* this program; if not, write to the Free Software Foundation, Inc., 59
* Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*
- * The full GNU General Public License is iin this distribution in the
- * file called COPYING.
+ * The full GNU General Public License is in this distribution in the file
+ * called COPYING.
*
* Documentation: ARM DDI 0196G == PL080
- * Documentation: ARM DDI 0218E == PL081
+ * Documentation: ARM DDI 0218E == PL081
*
- * PL080 & PL081 both have 16 sets of DMA signals that can be routed to
- * any channel.
+ * PL080 & PL081 both have 16 sets of DMA signals that can be routed to any
+ * channel.
*
* The PL080 has 8 channels available for simultaneous use, and the PL081
* has only two channels. So on these DMA controllers the number of channels
*
* ASSUMES default (little) endianness for DMA transfers
*
- * Only DMAC flow control is implemented
+ * The PL08x has two flow control settings:
+ * - DMAC flow control: the transfer size defines the number of transfers
+ * which occur for the current LLI entry, and the DMAC raises TC at the
+ * end of every LLI entry. Observed behaviour shows the DMAC listening
+ * to both the BREQ and SREQ signals (contrary to documented),
+ * transferring data if either is active. The LBREQ and LSREQ signals
+ * are ignored.
+ *
+ * - Peripheral flow control: the transfer size is ignored (and should be
+ * zero). The data is transferred from the current LLI entry, until
+ * after the final transfer signalled by LBREQ or LSREQ. The DMAC
+ * will then move to the next LLI entry.
+ *
+ * Only the former works sanely with scatter lists, so we only implement
+ * the DMAC flow control method. However, peripherals which use the LBREQ
+ * and LSREQ signals (eg, MMCI) are unable to use this mode, which through
+ * these hardware restrictions prevents them from using scatter DMA.
*
* Global TODO:
* - Break out common code from arch/arm/mach-s3c64xx and share
#include <linux/device.h>
#include <linux/init.h>
#include <linux/module.h>
-#include <linux/pci.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include <linux/delay.h>
#include <linux/dmapool.h>
-#include <linux/amba/bus.h>
#include <linux/dmaengine.h>
+#include <linux/amba/bus.h>
#include <linux/amba/pl08x.h>
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <asm/hardware/pl080.h>
-#include <asm/dma.h>
-#include <asm/mach/dma.h>
-#include <asm/atomic.h>
-#include <asm/processor.h>
-#include <asm/cacheflush.h>
#define DRIVER_NAME "pl08xdmac"
/**
- * struct vendor_data - vendor-specific config parameters
- * for PL08x derivates
- * @name: the name of this specific variant
+ * struct vendor_data - vendor-specific config parameters for PL08x derivatives
* @channels: the number of channels available in this variant
- * @dualmaster: whether this version supports dual AHB masters
- * or not.
+ * @dualmaster: whether this version supports dual AHB masters or not.
*/
struct vendor_data {
- char *name;
u8 channels;
bool dualmaster;
};
/*
* PL08X private data structures
- * An LLI struct - see pl08x TRM
- * Note that next uses bit[0] as a bus bit,
- * start & end do not - their bus bit info
- * is in cctl
+ * An LLI struct - see PL08x TRM. Note that next uses bit[0] as a bus bit,
+ * start & end do not - their bus bit info is in cctl. Also note that these
+ * are fixed 32-bit quantities.
*/
-struct lli {
- dma_addr_t src;
- dma_addr_t dst;
- dma_addr_t next;
+struct pl08x_lli {
+ u32 src;
+ u32 dst;
+ u32 lli;
u32 cctl;
};
* @phy_chans: array of data for the physical channels
* @pool: a pool for the LLI descriptors
* @pool_ctr: counter of LLIs in the pool
+ * @lli_buses: bitmask to or in to LLI pointer selecting AHB port for LLI fetches
+ * @mem_buses: set to indicate memory transfers on AHB2.
* @lock: a spinlock for this struct
*/
struct pl08x_driver_data {
struct dma_device memcpy;
void __iomem *base;
struct amba_device *adev;
- struct vendor_data *vd;
+ const struct vendor_data *vd;
struct pl08x_platform_data *pd;
struct pl08x_phy_chan *phy_chans;
struct dma_pool *pool;
int pool_ctr;
+ u8 lli_buses;
+ u8 mem_buses;
spinlock_t lock;
};
/* Size (bytes) of each LLI buffer allocated for one transfer */
# define PL08X_LLI_TSFR_SIZE 0x2000
-/* Maximimum times we call dma_pool_alloc on this pool without freeing */
+/* Maximum times we call dma_pool_alloc on this pool without freeing */
#define PL08X_MAX_ALLOCS 0x40
-#define MAX_NUM_TSFR_LLIS (PL08X_LLI_TSFR_SIZE/sizeof(struct lli))
+#define MAX_NUM_TSFR_LLIS (PL08X_LLI_TSFR_SIZE/sizeof(struct pl08x_lli))
#define PL08X_ALIGN 8
static inline struct pl08x_dma_chan *to_pl08x_chan(struct dma_chan *chan)
return container_of(chan, struct pl08x_dma_chan, chan);
}
+static inline struct pl08x_txd *to_pl08x_txd(struct dma_async_tx_descriptor *tx)
+{
+ return container_of(tx, struct pl08x_txd, tx);
+}
+
/*
* Physical channel handling
*/
/*
* Set the initial DMA register values i.e. those for the first LLI
- * The next lli pointer and the configuration interrupt bit have
- * been set when the LLIs were constructed
+ * The next LLI pointer and the configuration interrupt bit have
+ * been set when the LLIs were constructed. Poke them into the hardware
+ * and start the transfer.
*/
-static void pl08x_set_cregs(struct pl08x_driver_data *pl08x,
- struct pl08x_phy_chan *ch)
+static void pl08x_start_txd(struct pl08x_dma_chan *plchan,
+ struct pl08x_txd *txd)
{
- /* Wait for channel inactive */
- while (pl08x_phy_channel_busy(ch))
- ;
-
- dev_vdbg(&pl08x->adev->dev,
- "WRITE channel %d: csrc=%08x, cdst=%08x, "
- "cctl=%08x, clli=%08x, ccfg=%08x\n",
- ch->id,
- ch->csrc,
- ch->cdst,
- ch->cctl,
- ch->clli,
- ch->ccfg);
-
- writel(ch->csrc, ch->base + PL080_CH_SRC_ADDR);
- writel(ch->cdst, ch->base + PL080_CH_DST_ADDR);
- writel(ch->clli, ch->base + PL080_CH_LLI);
- writel(ch->cctl, ch->base + PL080_CH_CONTROL);
- writel(ch->ccfg, ch->base + PL080_CH_CONFIG);
-}
-
-static inline void pl08x_config_phychan_for_txd(struct pl08x_dma_chan *plchan)
-{
- struct pl08x_channel_data *cd = plchan->cd;
+ struct pl08x_driver_data *pl08x = plchan->host;
struct pl08x_phy_chan *phychan = plchan->phychan;
- struct pl08x_txd *txd = plchan->at;
-
- /* Copy the basic control register calculated at transfer config */
- phychan->csrc = txd->csrc;
- phychan->cdst = txd->cdst;
- phychan->clli = txd->clli;
- phychan->cctl = txd->cctl;
-
- /* Assign the signal to the proper control registers */
- phychan->ccfg = cd->ccfg;
- phychan->ccfg &= ~PL080_CONFIG_SRC_SEL_MASK;
- phychan->ccfg &= ~PL080_CONFIG_DST_SEL_MASK;
- /* If it wasn't set from AMBA, ignore it */
- if (txd->direction == DMA_TO_DEVICE)
- /* Select signal as destination */
- phychan->ccfg |=
- (phychan->signal << PL080_CONFIG_DST_SEL_SHIFT);
- else if (txd->direction == DMA_FROM_DEVICE)
- /* Select signal as source */
- phychan->ccfg |=
- (phychan->signal << PL080_CONFIG_SRC_SEL_SHIFT);
- /* Always enable error interrupts */
- phychan->ccfg |= PL080_CONFIG_ERR_IRQ_MASK;
- /* Always enable terminal interrupts */
- phychan->ccfg |= PL080_CONFIG_TC_IRQ_MASK;
-}
-
-/*
- * Enable the DMA channel
- * Assumes all other configuration bits have been set
- * as desired before this code is called
- */
-static void pl08x_enable_phy_chan(struct pl08x_driver_data *pl08x,
- struct pl08x_phy_chan *ch)
-{
+ struct pl08x_lli *lli = &txd->llis_va[0];
u32 val;
- /*
- * Do not access config register until channel shows as disabled
- */
- while (readl(pl08x->base + PL080_EN_CHAN) & (1 << ch->id))
- ;
+ plchan->at = txd;
- /*
- * Do not access config register until channel shows as inactive
- */
- val = readl(ch->base + PL080_CH_CONFIG);
+ /* Wait for channel inactive */
+ while (pl08x_phy_channel_busy(phychan))
+ cpu_relax();
+
+ dev_vdbg(&pl08x->adev->dev,
+ "WRITE channel %d: csrc=0x%08x, cdst=0x%08x, "
+ "clli=0x%08x, cctl=0x%08x, ccfg=0x%08x\n",
+ phychan->id, lli->src, lli->dst, lli->lli, lli->cctl,
+ txd->ccfg);
+
+ writel(lli->src, phychan->base + PL080_CH_SRC_ADDR);
+ writel(lli->dst, phychan->base + PL080_CH_DST_ADDR);
+ writel(lli->lli, phychan->base + PL080_CH_LLI);
+ writel(lli->cctl, phychan->base + PL080_CH_CONTROL);
+ writel(txd->ccfg, phychan->base + PL080_CH_CONFIG);
+
+ /* Enable the DMA channel */
+ /* Do not access config register until channel shows as disabled */
+ while (readl(pl08x->base + PL080_EN_CHAN) & (1 << phychan->id))
+ cpu_relax();
+
+ /* Do not access config register until channel shows as inactive */
+ val = readl(phychan->base + PL080_CH_CONFIG);
while ((val & PL080_CONFIG_ACTIVE) || (val & PL080_CONFIG_ENABLE))
- val = readl(ch->base + PL080_CH_CONFIG);
+ val = readl(phychan->base + PL080_CH_CONFIG);
- writel(val | PL080_CONFIG_ENABLE, ch->base + PL080_CH_CONFIG);
+ writel(val | PL080_CONFIG_ENABLE, phychan->base + PL080_CH_CONFIG);
}
/*
- * Overall DMAC remains enabled always.
- *
- * Disabling individual channels could lose data.
+ * Pause the channel by setting the HALT bit.
*
- * Disable the peripheral DMA after disabling the DMAC
- * in order to allow the DMAC FIFO to drain, and
- * hence allow the channel to show inactive
+ * For M->P transfers, pause the DMAC first and then stop the peripheral -
+ * the FIFO can only drain if the peripheral is still requesting data.
+ * (note: this can still timeout if the DMAC FIFO never drains of data.)
*
+ * For P->M transfers, disable the peripheral first to stop it filling
+ * the DMAC FIFO, and then pause the DMAC.
*/
static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
{
u32 val;
+ int timeout;
/* Set the HALT bit and wait for the FIFO to drain */
val = readl(ch->base + PL080_CH_CONFIG);
writel(val, ch->base + PL080_CH_CONFIG);
/* Wait for channel inactive */
- while (pl08x_phy_channel_busy(ch))
- ;
+ for (timeout = 1000; timeout; timeout--) {
+ if (!pl08x_phy_channel_busy(ch))
+ break;
+ udelay(1);
+ }
+ if (pl08x_phy_channel_busy(ch))
+ pr_err("pl08x: channel%u timeout waiting for pause\n", ch->id);
}
static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
}
-/* Stops the channel */
-static void pl08x_stop_phy_chan(struct pl08x_phy_chan *ch)
+/*
+ * pl08x_terminate_phy_chan() stops the channel, clears the FIFO and
+ * clears any pending interrupt status. This should not be used for
+ * an on-going transfer, but as a method of shutting down a channel
+ * (eg, when it's no longer used) or terminating a transfer.
+ */
+static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
{
- u32 val;
+ u32 val = readl(ch->base + PL080_CH_CONFIG);
- pl08x_pause_phy_chan(ch);
+ val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK);
- /* Disable channel */
- val = readl(ch->base + PL080_CH_CONFIG);
- val &= ~PL080_CONFIG_ENABLE;
- val &= ~PL080_CONFIG_ERR_IRQ_MASK;
- val &= ~PL080_CONFIG_TC_IRQ_MASK;
writel(val, ch->base + PL080_CH_CONFIG);
+
+ writel(1 << ch->id, pl08x->base + PL080_ERR_CLEAR);
+ writel(1 << ch->id, pl08x->base + PL080_TC_CLEAR);
}
static inline u32 get_bytes_in_cctl(u32 cctl)
static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
{
struct pl08x_phy_chan *ch;
- struct pl08x_txd *txdi = NULL;
struct pl08x_txd *txd;
unsigned long flags;
- u32 bytes = 0;
+ size_t bytes = 0;
spin_lock_irqsave(&plchan->lock, flags);
-
ch = plchan->phychan;
txd = plchan->at;
/*
- * Next follow the LLIs to get the number of pending bytes in the
- * currently active transaction.
+ * Follow the LLIs to get the number of remaining
+ * bytes in the currently active transaction.
*/
if (ch && txd) {
- struct lli *llis_va = txd->llis_va;
- struct lli *llis_bus = (struct lli *) txd->llis_bus;
- u32 clli = readl(ch->base + PL080_CH_LLI);
+ u32 clli = readl(ch->base + PL080_CH_LLI) & ~PL080_LLI_LM_AHB2;
- /* First get the bytes in the current active LLI */
+ /* First get the remaining bytes in the active transfer */
bytes = get_bytes_in_cctl(readl(ch->base + PL080_CH_CONTROL));
if (clli) {
- int i = 0;
+ struct pl08x_lli *llis_va = txd->llis_va;
+ dma_addr_t llis_bus = txd->llis_bus;
+ int index;
+
+ BUG_ON(clli < llis_bus || clli >= llis_bus +
+ sizeof(struct pl08x_lli) * MAX_NUM_TSFR_LLIS);
+
+ /*
+ * Locate the next LLI - as this is an array,
+ * it's simple maths to find.
+ */
+ index = (clli - llis_bus) / sizeof(struct pl08x_lli);
- /* Forward to the LLI pointed to by clli */
- while ((clli != (u32) &(llis_bus[i])) &&
- (i < MAX_NUM_TSFR_LLIS))
- i++;
+ for (; index < MAX_NUM_TSFR_LLIS; index++) {
+ bytes += get_bytes_in_cctl(llis_va[index].cctl);
- while (clli) {
- bytes += get_bytes_in_cctl(llis_va[i].cctl);
/*
- * A clli of 0x00000000 will terminate the
- * LLI list
+ * A LLI pointer of 0 terminates the LLI list
*/
- clli = llis_va[i].next;
- i++;
+ if (!llis_va[index].lli)
+ break;
}
}
}
/* Sum up all queued transactions */
- if (!list_empty(&plchan->desc_list)) {
- list_for_each_entry(txdi, &plchan->desc_list, node) {
+ if (!list_empty(&plchan->pend_list)) {
+ struct pl08x_txd *txdi;
+ list_for_each_entry(txdi, &plchan->pend_list, node) {
bytes += txdi->len;
}
-
}
spin_unlock_irqrestore(&plchan->lock, flags);
/*
* Allocate a physical channel for a virtual channel
+ *
+ * Try to locate a physical channel to be used for this transfer. If all
+ * are taken return NULL and the requester will have to cope by using
+ * some fallback PIO mode or retrying later.
*/
static struct pl08x_phy_chan *
pl08x_get_phy_channel(struct pl08x_driver_data *pl08x,
unsigned long flags;
int i;
- /*
- * Try to locate a physical channel to be used for
- * this transfer. If all are taken return NULL and
- * the requester will have to cope by using some fallback
- * PIO mode or retrying later.
- */
for (i = 0; i < pl08x->vd->channels; i++) {
ch = &pl08x->phy_chans[i];
{
unsigned long flags;
+ spin_lock_irqsave(&ch->lock, flags);
+
/* Stop the channel and clear its interrupts */
- pl08x_stop_phy_chan(ch);
- writel((1 << ch->id), pl08x->base + PL080_ERR_CLEAR);
- writel((1 << ch->id), pl08x->base + PL080_TC_CLEAR);
+ pl08x_terminate_phy_chan(pl08x, ch);
/* Mark it as free */
- spin_lock_irqsave(&ch->lock, flags);
ch->serving = NULL;
spin_unlock_irqrestore(&ch->lock, flags);
}
}
static inline u32 pl08x_cctl_bits(u32 cctl, u8 srcwidth, u8 dstwidth,
- u32 tsize)
+ size_t tsize)
{
u32 retbits = cctl;
- /* Remove all src, dst and transfersize bits */
+ /* Remove all src, dst and transfer size bits */
retbits &= ~PL080_CONTROL_DWIDTH_MASK;
retbits &= ~PL080_CONTROL_SWIDTH_MASK;
retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
return retbits;
}
+struct pl08x_lli_build_data {
+ struct pl08x_txd *txd;
+ struct pl08x_driver_data *pl08x;
+ struct pl08x_bus_data srcbus;
+ struct pl08x_bus_data dstbus;
+ size_t remainder;
+};
+
/*
- * Autoselect a master bus to use for the transfer
- * this prefers the destination bus if both available
- * if fixed address on one bus the other will be chosen
+ * Autoselect a master bus to use for the transfer this prefers the
+ * destination bus if both available if fixed address on one bus the
+ * other will be chosen
*/
-void pl08x_choose_master_bus(struct pl08x_bus_data *src_bus,
- struct pl08x_bus_data *dst_bus, struct pl08x_bus_data **mbus,
- struct pl08x_bus_data **sbus, u32 cctl)
+static void pl08x_choose_master_bus(struct pl08x_lli_build_data *bd,
+ struct pl08x_bus_data **mbus, struct pl08x_bus_data **sbus, u32 cctl)
{
if (!(cctl & PL080_CONTROL_DST_INCR)) {
- *mbus = src_bus;
- *sbus = dst_bus;
+ *mbus = &bd->srcbus;
+ *sbus = &bd->dstbus;
} else if (!(cctl & PL080_CONTROL_SRC_INCR)) {
- *mbus = dst_bus;
- *sbus = src_bus;
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
} else {
- if (dst_bus->buswidth == 4) {
- *mbus = dst_bus;
- *sbus = src_bus;
- } else if (src_bus->buswidth == 4) {
- *mbus = src_bus;
- *sbus = dst_bus;
- } else if (dst_bus->buswidth == 2) {
- *mbus = dst_bus;
- *sbus = src_bus;
- } else if (src_bus->buswidth == 2) {
- *mbus = src_bus;
- *sbus = dst_bus;
+ if (bd->dstbus.buswidth == 4) {
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
+ } else if (bd->srcbus.buswidth == 4) {
+ *mbus = &bd->srcbus;
+ *sbus = &bd->dstbus;
+ } else if (bd->dstbus.buswidth == 2) {
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
+ } else if (bd->srcbus.buswidth == 2) {
+ *mbus = &bd->srcbus;
+ *sbus = &bd->dstbus;
} else {
- /* src_bus->buswidth == 1 */
- *mbus = dst_bus;
- *sbus = src_bus;
+ /* bd->srcbus.buswidth == 1 */
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
}
}
}
/*
- * Fills in one LLI for a certain transfer descriptor
- * and advance the counter
+ * Fills in one LLI for a certain transfer descriptor and advance the counter
*/
-int pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
- struct pl08x_txd *txd, int num_llis, int len,
- u32 cctl, u32 *remainder)
+static void pl08x_fill_lli_for_desc(struct pl08x_lli_build_data *bd,
+ int num_llis, int len, u32 cctl)
{
- struct lli *llis_va = txd->llis_va;
- struct lli *llis_bus = (struct lli *) txd->llis_bus;
+ struct pl08x_lli *llis_va = bd->txd->llis_va;
+ dma_addr_t llis_bus = bd->txd->llis_bus;
BUG_ON(num_llis >= MAX_NUM_TSFR_LLIS);
- llis_va[num_llis].cctl = cctl;
- llis_va[num_llis].src = txd->srcbus.addr;
- llis_va[num_llis].dst = txd->dstbus.addr;
-
- /*
- * On versions with dual masters, you can optionally AND on
- * PL080_LLI_LM_AHB2 to the LLI to tell the hardware to read
- * in new LLIs with that controller, but we always try to
- * choose AHB1 to point into memory. The idea is to have AHB2
- * fixed on the peripheral and AHB1 messing around in the
- * memory. So we don't manipulate this bit currently.
- */
-
- llis_va[num_llis].next =
- (dma_addr_t)((u32) &(llis_bus[num_llis + 1]));
+ llis_va[num_llis].cctl = cctl;
+ llis_va[num_llis].src = bd->srcbus.addr;
+ llis_va[num_llis].dst = bd->dstbus.addr;
+ llis_va[num_llis].lli = llis_bus + (num_llis + 1) * sizeof(struct pl08x_lli);
+ if (bd->pl08x->lli_buses & PL08X_AHB2)
+ llis_va[num_llis].lli |= PL080_LLI_LM_AHB2;
if (cctl & PL080_CONTROL_SRC_INCR)
- txd->srcbus.addr += len;
+ bd->srcbus.addr += len;
if (cctl & PL080_CONTROL_DST_INCR)
- txd->dstbus.addr += len;
+ bd->dstbus.addr += len;
- *remainder -= len;
+ BUG_ON(bd->remainder < len);
- return num_llis + 1;
+ bd->remainder -= len;
}
/*
- * Return number of bytes to fill to boundary, or len
+ * Return number of bytes to fill to boundary, or len.
+ * This calculation works for any value of addr.
*/
-static inline u32 pl08x_pre_boundary(u32 addr, u32 len)
+static inline size_t pl08x_pre_boundary(u32 addr, size_t len)
{
- u32 boundary;
+ size_t boundary_len = PL08X_BOUNDARY_SIZE -
+ (addr & (PL08X_BOUNDARY_SIZE - 1));
- boundary = ((addr >> PL08X_BOUNDARY_SHIFT) + 1)
- << PL08X_BOUNDARY_SHIFT;
-
- if (boundary < addr + len)
- return boundary - addr;
- else
- return len;
+ return min(boundary_len, len);
}
/*
static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
struct pl08x_txd *txd)
{
- struct pl08x_channel_data *cd = txd->cd;
struct pl08x_bus_data *mbus, *sbus;
- u32 remainder;
+ struct pl08x_lli_build_data bd;
int num_llis = 0;
u32 cctl;
- int max_bytes_per_lli;
- int total_bytes = 0;
- struct lli *llis_va;
- struct lli *llis_bus;
-
- if (!txd) {
- dev_err(&pl08x->adev->dev, "%s no descriptor\n", __func__);
- return 0;
- }
+ size_t max_bytes_per_lli;
+ size_t total_bytes = 0;
+ struct pl08x_lli *llis_va;
txd->llis_va = dma_pool_alloc(pl08x->pool, GFP_NOWAIT,
&txd->llis_bus);
pl08x->pool_ctr++;
- /*
- * Initialize bus values for this transfer
- * from the passed optimal values
- */
- if (!cd) {
- dev_err(&pl08x->adev->dev, "%s no channel data\n", __func__);
- return 0;
- }
-
- /* Get the default CCTL from the platform data */
- cctl = cd->cctl;
+ /* Get the default CCTL */
+ cctl = txd->cctl;
- /*
- * On the PL080 we have two bus masters and we
- * should select one for source and one for
- * destination. We try to use AHB2 for the
- * bus which does not increment (typically the
- * peripheral) else we just choose something.
- */
- cctl &= ~(PL080_CONTROL_DST_AHB2 | PL080_CONTROL_SRC_AHB2);
- if (pl08x->vd->dualmaster) {
- if (cctl & PL080_CONTROL_SRC_INCR)
- /* Source increments, use AHB2 for destination */
- cctl |= PL080_CONTROL_DST_AHB2;
- else if (cctl & PL080_CONTROL_DST_INCR)
- /* Destination increments, use AHB2 for source */
- cctl |= PL080_CONTROL_SRC_AHB2;
- else
- /* Just pick something, source AHB1 dest AHB2 */
- cctl |= PL080_CONTROL_DST_AHB2;
- }
+ bd.txd = txd;
+ bd.pl08x = pl08x;
+ bd.srcbus.addr = txd->src_addr;
+ bd.dstbus.addr = txd->dst_addr;
/* Find maximum width of the source bus */
- txd->srcbus.maxwidth =
+ bd.srcbus.maxwidth =
pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_SWIDTH_MASK) >>
PL080_CONTROL_SWIDTH_SHIFT);
/* Find maximum width of the destination bus */
- txd->dstbus.maxwidth =
+ bd.dstbus.maxwidth =
pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_DWIDTH_MASK) >>
PL080_CONTROL_DWIDTH_SHIFT);
/* Set up the bus widths to the maximum */
- txd->srcbus.buswidth = txd->srcbus.maxwidth;
- txd->dstbus.buswidth = txd->dstbus.maxwidth;
+ bd.srcbus.buswidth = bd.srcbus.maxwidth;
+ bd.dstbus.buswidth = bd.dstbus.maxwidth;
dev_vdbg(&pl08x->adev->dev,
"%s source bus is %d bytes wide, dest bus is %d bytes wide\n",
- __func__, txd->srcbus.buswidth, txd->dstbus.buswidth);
+ __func__, bd.srcbus.buswidth, bd.dstbus.buswidth);
/*
* Bytes transferred == tsize * MIN(buswidths), not max(buswidths)
*/
- max_bytes_per_lli = min(txd->srcbus.buswidth, txd->dstbus.buswidth) *
+ max_bytes_per_lli = min(bd.srcbus.buswidth, bd.dstbus.buswidth) *
PL080_CONTROL_TRANSFER_SIZE_MASK;
dev_vdbg(&pl08x->adev->dev,
- "%s max bytes per lli = %d\n",
+ "%s max bytes per lli = %zu\n",
__func__, max_bytes_per_lli);
/* We need to count this down to zero */
- remainder = txd->len;
+ bd.remainder = txd->len;
dev_vdbg(&pl08x->adev->dev,
- "%s remainder = %d\n",
- __func__, remainder);
+ "%s remainder = %zu\n",
+ __func__, bd.remainder);
/*
* Choose bus to align to
* - prefers destination bus if both available
* - if fixed address on one bus chooses other
- * - modifies cctl to choose an apropriate master
- */
- pl08x_choose_master_bus(&txd->srcbus, &txd->dstbus,
- &mbus, &sbus, cctl);
-
-
- /*
- * The lowest bit of the LLI register
- * is also used to indicate which master to
- * use for reading the LLIs.
*/
+ pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
if (txd->len < mbus->buswidth) {
- /*
- * Less than a bus width available
- * - send as single bytes
- */
- while (remainder) {
+ /* Less than a bus width available - send as single bytes */
+ while (bd.remainder) {
dev_vdbg(&pl08x->adev->dev,
"%s single byte LLIs for a transfer of "
- "less than a bus width (remain %08x)\n",
- __func__, remainder);
+ "less than a bus width (remain 0x%08x)\n",
+ __func__, bd.remainder);
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
- num_llis =
- pl08x_fill_lli_for_desc(pl08x, txd, num_llis, 1,
- cctl, &remainder);
+ pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
total_bytes++;
}
} else {
- /*
- * Make one byte LLIs until master bus is aligned
- * - slave will then be aligned also
- */
+ /* Make one byte LLIs until master bus is aligned */
while ((mbus->addr) % (mbus->buswidth)) {
dev_vdbg(&pl08x->adev->dev,
"%s adjustment lli for less than bus width "
- "(remain %08x)\n",
- __func__, remainder);
+ "(remain 0x%08x)\n",
+ __func__, bd.remainder);
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
- num_llis = pl08x_fill_lli_for_desc
- (pl08x, txd, num_llis, 1, cctl, &remainder);
+ pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
total_bytes++;
}
/*
- * Master now aligned
+ * Master now aligned
* - if slave is not then we must set its width down
*/
if (sbus->addr % sbus->buswidth) {
* Make largest possible LLIs until less than one bus
* width left
*/
- while (remainder > (mbus->buswidth - 1)) {
- int lli_len, target_len;
- int tsize;
- int odd_bytes;
+ while (bd.remainder > (mbus->buswidth - 1)) {
+ size_t lli_len, target_len, tsize, odd_bytes;
/*
* If enough left try to send max possible,
* otherwise try to send the remainder
*/
- target_len = remainder;
- if (remainder > max_bytes_per_lli)
- target_len = max_bytes_per_lli;
+ target_len = min(bd.remainder, max_bytes_per_lli);
/*
- * Set bus lengths for incrementing busses
- * to number of bytes which fill to next memory
- * boundary
+ * Set bus lengths for incrementing buses to the
+ * number of bytes which fill to next memory boundary,
+ * limiting on the target length calculated above.
*/
if (cctl & PL080_CONTROL_SRC_INCR)
- txd->srcbus.fill_bytes =
- pl08x_pre_boundary(
- txd->srcbus.addr,
- remainder);
+ bd.srcbus.fill_bytes =
+ pl08x_pre_boundary(bd.srcbus.addr,
+ target_len);
else
- txd->srcbus.fill_bytes =
- max_bytes_per_lli;
+ bd.srcbus.fill_bytes = target_len;
if (cctl & PL080_CONTROL_DST_INCR)
- txd->dstbus.fill_bytes =
- pl08x_pre_boundary(
- txd->dstbus.addr,
- remainder);
+ bd.dstbus.fill_bytes =
+ pl08x_pre_boundary(bd.dstbus.addr,
+ target_len);
else
- txd->dstbus.fill_bytes =
- max_bytes_per_lli;
+ bd.dstbus.fill_bytes = target_len;
- /*
- * Find the nearest
- */
- lli_len = min(txd->srcbus.fill_bytes,
- txd->dstbus.fill_bytes);
+ /* Find the nearest */
+ lli_len = min(bd.srcbus.fill_bytes,
+ bd.dstbus.fill_bytes);
- BUG_ON(lli_len > remainder);
+ BUG_ON(lli_len > bd.remainder);
if (lli_len <= 0) {
dev_err(&pl08x->adev->dev,
- "%s lli_len is %d, <= 0\n",
+ "%s lli_len is %zu, <= 0\n",
__func__, lli_len);
return 0;
}
if (lli_len == target_len) {
/*
- * Can send what we wanted
- */
- /*
- * Maintain alignment
+ * Can send what we wanted.
+ * Maintain alignment
*/
lli_len = (lli_len/mbus->buswidth) *
mbus->buswidth;
} else {
/*
* So now we know how many bytes to transfer
- * to get to the nearest boundary
- * The next lli will past the boundary
- * - however we may be working to a boundary
- * on the slave bus
- * We need to ensure the master stays aligned
+ * to get to the nearest boundary. The next
+ * LLI will past the boundary. However, we
+ * may be working to a boundary on the slave
+ * bus. We need to ensure the master stays
+ * aligned, and that we are working in
+ * multiples of the bus widths.
*/
odd_bytes = lli_len % mbus->buswidth;
- /*
- * - and that we are working in multiples
- * of the bus widths
- */
lli_len -= odd_bytes;
}
if (target_len != lli_len) {
dev_vdbg(&pl08x->adev->dev,
- "%s can't send what we want. Desired %08x, lli of %08x bytes in txd of %08x\n",
+ "%s can't send what we want. Desired 0x%08zx, lli of 0x%08zx bytes in txd of 0x%08zx\n",
__func__, target_len, lli_len, txd->len);
}
cctl = pl08x_cctl_bits(cctl,
- txd->srcbus.buswidth,
- txd->dstbus.buswidth,
+ bd.srcbus.buswidth,
+ bd.dstbus.buswidth,
tsize);
dev_vdbg(&pl08x->adev->dev,
- "%s fill lli with single lli chunk of size %08x (remainder %08x)\n",
- __func__, lli_len, remainder);
- num_llis = pl08x_fill_lli_for_desc(pl08x, txd,
- num_llis, lli_len, cctl,
- &remainder);
+ "%s fill lli with single lli chunk of size 0x%08zx (remainder 0x%08zx)\n",
+ __func__, lli_len, bd.remainder);
+ pl08x_fill_lli_for_desc(&bd, num_llis++,
+ lli_len, cctl);
total_bytes += lli_len;
}
if (odd_bytes) {
/*
- * Creep past the boundary,
- * maintaining master alignment
+ * Creep past the boundary, maintaining
+ * master alignment
*/
int j;
for (j = 0; (j < mbus->buswidth)
- && (remainder); j++) {
+ && (bd.remainder); j++) {
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
dev_vdbg(&pl08x->adev->dev,
- "%s align with boundardy, single byte (remain %08x)\n",
- __func__, remainder);
- num_llis =
- pl08x_fill_lli_for_desc(pl08x,
- txd, num_llis, 1,
- cctl, &remainder);
+ "%s align with boundary, single byte (remain 0x%08zx)\n",
+ __func__, bd.remainder);
+ pl08x_fill_lli_for_desc(&bd,
+ num_llis++, 1, cctl);
total_bytes++;
}
}
/*
* Send any odd bytes
*/
- if (remainder < 0) {
- dev_err(&pl08x->adev->dev, "%s remainder not fitted 0x%08x bytes\n",
- __func__, remainder);
- return 0;
- }
-
- while (remainder) {
+ while (bd.remainder) {
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
dev_vdbg(&pl08x->adev->dev,
- "%s align with boundardy, single odd byte (remain %d)\n",
- __func__, remainder);
- num_llis = pl08x_fill_lli_for_desc(pl08x, txd, num_llis,
- 1, cctl, &remainder);
+ "%s align with boundary, single odd byte (remain %zu)\n",
+ __func__, bd.remainder);
+ pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
total_bytes++;
}
}
if (total_bytes != txd->len) {
dev_err(&pl08x->adev->dev,
- "%s size of encoded lli:s don't match total txd, transferred 0x%08x from size 0x%08x\n",
+ "%s size of encoded lli:s don't match total txd, transferred 0x%08zx from size 0x%08zx\n",
__func__, total_bytes, txd->len);
return 0;
}
__func__, (u32) MAX_NUM_TSFR_LLIS);
return 0;
}
- /*
- * Decide whether this is a loop or a terminated transfer
- */
- llis_va = txd->llis_va;
- llis_bus = (struct lli *) txd->llis_bus;
-
- if (cd->circular_buffer) {
- /*
- * Loop the circular buffer so that the next element
- * points back to the beginning of the LLI.
- */
- llis_va[num_llis - 1].next =
- (dma_addr_t)((unsigned int)&(llis_bus[0]));
- } else {
- /*
- * On non-circular buffers, the final LLI terminates
- * the LLI.
- */
- llis_va[num_llis - 1].next = 0;
- /*
- * The final LLI element shall also fire an interrupt
- */
- llis_va[num_llis - 1].cctl |= PL080_CONTROL_TC_IRQ_EN;
- }
-
- /* Now store the channel register values */
- txd->csrc = llis_va[0].src;
- txd->cdst = llis_va[0].dst;
- if (num_llis > 1)
- txd->clli = llis_va[0].next;
- else
- txd->clli = 0;
- txd->cctl = llis_va[0].cctl;
- /* ccfg will be set at physical channel allocation time */
+ llis_va = txd->llis_va;
+ /* The final LLI terminates the LLI. */
+ llis_va[num_llis - 1].lli = 0;
+ /* The final LLI element shall also fire an interrupt. */
+ llis_va[num_llis - 1].cctl |= PL080_CONTROL_TC_IRQ_EN;
#ifdef VERBOSE_DEBUG
{
for (i = 0; i < num_llis; i++) {
dev_vdbg(&pl08x->adev->dev,
- "lli %d @%p: csrc=%08x, cdst=%08x, cctl=%08x, clli=%08x\n",
+ "lli %d @%p: csrc=0x%08x, cdst=0x%08x, cctl=0x%08x, clli=0x%08x\n",
i,
&llis_va[i],
llis_va[i].src,
llis_va[i].dst,
llis_va[i].cctl,
- llis_va[i].next
+ llis_va[i].lli
);
}
}
static void pl08x_free_txd(struct pl08x_driver_data *pl08x,
struct pl08x_txd *txd)
{
- if (!txd)
- dev_err(&pl08x->adev->dev,
- "%s no descriptor to free\n",
- __func__);
-
/* Free the LLI */
- dma_pool_free(pl08x->pool, txd->llis_va,
- txd->llis_bus);
+ dma_pool_free(pl08x->pool, txd->llis_va, txd->llis_bus);
pl08x->pool_ctr--;
struct pl08x_txd *txdi = NULL;
struct pl08x_txd *next;
- if (!list_empty(&plchan->desc_list)) {
+ if (!list_empty(&plchan->pend_list)) {
list_for_each_entry_safe(txdi,
- next, &plchan->desc_list, node) {
+ next, &plchan->pend_list, node) {
list_del(&txdi->node);
pl08x_free_txd(pl08x, txdi);
}
-
}
}
return -EBUSY;
}
ch->signal = ret;
+
+ /* Assign the flow control signal to this channel */
+ if (txd->direction == DMA_TO_DEVICE)
+ txd->ccfg |= ch->signal << PL080_CONFIG_DST_SEL_SHIFT;
+ else if (txd->direction == DMA_FROM_DEVICE)
+ txd->ccfg |= ch->signal << PL080_CONFIG_SRC_SEL_SHIFT;
}
dev_dbg(&pl08x->adev->dev, "allocated physical channel %d and signal %d for xfer on %s\n",
ch->signal,
plchan->name);
+ plchan->phychan_hold++;
plchan->phychan = ch;
return 0;
}
+static void release_phy_channel(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+
+ if ((plchan->phychan->signal >= 0) && pl08x->pd->put_signal) {
+ pl08x->pd->put_signal(plchan);
+ plchan->phychan->signal = -1;
+ }
+ pl08x_put_phy_channel(pl08x, plchan->phychan);
+ plchan->phychan = NULL;
+}
+
static dma_cookie_t pl08x_tx_submit(struct dma_async_tx_descriptor *tx)
{
struct pl08x_dma_chan *plchan = to_pl08x_chan(tx->chan);
+ struct pl08x_txd *txd = to_pl08x_txd(tx);
+ unsigned long flags;
+
+ spin_lock_irqsave(&plchan->lock, flags);
+
+ plchan->chan.cookie += 1;
+ if (plchan->chan.cookie < 0)
+ plchan->chan.cookie = 1;
+ tx->cookie = plchan->chan.cookie;
+
+ /* Put this onto the pending list */
+ list_add_tail(&txd->node, &plchan->pend_list);
+
+ /*
+ * If there was no physical channel available for this memcpy,
+ * stack the request up and indicate that the channel is waiting
+ * for a free physical channel.
+ */
+ if (!plchan->slave && !plchan->phychan) {
+ /* Do this memcpy whenever there is a channel ready */
+ plchan->state = PL08X_CHAN_WAITING;
+ plchan->waiting = txd;
+ } else {
+ plchan->phychan_hold--;
+ }
- atomic_inc(&plchan->last_issued);
- tx->cookie = atomic_read(&plchan->last_issued);
- /* This unlock follows the lock in the prep() function */
- spin_unlock_irqrestore(&plchan->lock, plchan->lockflags);
+ spin_unlock_irqrestore(&plchan->lock, flags);
return tx->cookie;
}
}
/*
- * Code accessing dma_async_is_complete() in a tight loop
- * may give problems - could schedule where indicated.
- * If slaves are relying on interrupts to signal completion this
- * function must not be called with interrupts disabled
+ * Code accessing dma_async_is_complete() in a tight loop may give problems.
+ * If slaves are relying on interrupts to signal completion this function
+ * must not be called with interrupts disabled.
*/
static enum dma_status
pl08x_dma_tx_status(struct dma_chan *chan,
enum dma_status ret;
u32 bytesleft = 0;
- last_used = atomic_read(&plchan->last_issued);
+ last_used = plchan->chan.cookie;
last_complete = plchan->lc;
ret = dma_async_is_complete(cookie, last_complete, last_used);
return ret;
}
- /*
- * schedule(); could be inserted here
- */
-
/*
* This cookie not complete yet
*/
- last_used = atomic_read(&plchan->last_issued);
+ last_used = plchan->chan.cookie;
last_complete = plchan->lc;
/* Get number of bytes left in the active transactions and queue */
},
};
-static void dma_set_runtime_config(struct dma_chan *chan,
- struct dma_slave_config *config)
+static int dma_set_runtime_config(struct dma_chan *chan,
+ struct dma_slave_config *config)
{
struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
struct pl08x_driver_data *pl08x = plchan->host;
struct pl08x_channel_data *cd = plchan->cd;
enum dma_slave_buswidth addr_width;
+ dma_addr_t addr;
u32 maxburst;
u32 cctl = 0;
- /* Mask out all except src and dst channel */
- u32 ccfg = cd->ccfg & 0x000003DEU;
- int i = 0;
+ int i;
+
+ if (!plchan->slave)
+ return -EINVAL;
/* Transfer direction */
plchan->runtime_direction = config->direction;
if (config->direction == DMA_TO_DEVICE) {
- plchan->runtime_addr = config->dst_addr;
- cctl |= PL080_CONTROL_SRC_INCR;
- ccfg |= PL080_FLOW_MEM2PER << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ addr = config->dst_addr;
addr_width = config->dst_addr_width;
maxburst = config->dst_maxburst;
} else if (config->direction == DMA_FROM_DEVICE) {
- plchan->runtime_addr = config->src_addr;
- cctl |= PL080_CONTROL_DST_INCR;
- ccfg |= PL080_FLOW_PER2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ addr = config->src_addr;
addr_width = config->src_addr_width;
maxburst = config->src_maxburst;
} else {
dev_err(&pl08x->adev->dev,
"bad runtime_config: alien transfer direction\n");
- return;
+ return -EINVAL;
}
switch (addr_width) {
default:
dev_err(&pl08x->adev->dev,
"bad runtime_config: alien address width\n");
- return;
+ return -EINVAL;
}
/*
* Now decide on a maxburst:
- * If this channel will only request single transfers, set
- * this down to ONE element.
+ * If this channel will only request single transfers, set this
+ * down to ONE element. Also select one element if no maxburst
+ * is specified.
*/
- if (plchan->cd->single) {
+ if (plchan->cd->single || maxburst == 0) {
cctl |= (PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT) |
(PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT);
} else {
- while (i < ARRAY_SIZE(burst_sizes)) {
+ for (i = 0; i < ARRAY_SIZE(burst_sizes); i++)
if (burst_sizes[i].burstwords <= maxburst)
break;
- i++;
- }
cctl |= burst_sizes[i].reg;
}
- /* Access the cell in privileged mode, non-bufferable, non-cacheable */
- cctl &= ~PL080_CONTROL_PROT_MASK;
- cctl |= PL080_CONTROL_PROT_SYS;
+ plchan->runtime_addr = addr;
/* Modify the default channel data to fit PrimeCell request */
cd->cctl = cctl;
- cd->ccfg = ccfg;
dev_dbg(&pl08x->adev->dev,
"configured channel %s (%s) for %s, data width %d, "
- "maxburst %d words, LE, CCTL=%08x, CCFG=%08x\n",
+ "maxburst %d words, LE, CCTL=0x%08x\n",
dma_chan_name(chan), plchan->name,
(config->direction == DMA_FROM_DEVICE) ? "RX" : "TX",
addr_width,
maxburst,
- cctl, ccfg);
+ cctl);
+
+ return 0;
}
/*
static void pl08x_issue_pending(struct dma_chan *chan)
{
struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
- struct pl08x_driver_data *pl08x = plchan->host;
unsigned long flags;
spin_lock_irqsave(&plchan->lock, flags);
- /* Something is already active */
- if (plchan->at) {
- spin_unlock_irqrestore(&plchan->lock, flags);
- return;
- }
-
- /* Didn't get a physical channel so waiting for it ... */
- if (plchan->state == PL08X_CHAN_WAITING)
+ /* Something is already active, or we're waiting for a channel... */
+ if (plchan->at || plchan->state == PL08X_CHAN_WAITING) {
+ spin_unlock_irqrestore(&plchan->lock, flags);
return;
+ }
/* Take the first element in the queue and execute it */
- if (!list_empty(&plchan->desc_list)) {
+ if (!list_empty(&plchan->pend_list)) {
struct pl08x_txd *next;
- next = list_first_entry(&plchan->desc_list,
+ next = list_first_entry(&plchan->pend_list,
struct pl08x_txd,
node);
list_del(&next->node);
- plchan->at = next;
plchan->state = PL08X_CHAN_RUNNING;
- /* Configure the physical channel for the active txd */
- pl08x_config_phychan_for_txd(plchan);
- pl08x_set_cregs(pl08x, plchan->phychan);
- pl08x_enable_phy_chan(pl08x, plchan->phychan);
+ pl08x_start_txd(plchan, next);
}
spin_unlock_irqrestore(&plchan->lock, flags);
static int pl08x_prep_channel_resources(struct pl08x_dma_chan *plchan,
struct pl08x_txd *txd)
{
- int num_llis;
struct pl08x_driver_data *pl08x = plchan->host;
- int ret;
+ unsigned long flags;
+ int num_llis, ret;
num_llis = pl08x_fill_llis_for_desc(pl08x, txd);
-
- if (!num_llis)
+ if (!num_llis) {
+ kfree(txd);
return -EINVAL;
+ }
- spin_lock_irqsave(&plchan->lock, plchan->lockflags);
-
- /*
- * If this device is not using a circular buffer then
- * queue this new descriptor for transfer.
- * The descriptor for a circular buffer continues
- * to be used until the channel is freed.
- */
- if (txd->cd->circular_buffer)
- dev_err(&pl08x->adev->dev,
- "%s attempting to queue a circular buffer\n",
- __func__);
- else
- list_add_tail(&txd->node,
- &plchan->desc_list);
+ spin_lock_irqsave(&plchan->lock, flags);
/*
* See if we already have a physical channel allocated,
ret = prep_phy_channel(plchan, txd);
if (ret) {
/*
- * No physical channel available, we will
- * stack up the memcpy channels until there is a channel
- * available to handle it whereas slave transfers may
- * have been denied due to platform channel muxing restrictions
- * and since there is no guarantee that this will ever be
- * resolved, and since the signal must be aquired AFTER
- * aquiring the physical channel, we will let them be NACK:ed
- * with -EBUSY here. The drivers can alway retry the prep()
- * call if they are eager on doing this using DMA.
+ * No physical channel was available.
+ *
+ * memcpy transfers can be sorted out at submission time.
+ *
+ * Slave transfers may have been denied due to platform
+ * channel muxing restrictions. Since there is no guarantee
+ * that this will ever be resolved, and the signal must be
+ * acquired AFTER acquiring the physical channel, we will let
+ * them be NACK:ed with -EBUSY here. The drivers can retry
+ * the prep() call if they are eager on doing this using DMA.
*/
if (plchan->slave) {
pl08x_free_txd_list(pl08x, plchan);
- spin_unlock_irqrestore(&plchan->lock, plchan->lockflags);
+ pl08x_free_txd(pl08x, txd);
+ spin_unlock_irqrestore(&plchan->lock, flags);
return -EBUSY;
}
- /* Do this memcpy whenever there is a channel ready */
- plchan->state = PL08X_CHAN_WAITING;
- plchan->waiting = txd;
} else
/*
- * Else we're all set, paused and ready to roll,
- * status will switch to PL08X_CHAN_RUNNING when
- * we call issue_pending(). If there is something
- * running on the channel already we don't change
- * its state.
+ * Else we're all set, paused and ready to roll, status
+ * will switch to PL08X_CHAN_RUNNING when we call
+ * issue_pending(). If there is something running on the
+ * channel already we don't change its state.
*/
if (plchan->state == PL08X_CHAN_IDLE)
plchan->state = PL08X_CHAN_PAUSED;
- /*
- * Notice that we leave plchan->lock locked on purpose:
- * it will be unlocked in the subsequent tx_submit()
- * call. This is a consequence of the current API.
- */
+ spin_unlock_irqrestore(&plchan->lock, flags);
return 0;
}
+/*
+ * Given the source and destination available bus masks, select which
+ * will be routed to each port. We try to have source and destination
+ * on separate ports, but always respect the allowable settings.
+ */
+static u32 pl08x_select_bus(struct pl08x_driver_data *pl08x, u8 src, u8 dst)
+{
+ u32 cctl = 0;
+
+ if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
+ cctl |= PL080_CONTROL_DST_AHB2;
+ if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
+ cctl |= PL080_CONTROL_SRC_AHB2;
+
+ return cctl;
+}
+
+static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan,
+ unsigned long flags)
+{
+ struct pl08x_txd *txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+
+ if (txd) {
+ dma_async_tx_descriptor_init(&txd->tx, &plchan->chan);
+ txd->tx.flags = flags;
+ txd->tx.tx_submit = pl08x_tx_submit;
+ INIT_LIST_HEAD(&txd->node);
+
+ /* Always enable error and terminal interrupts */
+ txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK;
+ }
+ return txd;
+}
+
/*
* Initialize a descriptor to be used by memcpy submit
*/
struct pl08x_txd *txd;
int ret;
- txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+ txd = pl08x_get_txd(plchan, flags);
if (!txd) {
dev_err(&pl08x->adev->dev,
"%s no memory for descriptor\n", __func__);
return NULL;
}
- dma_async_tx_descriptor_init(&txd->tx, chan);
txd->direction = DMA_NONE;
- txd->srcbus.addr = src;
- txd->dstbus.addr = dest;
+ txd->src_addr = src;
+ txd->dst_addr = dest;
+ txd->len = len;
/* Set platform data for m2m */
- txd->cd = &pl08x->pd->memcpy_channel;
+ txd->ccfg |= PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ txd->cctl = pl08x->pd->memcpy_channel.cctl &
+ ~(PL080_CONTROL_DST_AHB2 | PL080_CONTROL_SRC_AHB2);
+
/* Both to be incremented or the code will break */
- txd->cd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
- txd->tx.tx_submit = pl08x_tx_submit;
- txd->tx.callback = NULL;
- txd->tx.callback_param = NULL;
- txd->len = len;
+ txd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
+
+ if (pl08x->vd->dualmaster)
+ txd->cctl |= pl08x_select_bus(pl08x,
+ pl08x->mem_buses, pl08x->mem_buses);
- INIT_LIST_HEAD(&txd->node);
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
return NULL;
- /*
- * NB: the channel lock is held at this point so tx_submit()
- * must be called in direct succession.
- */
return &txd->tx;
}
-struct dma_async_tx_descriptor *pl08x_prep_slave_sg(
+static struct dma_async_tx_descriptor *pl08x_prep_slave_sg(
struct dma_chan *chan, struct scatterlist *sgl,
unsigned int sg_len, enum dma_data_direction direction,
unsigned long flags)
struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
struct pl08x_driver_data *pl08x = plchan->host;
struct pl08x_txd *txd;
+ u8 src_buses, dst_buses;
int ret;
/*
dev_dbg(&pl08x->adev->dev, "%s prepare transaction of %d bytes from %s\n",
__func__, sgl->length, plchan->name);
- txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+ txd = pl08x_get_txd(plchan, flags);
if (!txd) {
dev_err(&pl08x->adev->dev, "%s no txd\n", __func__);
return NULL;
}
- dma_async_tx_descriptor_init(&txd->tx, chan);
-
if (direction != plchan->runtime_direction)
dev_err(&pl08x->adev->dev, "%s DMA setup does not match "
"the direction configured for the PrimeCell\n",
* channel target address dynamically at runtime.
*/
txd->direction = direction;
+ txd->len = sgl->length;
+
+ txd->cctl = plchan->cd->cctl &
+ ~(PL080_CONTROL_SRC_AHB2 | PL080_CONTROL_DST_AHB2 |
+ PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR |
+ PL080_CONTROL_PROT_MASK);
+
+ /* Access the cell in privileged mode, non-bufferable, non-cacheable */
+ txd->cctl |= PL080_CONTROL_PROT_SYS;
+
if (direction == DMA_TO_DEVICE) {
- txd->srcbus.addr = sgl->dma_address;
+ txd->ccfg |= PL080_FLOW_MEM2PER << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ txd->cctl |= PL080_CONTROL_SRC_INCR;
+ txd->src_addr = sgl->dma_address;
if (plchan->runtime_addr)
- txd->dstbus.addr = plchan->runtime_addr;
+ txd->dst_addr = plchan->runtime_addr;
else
- txd->dstbus.addr = plchan->cd->addr;
+ txd->dst_addr = plchan->cd->addr;
+ src_buses = pl08x->mem_buses;
+ dst_buses = plchan->cd->periph_buses;
} else if (direction == DMA_FROM_DEVICE) {
+ txd->ccfg |= PL080_FLOW_PER2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ txd->cctl |= PL080_CONTROL_DST_INCR;
if (plchan->runtime_addr)
- txd->srcbus.addr = plchan->runtime_addr;
+ txd->src_addr = plchan->runtime_addr;
else
- txd->srcbus.addr = plchan->cd->addr;
- txd->dstbus.addr = sgl->dma_address;
+ txd->src_addr = plchan->cd->addr;
+ txd->dst_addr = sgl->dma_address;
+ src_buses = plchan->cd->periph_buses;
+ dst_buses = pl08x->mem_buses;
} else {
dev_err(&pl08x->adev->dev,
"%s direction unsupported\n", __func__);
return NULL;
}
- txd->cd = plchan->cd;
- txd->tx.tx_submit = pl08x_tx_submit;
- txd->tx.callback = NULL;
- txd->tx.callback_param = NULL;
- txd->len = sgl->length;
- INIT_LIST_HEAD(&txd->node);
+
+ txd->cctl |= pl08x_select_bus(pl08x, src_buses, dst_buses);
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
return NULL;
- /*
- * NB: the channel lock is held at this point so tx_submit()
- * must be called in direct succession.
- */
return &txd->tx;
}
/* Controls applicable to inactive channels */
if (cmd == DMA_SLAVE_CONFIG) {
- dma_set_runtime_config(chan,
- (struct dma_slave_config *)
- arg);
- return 0;
+ return dma_set_runtime_config(chan,
+ (struct dma_slave_config *)arg);
}
/*
plchan->state = PL08X_CHAN_IDLE;
if (plchan->phychan) {
- pl08x_stop_phy_chan(plchan->phychan);
+ pl08x_terminate_phy_chan(pl08x, plchan->phychan);
/*
* Mark physical channel as free and free any slave
* signal
*/
- if ((plchan->phychan->signal >= 0) &&
- pl08x->pd->put_signal) {
- pl08x->pd->put_signal(plchan);
- plchan->phychan->signal = -1;
- }
- pl08x_put_phy_channel(pl08x, plchan->phychan);
- plchan->phychan = NULL;
+ release_phy_channel(plchan);
}
- /* Stop any pending tasklet */
- tasklet_disable(&plchan->tasklet);
/* Dequeue jobs and free LLIs */
if (plchan->at) {
pl08x_free_txd(pl08x, plchan->at);
/*
* Just check that the device is there and active
- * TODO: turn this bit on/off depending on the number of
- * physical channels actually used, if it is zero... well
- * shut it off. That will save some power. Cut the clock
- * at the same time.
+ * TODO: turn this bit on/off depending on the number of physical channels
+ * actually used, if it is zero... well shut it off. That will save some
+ * power. Cut the clock at the same time.
*/
static void pl08x_ensure_on(struct pl08x_driver_data *pl08x)
{
val = readl(pl08x->base + PL080_CONFIG);
val &= ~(PL080_CONFIG_M2_BE | PL080_CONFIG_M1_BE | PL080_CONFIG_ENABLE);
- /* We implictly clear bit 1 and that means little-endian mode */
+ /* We implicitly clear bit 1 and that means little-endian mode */
val |= PL080_CONFIG_ENABLE;
writel(val, pl08x->base + PL080_CONFIG);
}
+static void pl08x_unmap_buffers(struct pl08x_txd *txd)
+{
+ struct device *dev = txd->tx.chan->device->dev;
+
+ if (!(txd->tx.flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ if (txd->tx.flags & DMA_COMPL_SRC_UNMAP_SINGLE)
+ dma_unmap_single(dev, txd->src_addr, txd->len,
+ DMA_TO_DEVICE);
+ else
+ dma_unmap_page(dev, txd->src_addr, txd->len,
+ DMA_TO_DEVICE);
+ }
+ if (!(txd->tx.flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ if (txd->tx.flags & DMA_COMPL_DEST_UNMAP_SINGLE)
+ dma_unmap_single(dev, txd->dst_addr, txd->len,
+ DMA_FROM_DEVICE);
+ else
+ dma_unmap_page(dev, txd->dst_addr, txd->len,
+ DMA_FROM_DEVICE);
+ }
+}
+
static void pl08x_tasklet(unsigned long data)
{
struct pl08x_dma_chan *plchan = (struct pl08x_dma_chan *) data;
- struct pl08x_phy_chan *phychan = plchan->phychan;
struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_txd *txd;
+ unsigned long flags;
- if (!plchan)
- BUG();
-
- spin_lock(&plchan->lock);
-
- if (plchan->at) {
- dma_async_tx_callback callback =
- plchan->at->tx.callback;
- void *callback_param =
- plchan->at->tx.callback_param;
-
- /*
- * Update last completed
- */
- plchan->lc =
- (plchan->at->tx.cookie);
-
- /*
- * Callback to signal completion
- */
- if (callback)
- callback(callback_param);
+ spin_lock_irqsave(&plchan->lock, flags);
- /*
- * Device callbacks should NOT clear
- * the current transaction on the channel
- * Linus: sometimes they should?
- */
- if (!plchan->at)
- BUG();
+ txd = plchan->at;
+ plchan->at = NULL;
- /*
- * Free the descriptor if it's not for a device
- * using a circular buffer
- */
- if (!plchan->at->cd->circular_buffer) {
- pl08x_free_txd(pl08x, plchan->at);
- plchan->at = NULL;
- }
- /*
- * else descriptor for circular
- * buffers only freed when
- * client has disabled dma
- */
+ if (txd) {
+ /* Update last completed */
+ plchan->lc = txd->tx.cookie;
}
- /*
- * If a new descriptor is queued, set it up
- * plchan->at is NULL here
- */
- if (!list_empty(&plchan->desc_list)) {
+
+ /* If a new descriptor is queued, set it up plchan->at is NULL here */
+ if (!list_empty(&plchan->pend_list)) {
struct pl08x_txd *next;
- next = list_first_entry(&plchan->desc_list,
+ next = list_first_entry(&plchan->pend_list,
struct pl08x_txd,
node);
list_del(&next->node);
- plchan->at = next;
- /* Configure the physical channel for the next txd */
- pl08x_config_phychan_for_txd(plchan);
- pl08x_set_cregs(pl08x, plchan->phychan);
- pl08x_enable_phy_chan(pl08x, plchan->phychan);
+
+ pl08x_start_txd(plchan, next);
+ } else if (plchan->phychan_hold) {
+ /*
+ * This channel is still in use - we have a new txd being
+ * prepared and will soon be queued. Don't give up the
+ * physical channel.
+ */
} else {
struct pl08x_dma_chan *waiting = NULL;
* No more jobs, so free up the physical channel
* Free any allocated signal on slave transfers too
*/
- if ((phychan->signal >= 0) && pl08x->pd->put_signal) {
- pl08x->pd->put_signal(plchan);
- phychan->signal = -1;
- }
- pl08x_put_phy_channel(pl08x, phychan);
- plchan->phychan = NULL;
+ release_phy_channel(plchan);
plchan->state = PL08X_CHAN_IDLE;
/*
- * And NOW before anyone else can grab that free:d
- * up physical channel, see if there is some memcpy
- * pending that seriously needs to start because of
- * being stacked up while we were choking the
- * physical channels with data.
+ * And NOW before anyone else can grab that free:d up
+ * physical channel, see if there is some memcpy pending
+ * that seriously needs to start because of being stacked
+ * up while we were choking the physical channels with data.
*/
list_for_each_entry(waiting, &pl08x->memcpy.channels,
chan.device_node) {
ret = prep_phy_channel(waiting,
waiting->waiting);
BUG_ON(ret);
+ waiting->phychan_hold--;
waiting->state = PL08X_CHAN_RUNNING;
waiting->waiting = NULL;
pl08x_issue_pending(&waiting->chan);
}
}
- spin_unlock(&plchan->lock);
+ spin_unlock_irqrestore(&plchan->lock, flags);
+
+ if (txd) {
+ dma_async_tx_callback callback = txd->tx.callback;
+ void *callback_param = txd->tx.callback_param;
+
+ /* Don't try to unmap buffers on slave channels */
+ if (!plchan->slave)
+ pl08x_unmap_buffers(txd);
+
+ /* Free the descriptor */
+ spin_lock_irqsave(&plchan->lock, flags);
+ pl08x_free_txd(pl08x, txd);
+ spin_unlock_irqrestore(&plchan->lock, flags);
+
+ /* Callback to signal completion */
+ if (callback)
+ callback(callback_param);
+ }
}
static irqreturn_t pl08x_irq(int irq, void *dev)
val = readl(pl08x->base + PL080_ERR_STATUS);
if (val) {
- /*
- * An error interrupt (on one or more channels)
- */
+ /* An error interrupt (on one or more channels) */
dev_err(&pl08x->adev->dev,
"%s error interrupt, register value 0x%08x\n",
__func__, val);
mask |= (1 << i);
}
}
- /*
- * Clear only the terminal interrupts on channels we processed
- */
+ /* Clear only the terminal interrupts on channels we processed */
writel(mask, pl08x->base + PL080_TC_CLEAR);
return mask ? IRQ_HANDLED : IRQ_NONE;
int i;
INIT_LIST_HEAD(&dmadev->channels);
+
/*
* Register as many many memcpy as we have physical channels,
* we won't always be able to use all but the code will have
return -ENOMEM;
}
}
+ if (chan->cd->circular_buffer) {
+ dev_err(&pl08x->adev->dev,
+ "channel %s: circular buffers not supported\n",
+ chan->name);
+ kfree(chan);
+ continue;
+ }
dev_info(&pl08x->adev->dev,
"initialize virtual channel \"%s\"\n",
chan->name);
chan->chan.device = dmadev;
- atomic_set(&chan->last_issued, 0);
- chan->lc = atomic_read(&chan->last_issued);
+ chan->chan.cookie = 0;
+ chan->lc = 0;
spin_lock_init(&chan->lock);
- INIT_LIST_HEAD(&chan->desc_list);
+ INIT_LIST_HEAD(&chan->pend_list);
tasklet_init(&chan->tasklet, pl08x_tasklet,
(unsigned long) chan);
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->memcpy.channels, chan.device_node) {
- seq_printf(s, "%s\t\t\%s\n", chan->name,
+ seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
}
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->slave.channels, chan.device_node) {
- seq_printf(s, "%s\t\t\%s\n", chan->name,
+ seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
}
static int pl08x_probe(struct amba_device *adev, struct amba_id *id)
{
struct pl08x_driver_data *pl08x;
- struct vendor_data *vd = id->data;
+ const struct vendor_data *vd = id->data;
int ret = 0;
int i;
pl08x->adev = adev;
pl08x->vd = vd;
+ /* By default, AHB1 only. If dualmaster, from platform */
+ pl08x->lli_buses = PL08X_AHB1;
+ pl08x->mem_buses = PL08X_AHB1;
+ if (pl08x->vd->dualmaster) {
+ pl08x->lli_buses = pl08x->pd->lli_buses;
+ pl08x->mem_buses = pl08x->pd->mem_buses;
+ }
+
/* A DMA memory pool for LLIs, align on 1-byte boundary */
pl08x->pool = dma_pool_create(DRIVER_NAME, &pl08x->adev->dev,
PL08X_LLI_TSFR_SIZE, PL08X_ALIGN, 0);
/* Turn on the PL08x */
pl08x_ensure_on(pl08x);
- /*
- * Attach the interrupt handler
- */
+ /* Attach the interrupt handler */
writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
writel(0x000000FF, pl08x->base + PL080_TC_CLEAR);
ret = request_irq(adev->irq[0], pl08x_irq, IRQF_DISABLED,
- vd->name, pl08x);
+ DRIVER_NAME, pl08x);
if (ret) {
dev_err(&adev->dev, "%s failed to request interrupt %d\n",
__func__, adev->irq[0]);
amba_set_drvdata(adev, pl08x);
init_pl08x_debugfs(pl08x);
- dev_info(&pl08x->adev->dev, "ARM(R) %s DMA block initialized @%08x\n",
- vd->name, adev->res.start);
+ dev_info(&pl08x->adev->dev, "DMA: PL%03x rev%u at 0x%08llx irq %d\n",
+ amba_part(adev), amba_rev(adev),
+ (unsigned long long)adev->res.start, adev->irq[0]);
return 0;
out_no_slave_reg:
/* PL080 has 8 channels and the PL080 have just 2 */
static struct vendor_data vendor_pl080 = {
- .name = "PL080",
.channels = 8,
.dualmaster = true,
};
static struct vendor_data vendor_pl081 = {
- .name = "PL081",
.channels = 2,
.dualmaster = false,
};
retval = amba_driver_register(&pl08x_amba_driver);
if (retval)
printk(KERN_WARNING DRIVER_NAME
- "failed to register as an amba device (%d)\n",
+ "failed to register as an AMBA device (%d)\n",
retval);
return retval;
}
projects / mv-sheeva.git / blobdiff