Larry Finger [Mon, 30 Jan 2012 15:54:49 +0000 (09:54 -0600)]
rtlwifi: Convert to asynchronous firmware load
This patch addresses a kernel bugzilla report and two recent mail threads.
The kernel bugzilla report is https://bugzilla.kernel.org/show_bug.cgi?id=42632,
which reports a udev timeout on boot.
The first mail thread, which was on LKML (http://lkml.indiana.edu/hypermail/
linux/kernel/1112.3/00965.html) was for a WARNING that occurs after a
suspend/resume cycle for rtl8192cu.
The scond mail thread (http://marc.info/?l=linux-wireless&m=132655490826766&w=2)
concerned changes in udev that break drivers that delay while firmware is loaded
on modprobe.
This patch converts all rtlwifi-based drivers to use the asynchronous firmware
loading mechanism. Drivers rtl8192ce, rtl8192cu and rtl8192de share a common
callback routine. Driver rtl8192se needs different handling of the firmware,
thus it has its own code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 28 Jan 2012 16:30:52 +0000 (08:30 -0800)]
iwlwifi: always restrict scan dwell in P2P
Whenever the PAN (P2P) context is active, it
has timers in the uCode that prevent sleep,
so scanning can't be out of channel for more
than the beacon interval programmed into the
device.
Before this patch, a full scan including any
passive channels when P2P was active would
stall forever because it wouldn't find time
to execute the passive requests (for default
beacon intervals of 100 TU.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 28 Jan 2012 16:30:50 +0000 (08:30 -0800)]
iwlwifi: fix uCode event tracing
Fix multiple bugs in event tracing:
1) If you enable uCode tracing with the device down,
it will still attempt to access the device and
continuously log "MAC is in deep sleep!" errors.
Fix this by only starting logging when the device
is actually alive.
2) Now you can set the flag when the device is down,
but logging doesn't happen when you bring it up.
To fix that, start logging when the device comes
alive. This means we don't log before -- we could
do that but I don't need it right now.
3) For some reason we read the error instead of the
event log -- use the right pointer.
4) Optimise SRAM reading of event log header.
5) Fix reading write pointer == capacity, which can
happen due to racy SRAM access
6) Most importantly: fix an error where we would try
to read WAY too many events (like 2^32-300) when
we read the wrap counter before it is updated by
the uCode -- this does happen in practice and will
cause the driver to hang the machine.
7) Finally, change the timer to 10ms instead of 100ms
as 100ms is too slow to capture all data with a
normal event log and with 100ms the log will wrap
multiple times before we have a chance to read it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 27 Jan 2012 10:02:53 +0000 (11:02 +0100)]
mac80211: Move num_sta_ps counter decrement after synchronize_rcu
Unted the assumption that the sta struct is still accessible before the
synchronize_rcu call we should move the num_sta_ps counter decrement
after synchronize_rcu to avoid incorrect decrements if num_sta_ps.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Sat, 28 Jan 2012 16:25:33 +0000 (17:25 +0100)]
mac80211: add support for mcs masks
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Sat, 28 Jan 2012 16:25:32 +0000 (17:25 +0100)]
nl80211: add support for mcs masks
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 27 Jan 2012 19:59:25 +0000 (13:59 -0600)]
rtlwifi: Move pr_fmt macros to a single location
Although the rtlwifi family of devices contains 11 copies of the pr_fmt
macro, the macro is not defined for all routines that need it. By moving
the macro to wifi.h, a single copy is available for all routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 30 Jan 2012 14:18:00 +0000 (15:18 +0100)]
mac80211: Fix incorrect num_sta_ps decrement in ap_sta_ps_end
If the driver blocked this specific STA with the help of
ieee80211_sta_block_awake we won't clear WLAN_STA_PS_STA later but
still decrement num_sta_ps. Hence, the next data frame from this
STA will trigger ap_sta_ps_end again and also decrement num_sta_ps
again leading to an incorrect num_sta_ps counter.
This can result in problems with powersaving clients not waking up
from PS because the TIM calculation might be skipped due to the
incorrect num_sta_ps counter.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 27 Jan 2012 10:02:51 +0000 (11:02 +0100)]
mac80211: Fix incorrect num_sta_ps decrement in __sta_info_destroy
When WLAN_STA_PS_DRIVER is set by ieee80211_sta_block_awake the
num_sta_ps counter is not incremented. Hence, we shouldn't decrement
it in __sta_info_destroy if only WLAN_STA_PS_DRIVER is set. This
could result in an incorrect num_sta_ps counter leading to strange side
effects with associated powersaving clients.
Fix this by only decrementing num_sta_ps when WLAN_STA_PS_STA was set
before.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 12 Jan 2012 08:31:10 +0000 (09:31 +0100)]
mac80211: station state transition error handling
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Configuring correct MAC address in broadcast key
While configuring the broadcast key in the hardware, in
multi-BSS environment, BSSes other than first were
incorrectly configured with the MAC address of first
BSS. Fixing it with correct MAC addresses.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Do not scan for IBSS merge with a fixed BSSID.
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90602d4557ee05db2a157a4e0,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Thu, 26 Jan 2012 11:36:05 +0000 (13:36 +0200)]
mac80211: send null packet on active (psm) reconfiguration
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Thu, 26 Jan 2012 06:13:31 +0000 (09:13 +0300)]
nfc: NULL vs zero in nci_activate_target()
This is a pointer so it should be NULL instead of zero. Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Wed, 25 Jan 2012 04:50:25 +0000 (20:50 -0800)]
mwifiex: update BSS parameters in dump_station_info()
This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 25 Jan 2012 04:50:24 +0000 (20:50 -0800)]
mwifiex: pass priv pointer instead of adapter
Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800: zero MAC_SYS_CTRL bits during BBP and MAC reset
Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Sat, 21 Jan 2012 19:03:00 +0000 (11:03 -0800)]
kernel-doc: fix new warnings in cfg80211.h
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.
Requested-by: Harshal Chhaya <harshal@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Fri, 20 Jan 2012 17:02:16 +0000 (01:02 +0800)]
{nl,cfg,mac}80211: Add support of setting non-forwarding entity in Mesh
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 19 Jan 2012 08:29:58 +0000 (09:29 +0100)]
mac80211: make CQM RSSI support per virtual interface
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 19 Jan 2012 08:29:57 +0000 (09:29 +0100)]
mac80211: make beacon filtering per virtual interface
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 24 Jan 2012 19:58:47 +0000 (14:58 -0500)]
ath5k: use bool type for no_hw_rfkill_switch module parameter
Avoids this:
CC [M] drivers/net/wireless/ath/ath5k/base.o
drivers/net/wireless/ath/ath5k/base.c: In function ‘__check_no_hw_rfkill_switch’:
drivers/net/wireless/ath/ath5k/base.c:85:1: warning: return from incompatible pointer type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Wed, 18 Jan 2012 11:16:14 +0000 (13:16 +0200)]
NFC: Add NCI multiple targets support
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Wed, 18 Jan 2012 11:16:13 +0000 (13:16 +0200)]
NFC: NFC core layer should not set the target_idx
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: in IBSS use the Auth frame to trigger STA reinsertion
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: add a 2-way Authentication challenge to IBSS mode
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 12:11:32 +0000 (14:11 +0200)]
NFC: Download TI NFC init script
Download TI NFC init script during nfcwilink open operation,
after the NFC channel is registered with TI shared transport.
TI NFC init script is written in BTS format.
First, read the chip version via a special vendor specific command.
Second, we request the relevant BTS file from the user space, and
then send the BTS commands to the chip.
Signed-off-by: Ilan Elias <ilane@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 09:06:43 +0000 (11:06 +0200)]
NFC: Export new attributes sensb_res and sensf_res
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:42 +0000 (00:38 -0800)]
brcm80211: Convert printk(KERN_DEBUG to pr_debug
Use pr_debug to allow dynamic debugging to work.
Move an #endif to allow brcmf_dbg_hex_dump
to be outside the #if/#endif block.
Move a const char* declaration to be inside a
pr_debug so the function doesn't need a #if/#endif
block.
Don't use temporaries in debugging functions so
the code can be optimized away.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the early days, this was a quite useful software
feature for testing different regdomains and chain
configurations without adding debugfs cruft into
the driver. Nowadays, the driver's phy code seems
to be stable and there's no need for it anymore.
Therefore I decided to removed altogether.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: derive priv from net_device instead of wiphy
Currently mwifiex_private pointers are derived from wiphy
structures. This will always work as long as there is only
one net_device associated with one wiphy. In scenarios where
there are multiple net_devices associated with single
wiphy, one should use net_device to derive the priv.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: use bss_type and bss_num to retrieve priv
Current implementation, for retrieving priv from adapter,
uses bss_index. In multi interface environment supporting
different types, bss_index may not be unique.
Use bss_type along with bss_num to retrieve the priv.
bss_index is removed with this change.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hong Wu [Wed, 11 Jan 2012 18:34:30 +0000 (20:34 +0200)]
mac80211: Fix the maximum transmit power with power constraint
The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)
Signed-off-by: Hong Wu <hong.wu@dspg.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hong Wu [Wed, 11 Jan 2012 18:33:39 +0000 (20:33 +0200)]
wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit power
The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
On carl9170, HW encryption is disabled on IBSS; the mac80211
software-based encryption is used instead. As mac80211 supports IBSS
RSN (per-STA GTK), claim its support in the carl9170 PHY.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 9 Jan 2012 12:57:36 +0000 (13:57 +0100)]
mac80211: refactor __ieee80211_get_channel_mode
Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Sun, 8 Jan 2012 09:21:53 +0000 (11:21 +0200)]
NFC: Complete NCI deactivate in deactivate_ntf
If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).
Signed-off-by: Ilan Elias <ilane@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:41 +0000 (20:46 -0600)]
rtl8192cu: Remove dead code never selected
The original driver contained some conditional code that was not selected,
but was not deleted in case it would be used later. That code can now be
removed.
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:40 +0000 (20:46 -0600)]
rtlwifi: rtl8192c_common: rtl8192de: Check for allocation failures
In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:31 +0000 (13:16 -0800)]
iwlwifi: update error dump in testmode command sram_read
The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:30 +0000 (13:16 -0800)]
iwlwifi: enhance testmode command sram_read
This patch enables SRAM read function to support entire target memory.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:29 +0000 (13:16 -0800)]
iwlwifi: update testmode command of direct register access
In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Jan 2012 21:16:28 +0000 (13:16 -0800)]
iwlwifi: Sanity check for sta_id
On my testing, I saw some strange behavior
[ 421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[ 421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode
not sure how it happen, but adding the sanity check to prevent memory
corruption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Jan 2012 21:16:27 +0000 (13:16 -0800)]
iwlwifi: don't process the info from uCode if does not has ownership
When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 6 Jan 2012 19:31:43 +0000 (11:31 -0800)]
rtlwifi: Simplify chip version id logging
Reduce object size a few KB too.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
584493 55333 126800 766626 bb2a2 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
pr_fmt() adds them. These are unnecessary and wrong.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 16:29:07 +0000 (08:29 -0800)]
rtlwifi: add CONFIG_RTLWIFI_DEBUG to remove all of the debug logging code
It does seem odd though to have a DBG_EMERG and not always
emit it.
What might also be useful for any embedded use is to add
CONFIG_RTLWIFI_DEBUG to conditionally remove all of the
debug logging code to reduce the largish object size.
This reduces the object size by about 1/3 (250KB)
when CONFIG_RTLWIFI_DEBUG is not set.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
368722 55333 94224 518279 7e887 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:45 +0000 (19:40 -0800)]
rtlwifi: Optimize RT_TRACE macro use of KBUILD_MODNAME for size
Moving the KBUILD_MODNAME to the format reduces the
overall object size a small amount.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.new
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:44 +0000 (19:40 -0800)]
rtlwifi: Remove duplicate __func__
The RT_TRACE macro already prepends it.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:43 +0000 (19:40 -0800)]
rtlwifi: Convert RT_ASSERT macro to use ##__VA_ARGS__
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RT_ASSERT parentheses.
Align arguments.
Coalesce formats.
Remove unnecessary __func__ use as the macro uses it.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.new
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.new
594841 55333 129680 779854 be64e drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:41 +0000 (19:40 -0800)]
rtlwifi: Convert RT_TRACE macro to use ##__VA_ARGS__
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RT_TRACE parentheses.
Miscellaneous typo and grammar fixes.
Add missing newlines to formats.
Remove duplicate KERN_DEBUG prefixes.
Coalesce formats.
Align arguments.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
594841 55333 129680 779854 be64e drivers/net/wireless/rtlwifi/built-in.o.new
607022 55333 138720 801075 c3933 drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:40 +0000 (19:40 -0800)]
rtlwifi: Standardize RT_PRINT_DATA macro and uses
Use a single printk(KERN_DEBUG to emit the header line
to avoid any possible output interleaving.
Remove unnecessary parentheses from the calling uses.
Standardize header arg without trailing \n or colon.
Fix a few pairwiase/pairwise typos.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use do {...} while (0) without terminating semicolons.
Add missing terminating semicolon to a few uses.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
All usage of ethtool_ops should be const; also add comma at end
of initializer list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / mv-sheeva.git / log