING set,
however the other branch does not which makes report_bug() report a
bug rather than a warning.
Dave Airlie [Fri, 16 Jun 2017 00:01:04 +0000 (10:01 +1000)]
Merge tag 'drm-misc-fixes-2017-06-15' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- dw-hdmi: Fix compilation error if REGMAP_MMIO not selected (Laurent)
- host1x: Fix incorrect return value (Christophe)
- tegra: Shore up idr API usage in tegra staging code (Dmitry)
- mgag200: Always use HiPri mode for G200e4v2 and limit max bandwidth (Mathieu)
- mxsfb: Ensure display can be lit up without bootloader initialization (Fabio)
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Dmitry Osipenko <digetx@gmail.com> Cc: Mathieu Larouche <mathieu.larouche@matrox.com> Cc: Fabio Estevam <fabio.estevam@nxp.com>
* tag 'drm-misc-fixes-2017-06-15' of git://anongit.freedesktop.org/git/drm-misc:
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
gpu: host1x: Fix error handling
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
Dave Airlie [Fri, 16 Jun 2017 00:00:11 +0000 (10:00 +1000)]
Merge branch 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few fixes for 4.12:
- fix a UVD regression on SI
- fix overflow in watermark calcs on large modes
* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
drm/radeon: fix "force the UVD DPB into VRAM as well"
Alan Stern [Tue, 13 Jun 2017 19:23:42 +0000 (15:23 -0400)]
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:
> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
> __dump_stack lib/dump_stack.c:16 [inline]
> dump_stack+0x292/0x395 lib/dump_stack.c:52
> print_address_description+0x78/0x280 mm/kasan/report.c:252
> kasan_report_error mm/kasan/report.c:351 [inline]
> kasan_report+0x230/0x340 mm/kasan/report.c:408
> __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
> __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
> lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
> __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
> _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
> spin_lock include/linux/spinlock.h:299 [inline]
> gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
> set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
> dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
> rh_call_control drivers/usb/core/hcd.c:689 [inline]
> rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
> usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
> usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
> usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
> usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
> usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
> usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
> hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
> hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
> hub_port_connect drivers/usb/core/hub.c:4826 [inline]
> hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
> port_event drivers/usb/core/hub.c:5105 [inline]
> hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
> process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
> process_scheduled_works kernel/workqueue.c:2157 [inline]
> worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
> kthread+0x363/0x440 kernel/kthread.c:231
> ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
> kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
> kmalloc include/linux/slab.h:492 [inline]
> kzalloc include/linux/slab.h:665 [inline]
> dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
> gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
> mount_single+0xf6/0x160 fs/super.c:1192
> gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
> mount_fs+0x9c/0x2d0 fs/super.c:1223
> vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
> vfs_kern_mount fs/namespace.c:2509 [inline]
> do_new_mount fs/namespace.c:2512 [inline]
> do_mount+0x41b/0x2d90 fs/namespace.c:2834
> SYSC_mount fs/namespace.c:3050 [inline]
> SyS_mount+0xb0/0x120 fs/namespace.c:3027
> entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
> slab_free_hook mm/slub.c:1357 [inline]
> slab_free_freelist_hook mm/slub.c:1379 [inline]
> slab_free mm/slub.c:2961 [inline]
> kfree+0xed/0x2b0 mm/slub.c:3882
> put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
> gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
> deactivate_locked_super+0x8d/0xd0 fs/super.c:309
> deactivate_super+0x21e/0x310 fs/super.c:340
> cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
> __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
> task_work_run+0x1a0/0x280 kernel/task_work.c:116
> exit_task_work include/linux/task_work.h:21 [inline]
> do_exit+0x18a8/0x2820 kernel/exit.c:878
> do_group_exit+0x14e/0x420 kernel/exit.c:982
> get_signal+0x784/0x1780 kernel/signal.c:2318
> do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
> exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
> prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
> syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
> entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
> which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
> 1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping: (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100000000000000000000000000000000000000000100170017
> raw: ffffea0000ed3020ffffea0000f5f820ffff88003e80efc00000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
> ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
> ^
> ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================
What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated. The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking. And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.
The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.
include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal. This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.
The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations. The
patch fixes it too.
Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs. It must
use spin_lock_irqsave() instead of spin_lock_irq(). The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Fri, 5 May 2017 18:01:41 +0000 (15:01 -0300)]
drm: mxsfb_crtc: Reset the eLCDIF controller
According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.
Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.
In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.
Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.
Architecturally we should apply a 0x400 offset for these. Not doing
it will break future HW implementations.
The offset of 0 is supposed to remain for "triggers" though not all
sources support both trigger and store EOI, and in P9 specifically,
some sources will treat 0 as a store EOI. But future chips will not.
So this makes us use the properly architected offset which should work
always.
Fixes: 243e25112d06 ("powerpc/xive: Native exploitation of the XIVE interrupt controller") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dmitry Osipenko [Wed, 14 Jun 2017 23:18:25 +0000 (02:18 +0300)]
drm/tegra: Correct idr_alloc() minimum id
The client ID 0 is reserved by the host1x/cdma to mark the timeout timer
work as already been scheduled and context ID is used as the clients one.
This fixes spurious CDMA timeouts.
Andy Lutomirski [Thu, 15 Jun 2017 11:46:00 +0000 (13:46 +0200)]
firmware: dmi_scan: Make dmi_walk and dmi_walk_early return real error codes
Currently they return -1 on error, which will confuse callers if
they try to interpret it as a normal negative error code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org> Signed-off-by: Jean Delvare <jdelvare@suse.de>
Jean Delvare [Thu, 15 Jun 2017 11:46:00 +0000 (13:46 +0200)]
firmware: dmi_scan: Look for SMBIOS 3 entry point first
Since version 3.0.0 of the SMBIOS specification, there can be
multiple entry points in memory, pointing to one or two DMI tables.
If both a 32-bit ("_SM_") entry point and a 64-bit ("_SM3_") entry
point are present, the specification requires that the latter points
to a table which is a super-set of the table pointed to by the
former. Therefore we should give preference to the 64-bit ("_SM3_")
entry point.
However, currently the code is picking the first valid entry point
it finds. Per specification, we should look for a 64-bit ("_SM3_")
entry point first, and if we can't find any, look for a 32-bit
("_SM_" or "_DMI_") entry point. Modify the code to do that.
Andrei Vagin [Fri, 9 Jun 2017 00:32:29 +0000 (17:32 -0700)]
fs: don't forget to put old mntns in mntns_install
Fixes: 4f757f3cbf54 ("make sure that mntns_install() doesn't end up with referral for root") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrei Vagin <avagin@openvz.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 3 Jun 2017 06:20:09 +0000 (07:20 +0100)]
Hang/soft lockup in d_invalidate with simultaneous calls
It's not hard to trigger a bunch of d_invalidate() on the same
dentry in parallel. They end up fighting each other - any
dentry picked for removal by one will be skipped by the rest
and we'll go for the next iteration through the entire
subtree, even if everything is being skipped. Morevoer, we
immediately go back to scanning the subtree. The only thing
we really need is to dissolve all mounts in the subtree and
as soon as we've nothing left to do, we can just unhash the
dentry and bugger off.
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
Linus Torvalds [Thu, 15 Jun 2017 08:51:19 +0000 (17:51 +0900)]
Merge tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert an ACPICA commit from the 4.11 cycle that causes problems
to happen on some systems and add a protection against possible kernel
crashes due to table reference counter imbalance.
Specifics:
- Revert a 4.11 ACPICA change that made assumptions which are not
satisfied on some systems and caused the enumeration of resources
to fail on them (Rafael Wysocki).
- Add a mechanism to prevent tables from being unmapped prematurely
due to reference counter overflows (Lv Zheng)"
* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Revert "ACPICA: Disassembler: Enhance resource descriptor detection"
Linus Torvalds [Thu, 15 Jun 2017 08:47:46 +0000 (17:47 +0900)]
Merge tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These revert a recent cpufreq schedutil governor change that turned
out to be problematic and fix a few minor issues in cpufreq, cpuidle
and the Exynos devfreq drivers.
Specifics:
- Revert a recent cpufreq schedutil governor change that caused some
systems to behave undesirably (Rafael Wysocki).
- Fix a cpufreq conservative governor issue introduced during the
3.10 cycle that prevents it from working as expected in some
situations (Tomasz Wilczyński).
- Fix an error code path in the generic cpuidle driver for DT-based
systems (Christophe Jaillet).
- Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
Krzysztof Kozlowski)"
* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: dt: Add missing 'of_node_put()'
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
Linus Torvalds [Thu, 15 Jun 2017 08:44:41 +0000 (17:44 +0900)]
Merge branch 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
- ifdef-based bandaid for a long-standing issue with HID driver
matching, avoiding regressions in cases where specific driver is not
enabled in kernel .config, from Jiri Kosina
* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: let generic driver yield control iff specific driver has been enabled
Linus Torvalds [Thu, 15 Jun 2017 08:37:40 +0000 (17:37 +0900)]
Merge tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build dependency issues at CEC core with randconfigs
- fix an off by one error at vb2
- a race fix at cec core
- driver fixes at tc358743, sir_ir and rainshadow-cec
* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
[media] cec: race fix: don't return -ENONET in cec_receive()
[media] sir_ir: infinite loop in interrupt handler
[media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
[media] cec: improve MEDIA_CEC_RC dependencies
[media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
[media] rainshadow-cec: Fix missing spin_lock_init()
[media] tc358743: fix register i2c_rd/wr function fix
Al Viro [Thu, 15 Jun 2017 07:57:46 +0000 (03:57 -0400)]
ufs_truncate_blocks(): fix the case when size is in the last direct block
The logics when deciding whether we need to do anything with direct blocks
is broken when new size is within the last direct block. It's better to
find the path to the last byte _not_ to be removed and use that instead
of the path to the beginning of the first block to be freed...
Al Viro [Thu, 15 Jun 2017 04:17:30 +0000 (00:17 -0400)]
ufs: avoid grabbing ->truncate_mutex if possible
tail unpacking is done in a wrong place; the deadlocks galore
is best dealt with by doing that in ->write_iter() (and switching
to iomap, while we are at it), but that's rather painful to
backport. The trouble comes from grabbing pages that cover
the beginning of tail from inside of ufs_new_fragments(); ongoing
pageout of any of those is going to deadlock on ->truncate_mutex
with process that got around to extending the tail holding that
and waiting for page to get unlocked, while ->writepage() on
that page is waiting on ->truncate_mutex.
The thing is, we don't need ->truncate_mutex when the fragment
we are trying to map is within the tail - the damn thing is
allocated (tail can't contain holes).
Let's do a plain lookup and if the fragment is present, we can
just pretend that we'd won the race in almost all cases. The
only exception is a fragment between the end of tail and the
end of block containing tail.
Protect ->i_lastfrag with ->meta_lock - read_seqlock_excl() is
sufficient.
Jia-Ju Bai [Wed, 14 Jun 2017 23:35:31 +0000 (16:35 -0700)]
i40e: Fix a sleep-in-atomic bug
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Thu, 15 Jun 2017 03:32:19 +0000 (23:32 -0400)]
ufs_get_locked_page(): make sure we have buffer_heads
callers rely upon that, but find_lock_page() racing with attempt of
page eviction by memory pressure might have left us with
* try_to_free_buffers() successfully done
* __remove_mapping() failed, leaving the page in our mapping
* find_lock_page() returning an uptodate page with no
buffer_heads attached.
Al Viro [Wed, 14 Jun 2017 20:36:29 +0000 (16:36 -0400)]
ufs: fix s_size/s_dsize users
For UFS2 we need 64bit variants; we even store them in uspi, but
use 32bit ones instead. One wrinkle is in handling of reserved
space - recalculating it every time had been stupid all along, but
now it would become really ugly. Just calculate it once...
net: don't global ICMP rate limit packets originating from loopback
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab73 ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab73 ("net: reduce cycles spend on ICMP replies that gets rate limited") Reported-by: Florian Weimer <fweimer@redhat.com> Reported-by: "H.J. Lu" <hjl.tools@gmail.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 14 Jun 2017 10:29:31 +0000 (13:29 +0300)]
net/act_pedit: fix an error code
I'm reviewing static checker warnings where we do ERR_PTR(0), which is
the same as NULL. I'm pretty sure we intended to return ERR_PTR(-EINVAL)
here. Sometimes these bugs lead to a NULL dereference but I don't
immediately see that problem here.
Fixes: 71d0ed7079df ("net/act_pedit: Support using offset relative to the conventional network headers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Amir Vadai <amir@vadai.me> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Wed, 14 Jun 2017 19:17:32 +0000 (15:17 -0400)]
ufs: fix logics in "ufs: make fsck -f happy"
Storing stats _only_ at new locations is wrong for UFS1; old
locations should always be kept updated. The check for "has
been converted to use of new locations" is also wrong - it
should be "->fs_maxbsize is equal to ->fs_bsize".
Feras Daoud [Wed, 14 Jun 2017 06:59:09 +0000 (09:59 +0300)]
IB/ipoib: Fix memory leak in create child syscall
The flow of creating a new child goes through ipoib_vlan_add
which allocates a new interface and checks the rtnl_lock.
If the lock is taken, restart_syscall will be called to restart
the system call again. In this case we are not releasing the
already allocated interface, causing a leak.
Alex Vesker [Wed, 14 Jun 2017 06:59:08 +0000 (09:59 +0300)]
IB/ipoib: Fix access to un-initialized napi struct
There is no need to re-enable napi since we set the initialized
flag before calling ipoib_ib_dev_stop which will disable napi,
disabling napi twice is harmless in case it was already disabled.
One more reason for this fix is that when using IPoIB new device
driver napi is not added to priv, this can lead to kernel panic
when rn_ops ndo_open fails.
Alex Vesker [Wed, 14 Jun 2017 06:59:07 +0000 (09:59 +0300)]
IB/ipoib: Delete napi in device uninit default
This patch mekas init_default and uninit_default symmetric
with a call to delete napi. Additionally, the uninit_default
gained delete napi call in case of init_default fails.
Fixes: 515ed4f3aab4 ('IB/IPoIB: Separate control and data related initializations') Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Alex Vesker [Wed, 14 Jun 2017 06:59:05 +0000 (09:59 +0300)]
IB/ipoib: Fix memory leaks for child interfaces priv
There is a need to free priv explicitly and not just to release
the device, child priv is freed explicitly on remove flow and this
patch also includes priv free on error flow in P_key creation
and also in add_port.
Fixes: cd565b4b51e5 ('IB/IPoIB: Support acceleration options callbacks') Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Magnus Damm [Wed, 14 Jun 2017 07:15:24 +0000 (16:15 +0900)]
net: update undefined ->ndo_change_mtu() comment
Update ->ndo_change_mtu() callback comment to remove text
about returning error in case of undefined callback. This
change makes the comment match the existing code behavior.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiada Wang [Mon, 10 Apr 2017 03:02:37 +0000 (20:02 -0700)]
perf tools: Fix build with ARCH=x86_64
With commit: 0a943cb10ce78 (tools build: Add HOSTARCH Makefile variable)
when building for ARCH=x86_64, ARCH=x86_64 is passed to perf instead of
ARCH=x86, so the perf build process searchs header files from
tools/arch/x86_64/include, which doesn't exist.
The following build failure is seen:
In file included from util/event.c:2:0:
tools/include/uapi/linux/mman.h:4:27: fatal error: uapi/asm/mman.h: No such file or directory
compilation terminated.
Fix this issue by using SRCARCH instead of ARCH in perf, just like the
main kernel Makefile and tools/objtool's.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Eugeniu Rosca <erosca@de.adit-jv.com> Cc: Jan Stancek <jstancek@redhat.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Rui Teng <rui.teng@linux.vnet.ibm.com> Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 0a943cb10ce7 ("tools build: Add HOSTARCH Makefile variable") Link: http://lkml.kernel.org/r/1491793357-14977-2-git-send-email-jiada_wang@mentor.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf evsel: Fix probing of precise_ip level for default cycles event
Since commit 18e7a45af91a ("perf/x86: Reject non sampling events with
precise_ip") returns -EINVAL for sys_perf_event_open() with an attribute
with (attr.precise_ip > 0 && attr.sample_period == 0), just like is done
in the routine used to probe the max precise level when no events were
passed to 'perf record' or 'perf top', i.e.:
The x86 code, in x86_pmu_hw_config(), which is called all the way from
sys_perf_event_open() did, starting with the aforementioned commit:
/* There's no sense in having PEBS for non sampling events: */
if (!is_sampling_event(event))
return -EINVAL;
Which makes it fail for cycles:ppp, cycles:pp and cycles:p, always using
just the non precise cycles variant.
To make sure that this is the case, I tested it, before this patch,
with:
# perf probe -L x86_pmu_hw_config
<x86_pmu_hw_config@/home/acme/git/linux/arch/x86/events/core.c:0>
0 int x86_pmu_hw_config(struct perf_event *event)
1 {
2 if (event->attr.precise_ip) {
<SNIP>
17 if (event->attr.precise_ip > precise)
18 return -EOPNOTSUPP;
/* There's no sense in having PEBS for non sampling events: */
21 if (!is_sampling_event(event))
22 return -EINVAL;
}
<SNIP>
# perf probe x86_pmu_hw_config:22
Added new events:
probe:x86_pmu_hw_config (on x86_pmu_hw_config:22)
probe:x86_pmu_hw_config_1 (on x86_pmu_hw_config:22)
You can now use it in all perf tools, such as:
perf record -e probe:x86_pmu_hw_config_1 -aR sleep 1
The probe one called from perf_event_attr__set_max_precise_ip() works
the first time, with attr.precise_ip = 3, wit hthe next ones being the
per cpu ones for the cycles:ppp event.
And here is the text from a report and alternative proposed patch by
Thomas-Mich Richter:
---
On s390 the counter and sampling facility do not support a precise IP
skid level and sometimes returns EOPNOTSUPP when structure member
precise_ip in struct perf_event_attr is not set to zero.
On s390 commnd 'perf record -- true' fails with error EOPNOTSUPP. This
happens only when no events are specified on command line.
The functions called are
...
--> perf_evlist__add_default
--> perf_evsel__new_cycles
--> perf_event_attr__set_max_precise_ip
The last function determines the value of structure member precise_ip by
invoking the perf_event_open() system call and checking the return code.
The first successful open is the value for precise_ip.
However the value is determined without setting member sample_period and
indicates no sampling.
On s390 the counter facility and sampling facility are different. The
above procedure determines a precise_ip value of 3 using the counter
facility. Later it uses the sampling facility with a value of 3 and
fails with EOPNOTSUPP.
---
v2: Older compilers (e.g. gcc 4.4.7) don't support referencing members
of unnamed union members in the container struct initialization, so
move from:
v3: We need to reset .sample_period to 0 to let the users of
perf_evsel__new_cycles() to properly setup attr.sample_period or
attr.sample_freq. Reported by Ingo Molnar.
Reported-and-Acked-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com> Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 18e7a45af91a ("perf/x86: Reject non sampling events with precise_ip") Link: http://lkml.kernel.org/n/tip-yv6nnkl7tzqocrm0hl3x7vf1@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
WANG Cong [Tue, 13 Jun 2017 20:36:24 +0000 (13:36 -0700)]
net_sched: move tcf_lock down after gen_replace_estimator()
Laura reported a sleep-in-atomic kernel warning inside
tcf_act_police_init() which calls gen_replace_estimator() with
spinlock protection.
It is not necessary in this case, we already have RTNL lock here
so it is enough to protect concurrent writers. For the reader,
i.e. tcf_act_police(), it needs to make decision based on this
rate estimator, in the worst case we drop more/less packets than
necessary while changing the rate in parallel, it is still acceptable.
Reported-by: Laura Abbott <labbott@redhat.com> Reported-by: Nick Huber <nicholashuber@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yan, Zheng [Thu, 1 Jun 2017 09:08:00 +0000 (17:08 +0800)]
ceph: unify inode i_ctime update
Current __ceph_setattr() can set inode's i_ctime to current_time(),
req->r_stamp or attr->ia_ctime. These time stamps may have minor
differences. It may cause potential problem.
Yan, Zheng [Thu, 1 Jun 2017 08:44:53 +0000 (16:44 +0800)]
ceph: use current_kernel_time() to get request time stamp
ceph uses ktime_get_real_ts() to get request time stamp. In most
other cases, current_kernel_time() is used to get time stamp for
filesystem operations (called by current_time()).
There is granularity difference between ktime_get_real_ts() and
current_kernel_time(). The later one can be up to one jiffy behind
the former one. This can causes inode's ctime to go back.
Luis Henriques [Wed, 17 May 2017 11:21:07 +0000 (12:21 +0100)]
ceph: check i_nlink while converting a file handle to dentry
Converting a file handle to a dentry can be done call after the inode
unlink. This means that __fh_to_dentry() requires an extra check to
verify the number of links is not 0.
The issue can be easily reproduced using xfstest generic/426, which does
something like:
Jia-Ju Bai [Mon, 5 Jun 2017 12:23:40 +0000 (20:23 +0800)]
rxe: Fix a sleep-in-atomic bug in post_one_send
The driver may sleep under a spin lock, and the function call path is:
post_one_send (acquire the lock by spin_lock_irqsave)
init_send_wqe
copy_from_user --> may sleep
There is no flow that makes "qp->is_user" true, and copy_from_user may
cause bug when a non-user pointer is used. So the lines of copy_from_user
and check of "qp->is_user" are removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Acked-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Ram Amrani [Mon, 5 Jun 2017 13:32:27 +0000 (16:32 +0300)]
RDMA/qedr: Add 64KB PAGE_SIZE support to user-space queues
Add 64KB PAGE_SIZE support to user-space CQ, SQ and RQ queues.
De-facto it means that code was added to translate 64KB
pages to smaller 4KB pages that the FW can handle. Otherwise,
the FW would wrap (or jump to the next page) when reaching 4KB
while the user space library will continue on the same large page.
Note that MR code remains as is since the FW supports larger pages
for MRs.
Devesh Sharma [Mon, 22 May 2017 10:15:40 +0000 (03:15 -0700)]
RDMA/bnxt_re: Fix RQE posting logic
This patch adds code to ring RQ Doorbell aggressively
so that the adapter can DMA RQ buffers sooner, instead
of DMA all WQEs in the post_recv WR list together at the
end of the post_recv verb.
Also use spinlock to serialize RQ posting
Somnath Kotur [Mon, 22 May 2017 10:15:36 +0000 (03:15 -0700)]
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
HW stalls out after 0x800000 WQEs are posted for UD QPs.
To workaround this problem, driver will send a modify_qp cmd
to the HW at around the halfway mark(0x400000) so that FW
can accordingly modify the QP context in the HW to prevent this
stall.
This workaround needs to be done for UD, QP1 and Raw Ethertype
packets. Added a counter to keep track of WQEs posted during post_send.
Selvin Xavier [Mon, 22 May 2017 10:15:34 +0000 (03:15 -0700)]
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
If the host buffers are freed before destroying MR in HW,
HW could try accessing these buffers. This could cause a host
crash. Fixing the code to avoid this condition.
Eddie Wai [Wed, 14 Jun 2017 10:26:23 +0000 (03:26 -0700)]
RDMA/bnxt_re: HW workarounds for handling specific conditions
This patch implements the following HW workarounds
1. The SQ depth needs to be augmented by 128 + 1 to avoid running
into an Out of order CQE issue
2. Workaround to handle the problem where the HW fast path engine continues
to access DMA memory in retranmission mode even after the WQE has
already been completed. If the HW reports this condition, driver detects
it and posts a Fence WQE. The driver stops reporting the completions
to stack until it receives completion for Fence WQE.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mario Kleiner [Tue, 13 Jun 2017 05:17:11 +0000 (07:17 +0200)]
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
Commit e6b9a6c84b93
("drm/radeon: Make display watermark calculations more accurate")
made watermark calculations more accurate, but not for > 4k
resolutions on 32-Bit architectures, as it introduced an integer
overflow for those setups and resolutions.
Fix this by proper u64 casting and division.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: e6b9a6c84b93 ("drm/radeon: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Kleiner [Tue, 13 Jun 2017 05:17:10 +0000 (07:17 +0200)]
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
Commit d63c277dc672e0
("drm/amdgpu: Make display watermark calculations more accurate")
made watermark calculations more accurate, but not for > 4k
resolutions on 32-Bit architectures, as it introduced an integer
overflow for those setups and resolutions.
Fix this by proper u64 casting and division.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: d63c277dc672 ("drm/amdgpu: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 18 May 2017 08:31:01 +0000 (10:31 +0200)]
drm/radeon: fix "force the UVD DPB into VRAM as well"
The DPB must be in VRAM, but not in the first segment.
Signed-off-by: Christian König <christian.koenig@amd.com> Tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dan Carpenter [Wed, 14 Jun 2017 09:10:56 +0000 (12:10 +0300)]
Staging: rtl8723bs: fix an error code in isFileReadable()
The caller only cares about zero vs non-zero so this code actually works
fine but we should be returning a negative error code instead of a valid
pointer casted to int.
Mike Gerow [Wed, 14 Jun 2017 10:40:36 +0000 (12:40 +0200)]
video: fbdev: udlfb: drop log level for blanking
Drop log level for blanking from info to debug. Xorg likes to habitually
unblank when already unblanked and this can fill up logs over a long period
of time.
Signed-off-by: Mike Gerow <gerow@google.com> Cc: bernie@plugable.com Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Arnd Bergmann [Wed, 14 Jun 2017 10:40:36 +0000 (12:40 +0200)]
video: fbdev: avoid int-in-bool-context warning
gcc-7 suspects this code might be wrong because we use the
result of a multiplication as a bool:
drivers/video/fbdev/core/fbmon.c: In function 'fb_edid_add_monspecs':
drivers/video/fbdev/core/fbmon.c:1051:84: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
It's actually fine, so let's add a comparison to zero to make
that clear to the compiler too.
projects / karo-tx-linux.git / log