#define _LINUX_ETHTOOL_H
#include <linux/types.h>
+#include <linux/if_ether.h>
/* This should work for both 32 and 64 bit userland. */
struct ethtool_cmd {
* flag differs from the read-only value.
*/
enum ethtool_flags {
+ ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */
+ ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */
ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */
ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */
ETH_FLAG_RXHASH = (1 << 28),
};
/* The following structures are for supporting RX network flow
- * classification configuration. Note, all multibyte fields, e.g.,
- * ip4src, ip4dst, psrc, pdst, spi, etc. are expected to be in network
- * byte order.
+ * classification and RX n-tuple configuration. Note, all multibyte
+ * fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to
+ * be in network byte order.
+ */
+
+/**
+ * struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc.
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tos: Type-of-service
+ *
+ * This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow.
*/
struct ethtool_tcpip4_spec {
__be32 ip4src;
__u8 tos;
};
+/**
+ * struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @spi: Security parameters index
+ * @tos: Type-of-service
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv4.
+ */
struct ethtool_ah_espip4_spec {
__be32 ip4src;
__be32 ip4dst;
__u8 tos;
};
-struct ethtool_rawip4_spec {
- __be32 ip4src;
- __be32 ip4dst;
- __u8 hdata[64];
-};
-
-struct ethtool_ether_spec {
- __be16 ether_type;
- __u8 frame_size;
- __u8 eframe[16];
-};
-
#define ETH_RX_NFC_IP4 1
-#define ETH_RX_NFC_IP6 2
+/**
+ * struct ethtool_usrip4_spec - general flow specification for IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tos: Type-of-service
+ * @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0
+ * @proto: Transport protocol number; mask must be 0
+ */
struct ethtool_usrip4_spec {
__be32 ip4src;
__be32 ip4dst;
__u8 proto;
};
+/**
+ * struct ethtool_rx_flow_spec - specification for RX flow filter
+ * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
+ * @h_u: Flow fields to match (dependent on @flow_type)
+ * @m_u: Masks for flow field bits to be ignored
+ * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC
+ * if packets should be discarded
+ * @location: Index of filter in hardware table
+ */
struct ethtool_rx_flow_spec {
__u32 flow_type;
union {
struct ethtool_tcpip4_spec sctp_ip4_spec;
struct ethtool_ah_espip4_spec ah_ip4_spec;
struct ethtool_ah_espip4_spec esp_ip4_spec;
- struct ethtool_rawip4_spec raw_ip4_spec;
- struct ethtool_ether_spec ether_spec;
struct ethtool_usrip4_spec usr_ip4_spec;
- __u8 hdata[64];
- } h_u, m_u; /* entry, mask */
+ struct ethhdr ether_spec;
+ __u8 hdata[72];
+ } h_u, m_u;
__u64 ring_cookie;
__u32 location;
};
+/**
+ * struct ethtool_rxnfc - command to get or set RX flow classification rules
+ * @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH,
+ * %ETHTOOL_GRXRINGS, %ETHTOOL_GRXCLSRLCNT, %ETHTOOL_GRXCLSRULE,
+ * %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS
+ * @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW
+ * @data: Command-dependent value
+ * @fs: Flow filter specification
+ * @rule_cnt: Number of rules to be affected
+ * @rule_locs: Array of valid rule indices
+ *
+ * For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating
+ * the fields included in the flow hash, e.g. %RXH_IP_SRC. The following
+ * structure fields must not be used.
+ *
+ * For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues
+ * on return.
+ *
+ * For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined
+ * rules on return.
+ *
+ * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the index of an
+ * existing filter rule on entry and @fs contains the rule on return.
+ *
+ * For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the
+ * user buffer for @rule_locs on entry. On return, @data is the size
+ * of the filter table and @rule_locs contains the indices of the
+ * defined rules.
+ *
+ * For %ETHTOOL_SRXCLSRLINS, @fs specifies the filter rule to add or
+ * update. @fs.@location specifies the index to use and must not be
+ * ignored.
+ *
+ * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the index of an
+ * existing filter rule on entry.
+ *
+ * Implementation of indexed classification rules generally requires a
+ * TCAM.
+ */
struct ethtool_rxnfc {
__u32 cmd;
__u32 flow_type;
- /* The rx flow hash value or the rule DB size */
__u64 data;
- /* The following fields are not valid and must not be used for
- * the ETHTOOL_{G,X}RXFH commands. */
struct ethtool_rx_flow_spec fs;
__u32 rule_cnt;
__u32 rule_locs[0];
};
+/**
+ * struct ethtool_rxfh_indir - command to get or set RX flow hash indirection
+ * @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR
+ * @size: On entry, the array size of the user buffer. On return from
+ * %ETHTOOL_GRXFHINDIR, the array size of the hardware indirection table.
+ * @ring_index: RX ring/queue index for each hash value
+ */
struct ethtool_rxfh_indir {
__u32 cmd;
- /* On entry, this is the array size of the user buffer. On
- * return from ETHTOOL_GRXFHINDIR, this is the array size of
- * the hardware indirection table. */
__u32 size;
- __u32 ring_index[0]; /* ring/queue index for each hash value */
+ __u32 ring_index[0];
};
+/**
+ * struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter
+ * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
+ * @h_u: Flow field values to match (dependent on @flow_type)
+ * @m_u: Masks for flow field value bits to be ignored
+ * @vlan_tag: VLAN tag to match
+ * @vlan_tag_mask: Mask for VLAN tag bits to be ignored
+ * @data: Driver-dependent data to match
+ * @data_mask: Mask for driver-dependent data bits to be ignored
+ * @action: RX ring/queue index to deliver to (non-negative) or other action
+ * (negative, e.g. %ETHTOOL_RXNTUPLE_ACTION_DROP)
+ *
+ * For flow types %TCP_V4_FLOW, %UDP_V4_FLOW and %SCTP_V4_FLOW, where
+ * a field value and mask are both zero this is treated as if all mask
+ * bits are set i.e. the field is ignored.
+ */
struct ethtool_rx_ntuple_flow_spec {
__u32 flow_type;
union {
struct ethtool_tcpip4_spec sctp_ip4_spec;
struct ethtool_ah_espip4_spec ah_ip4_spec;
struct ethtool_ah_espip4_spec esp_ip4_spec;
- struct ethtool_rawip4_spec raw_ip4_spec;
- struct ethtool_ether_spec ether_spec;
struct ethtool_usrip4_spec usr_ip4_spec;
- __u8 hdata[64];
- } h_u, m_u; /* entry, mask */
+ struct ethhdr ether_spec;
+ __u8 hdata[72];
+ } h_u, m_u;
__u16 vlan_tag;
__u16 vlan_tag_mask;
- __u64 data; /* user-defined flow spec data */
- __u64 data_mask; /* user-defined flow spec mask */
+ __u64 data;
+ __u64 data_mask;
- /* signed to distinguish between queue and actions (DROP) */
__s32 action;
-#define ETHTOOL_RXNTUPLE_ACTION_DROP -1
+#define ETHTOOL_RXNTUPLE_ACTION_DROP (-1) /* drop packet */
+#define ETHTOOL_RXNTUPLE_ACTION_CLEAR (-2) /* clear filter */
};
+/**
+ * struct ethtool_rx_ntuple - command to set or clear RX flow filter
+ * @cmd: Command number - %ETHTOOL_SRXNTUPLE
+ * @fs: Flow filter specification
+ */
struct ethtool_rx_ntuple {
__u32 cmd;
struct ethtool_rx_ntuple_flow_spec fs;
#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */
#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */
#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */
-#define ETHTOOL_GLINK 0x0000000a /* Get link status (ethtool_value) */
+/* Get link status for host, i.e. whether the interface *and* the
+ * physical port (if there is one) are up (ethtool_value). */
+#define ETHTOOL_GLINK 0x0000000a
#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */
#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */
#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */
#define WAKE_MAGIC (1 << 5)
#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */
-/* L3-L4 network traffic flow types */
-#define TCP_V4_FLOW 0x01
-#define UDP_V4_FLOW 0x02
-#define SCTP_V4_FLOW 0x03
-#define AH_ESP_V4_FLOW 0x04
-#define TCP_V6_FLOW 0x05
-#define UDP_V6_FLOW 0x06
-#define SCTP_V6_FLOW 0x07
-#define AH_ESP_V6_FLOW 0x08
-#define AH_V4_FLOW 0x09
-#define ESP_V4_FLOW 0x0a
-#define AH_V6_FLOW 0x0b
-#define ESP_V6_FLOW 0x0c
-#define IP_USER_FLOW 0x0d
-#define IPV4_FLOW 0x10
-#define IPV6_FLOW 0x11
+/* L2-L4 network traffic flow types */
+#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */
+#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
+#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
+#define AH_ESP_V4_FLOW 0x04 /* hash only */
+#define TCP_V6_FLOW 0x05 /* hash only */
+#define UDP_V6_FLOW 0x06 /* hash only */
+#define SCTP_V6_FLOW 0x07 /* hash only */
+#define AH_ESP_V6_FLOW 0x08 /* hash only */
+#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
+#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
+#define AH_V6_FLOW 0x0b /* hash only */
+#define ESP_V6_FLOW 0x0c /* hash only */
+#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define IPV4_FLOW 0x10 /* hash only */
+#define IPV6_FLOW 0x11 /* hash only */
+#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
/* L3-L4 network traffic flow hash options */
#define RXH_L2DA (1 << 1)
projects / mv-sheeva.git / blobdiff