/*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
-#undef CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#define CONFIG_PCI /* enable any pci type devices */
+#define CONFIG_PCI1 /* PCI controller 1 */
+#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#undef CONFIG_RIO
+#undef CONFIG_PCI2
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_FSL_VIA
/*
* When initializing flash, if we cannot find the manufacturer ID,
*/
#define CONFIG_ASSUME_AMD_FLASH
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
-
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00400000
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+
+#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-/*
- * Make sure required options are set
- */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif
#undef CONFIG_CLOCKS_IN_MHZ
-
/*
* Local Bus Definitions
*/
* Use GPCM = BRx[24:26] = 000
* Valid = BRx[31] = 1
*
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
*
* OR0, OR1:
* Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
* TRLX = use relaxed timing = ORx[29] = 1
* EAD = use external address latch delay = OR[31] = 1
*
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
*/
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
+#define CONFIG_SYS_BOOT_BLOCK 0xff000000 /* boot TLB block */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff801001
-#define CFG_BR1_PRELIM 0xff001001
+#define CONFIG_SYS_BR0_PRELIM 0xff801001
+#define CONFIG_SYS_BR1_PRELIM 0xff001001
-#define CFG_OR0_PRELIM 0xff806e65
-#define CFG_OR1_PRELIM 0xff806e65
+#define CONFIG_SYS_OR0_PRELIM 0xff806e65
+#define CONFIG_SYS_OR1_PRELIM 0xff806e65
-#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
/*
* SDRAM on the Local Bus
*/
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
+#define CONFIG_SYS_LBC_CACHE_SIZE 64
+#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 /* Localbus non-cacheable */
+#define CONFIG_SYS_LBC_NONCACHE_SIZE 64
+
+#define CONFIG_SYS_LBC_SDRAM_BASE CONFIG_SYS_LBC_CACHE_BASE /* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR2, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
* SDRAM for MSEL = BR2[24:26] = 011
* Valid = BR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
*
- * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
* FIXME: the top 17 bits of BR2.
*/
-#define CFG_BR2_PRELIM 0xf0001861
+#define CONFIG_SYS_BR2_PRELIM 0xf0001861
/*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* For OR2, need:
* 64MB mask for AM, OR2[0:7] = 1111 1100
* XAM, OR2[17:18] = 11
* 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
+ * 13 rows OR2[23-25] = 100
* EAD set for extra time OR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
-#define CFG_OR2_PRELIM 0xfc006901
+#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
-
-/*
- * LSDMR masks
- */
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
+#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
* Common settings for all Local Bus SDRAM commands.
* At run time, either BSMA1516 (for CPU 1.1)
- * or BSMA1617 (for CPU 1.0) (old)
+ * or BSMA1617 (for CPU 1.0) (old)
* is OR'ed in too.
*/
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
- | CFG_LBC_LSDMR_PRETOACT7 \
- | CFG_LBC_LSDMR_ACTTORW7 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC4 \
- | CFG_LBC_LSDMR_CL3 \
- | CFG_LBC_LSDMR_RFEN \
+#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
+ | LSDMR_PRETOACT7 \
+ | LSDMR_ACTTORW7 \
+ | LSDMR_BL8 \
+ | LSDMR_WRC4 \
+ | LSDMR_CL3 \
+ | LSDMR_RFEN \
)
/*
* Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
* port-size = 8-bits = BR[19:20] = 01
* no parity checking = BR[21:22] = 00
- * GPMC for MSEL = BR[24:26] = 000
- * Valid = BR[31] = 1
+ * GPMC for MSEL = BR[24:26] = 000
+ * Valid = BR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
*
* For OR3, need:
- * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
+ * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
* disable buffer ctrl OR[19] = 0
- * CSNT OR[20] = 1
- * ACS OR[21:22] = 11
- * XACS OR[23] = 1
+ * CSNT OR[20] = 1
+ * ACS OR[21:22] = 11
+ * XACS OR[23] = 1
* SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
- * SETA OR[28] = 0
- * TRLX OR[29] = 1
- * EHTR OR[30] = 1
- * EAD extra time OR[31] = 1
+ * SETA OR[28] = 0
+ * TRLX OR[29] = 1
+ * EHTR OR[30] = 1
+ * EAD extra time OR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
+#define CONFIG_FSL_CADMUS
+
#define CADMUS_BASE_ADDR 0xf8000000
-#define CFG_BR3_PRELIM 0xf8000801
-#define CFG_OR3_PRELIM 0xfff00ff7
+#define CONFIG_SYS_BR3_PRELIM 0xf8000801
+#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_INDEX 2
+#define CONFIG_CONS_INDEX 2
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define OF_CPU "PowerPC,8548@0"
-#define OF_SOC "soc8548@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8548@e0000000/serial@4600"
+#define CONFIG_SYS_64BIT_VSPRINTF 1
+#define CONFIG_SYS_64BIT_STRTOUL 1
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR 0x57
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_CCID
+#define CONFIG_SYS_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI_VIRT 0x80000000 /* 1G PCI TLB */
+#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */
+
+#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
+#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#ifdef CONFIG_PCI2
+#define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI2_IO_VIRT 0xe2800000
+#define CONFIG_SYS_PCI2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xe2800000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
+#endif
+
+#ifdef CONFIG_PCIE1
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xe3000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#endif
-#define CFG_PCI2_MEM_BASE 0xa0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2100000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#ifdef CONFIG_RIO
+/*
+ * RapidIO MMU
+ */
+#define CONFIG_SYS_RIO_MEM_VIRT 0xC0000000
+#define CONFIG_SYS_RIO_MEM_BUS 0xC0000000
+#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */
+#endif
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_85XX_PCI2
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC85XX_TSEC1 1
-#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0"
-#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1"
-#define CONFIG_MPC85XX_TSEC3 1
-#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC2"
-#undef CONFIG_MPC85XX_TSEC4
-#define CONFIG_MPC85XX_TSEC4_NAME "eTSEC3"
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC2"
+#define CONFIG_TSEC4
+#define CONFIG_TSEC4_NAME "eTSEC3"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
-
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
-#define CFG_ENV_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII)
+ #define CONFIG_CMD_PCI
#endif
-#include <cmd_confdefs.h>
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
+#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
-#define CONFIG_IPADDR 192.168.1.253
+#define CONFIG_IPADDR 192.168.1.253
-#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH /nfsroot
-#define CONFIG_BOOTFILE your.uImage
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE 8548cds/uImage.uboot
+#define CONFIG_UBOOTPATH 8548cds/u-boot.bin /* TFTP server */
-#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
+#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS1\0" \
- "ramdiskaddr=600000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=your.fdt.dtb\0"
-
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "consoledev=ttyS1\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=mpc8548cds.dtb\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff