On a remount, the VFS layer will clear the MS_SYNCHRONOUS bit on the
assumption that the flags on the mount syscall will have it set if the
remounted fs is supposed to keep it.
In the case of "noac" though, MS_SYNCHRONOUS is implied. A remount of
such a mount will lose the MS_SYNCHRONOUS flag since "sync" isn't part
of the mount options.
Reported-by: Max Matveev <makc@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Azurit reports large increases in system time after 2.6.36 when running
Apache. It was bisected down to a892e2d7dcdfa6c76e6 ("vfs: use kmalloc()
to allocate fdmem if possible").
That patch caused the vfs to use kmalloc() for very large allocations and
this is causing excessive work (and presumably excessive reclaim) within
the page allocator.
Fix it by falling back to vmalloc() earlier - when the allocation attempt
would have been considered "costly" by reclaim.
For m68k, N_NORMAL_MEMORY represents all nodes that have present memory
since it does not support HIGHMEM. This patch sets the bit at the time
node_present_pages has been set by free_area_init_node.
At the time the node is brought online, the node state would have to be
done unconditionally since information about present memory has not yet
been recorded.
If N_NORMAL_MEMORY is not accurate, slub may encounter errors since it
uses this nodemask to setup per-cache kmem_cache_node data structures.
This pach is an alternative to the one proposed by David Rientjes
<rientjes@google.com> attempting to set node state immediately when
bringing the node online.
The huge_memory.c THP page fault was allowed to run if vm_ops was null
(which would succeed for /dev/zero MAP_PRIVATE, as the f_op->mmap wouldn't
setup a special vma->vm_ops and it would fallback to regular anonymous
memory) but other THP logics weren't fully activated for vmas with vm_file
not NULL (/dev/zero has a not NULL vma->vm_file).
So this removes the vm_file checks so that /dev/zero also can safely use
THP (the other albeit safer approach to fix this bug would have been to
prevent the THP initial page fault to run if vm_file was set).
After removing the vm_file checks, this also makes huge_memory.c stricter
in khugepaged for the DEBUG_VM=y case. It doesn't replace the vm_file
check with a is_pfn_mapping check (but it keeps checking for VM_PFNMAP
under VM_BUG_ON) because for a is_cow_mapping() mapping VM_PFNMAP should
only be allowed to exist before the first page fault, and in turn when
vma->anon_vma is null (so preventing khugepaged registration). So I tend
to think the previous comment saying if vm_file was set, VM_PFNMAP might
have been set and we could still be registered in khugepaged (despite
anon_vma was not NULL to be registered in khugepaged) was too paranoid.
The is_linear_pfn_mapping check is also I think superfluous (as described
by comment) but under DEBUG_VM it is safe to stay.
With transparent hugepage support, handle_mm_fault() has to be careful
that a normal PMD has been established before handling a PTE fault. To
achieve this, it used __pte_alloc() directly instead of pte_alloc_map as
pte_alloc_map is unsafe to run against a huge PMD. pte_offset_map() is
called once it is known the PMD is safe.
pte_alloc_map() is smart enough to check if a PTE is already present
before calling __pte_alloc but this check was lost. As a consequence,
PTEs may be allocated unnecessarily and the page table lock taken. Thi
useless PTE does get cleaned up but it's a performance hit which is
visible in page_test from aim9.
This patch simply re-adds the check normally done by pte_alloc_map to
check if the PTE needs to be allocated before taking the page table lock.
The effect is noticable in page_test from aim9.
(While this affects 2.6.38, it is a performance rather than a functional
bug and normally outside the rules -stable. While the big performance
differences are to a microbench, the difference in fork and exec
performance may be significant enough that -stable wants to consider the
patch)
Reported-by: Raz Ben Yehuda <raziebe@gmail.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PTE pages eat up memory just like anything else, but we do not account for
them in any way in the OOM scores. They are also _guaranteed_ to get
freed up when a process is OOM killed, while RSS is not.
This call was disabled as hot-unplugging one virtconsole port led to
another virtconsole port freezing.
Upon testing it again, this now works, so enable it.
In addition, a bug was found in qemu wherein removing a port of one type
caused the guest output from another port to stop working. I doubt it
was just this bug that caused it (since disabling the hvc_remove() call
did allow other ports to continue working), but since it's all solved
now, we're fine with hot-unplugging of virtconsole ports.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the warning about bad names for sys-fs and other kernel-things. The flexcop-pci driver was using '/'-characters in it, which is not good.
This has been fixed in several attempts by several people, but obviously never made it into the kernel.
When a DISCONTIGMEM memory range is brought online as a NUMA node, it
also needs to have its bet set in N_NORMAL_MEMORY. This is necessary for
generic kernel code that utilizes N_NORMAL_MEMORY as a subset of N_ONLINE
for memory savings.
These types of hacks can hopefully be removed once DISCONTIGMEM is either
removed or abstracted away from CONFIG_NUMA.
Fixes a panic in the slub code which only initializes structures for
N_NORMAL_MEMORY to save memory:
Slub makes assumptions about page_to_nid() which are violated by
DISCONTIGMEM and !NUMA. This violation results in a panic because
page_to_nid() can be non-zero for pages in the discontiguous ranges and
this leads to a null return by get_node(). The assertion by the
maintainer is that DISCONTIGMEM should only be allowed when NUMA is also
defined. However, at least six architectures: alpha, ia64, m32r, m68k,
mips, parisc violate this. The panic is a regression against slab, so
just mark slub broken in the problem configuration to prevent users
reporting these panics.
Acked-by: David Rientjes <rientjes@google.com> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is at least one BIOS with a DSDT containing a power resource
object with a _PR0 entry pointing back to that power resource. In
consequence, while registering that power resource
acpi_bus_get_power_flags() sees that it depends on itself and tries
to register it again, which leads to an infinitely deep recurrence.
This problem was introduced by commit bf325f9538d8c89312be305b9779e
(ACPI / PM: Register power resource devices as soon as they are
needed).
To fix this problem use the observation that power resources cannot
be power manageable and prevent acpi_bus_get_power_flags() from
being called for power resource objects.
References: https://bugzilla.kernel.org/show_bug.cgi?id=31872 Reported-and-tested-by: Pascal Dormeau <pdormeau@free.fr> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Len Brown <lenb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
f6649a7e "[S390] cleanup lowcore access from external interrupts" changed
handling of external interrupts. Instead of letting the external interrupt
handlers accessing the per cpu lowcore the entry code of the kernel reads
already all fields that are necessary and passes them to the handlers.
The pfault interrupt handler was incorrectly converted. It tries to
dereference a value which used to be a pointer to a lowcore field. After
the conversion however it is not anymore the pointer to the field but its
content. So instead of a dereference only a cast is needed to get the
task pointer that caused the pfault.
Fixes a NULL pointer dereference and a subsequent kernel crash:
From: Christian Borntraeger <borntraeger@de.ibm.com>
This patch fixes the sie exit on interrupts. The low level
interrupt handler returns to the PSW address in pt_regs and not
to the PSW address in the lowcore.
Without this fix a cpu bound guest might never leave guest state
since the host interrupt handler would blindly return to the
SIE instruction, even on need_resched and friends.
Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes UBIFS mount failure when the debugging support is enabled,
we are recovering from a power cut, we were first mounter R/O and we are
re-mounting R/W. In this case we should not assume that the amount of free
space before we have re-mounted R/W and after are equivalent, because
when we have mounted R/O the file-system is in a non-committed state so
the amount of free space is slightly smaller, due to the fact that we cannot
predict the amount of free space precisely before we commit.
This patch fixes the issue by skipping the debugging check in case of
recovery. This issue was reported by Caizhiyong <caizhiyong@huawei.com>
here: http://thread.gmane.org/gmane.linux.drivers.mtd/34350/focus=34387
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit da8aeb92 re-poked the battery on resume, but Linus reports that
it broke his eee and partially reverted it in b23fffd7. Unfortunately
this also results in my x201s giving crack values until the sysfs files
are poked again. In the revert message, it was suggested that we poke it
from a PM notifier, so let's do that.
With this in place, I haven't noticed the units going nutty on my
gnome-power-manager across a dozen suspends or so...
Signed-off-by: Kyle McMartin <kyle@redhat.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=25922
On ideapad Y530, the brightness key notify will be blocked if the last notify
is not responsed by getting the brightness value. Read value when we get the
notify shall fix the problem and will not have any difference on other ideapads.
Signed-off-by: Ike Panhc <ike.pan@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following symptoms:
1. Unmount UBIFS cleanly.
2. Start mounting UBIFS R/W and have a power cut immediately
3. Start mounting UBIFS R/O, this succeeds
4. Try to re-mount UBIFS R/W - this fails immediately or later on,
because UBIFS will write the master node to the flash area
which has been written before.
The analysis of the problem:
1. UBIFS is unmounted cleanly, both copies of the master node are clean.
2. UBIFS is being mounter R/W, starts changing master node copy 1, and
a power cut happens. The copy N1 becomes corrupted.
3. UBIFS is being mounted R/O. It notices the copy N1 is corrupted and
reads copy N2. Copy N2 is clean.
4. Because of R/O mode, UBIFS cannot recover copy 1.
5. The mount code (ubifs_mount()) sees that the master node is clean,
so it decides that no recovery is needed.
6. We are re-mounting R/W. UBIFS believes no recovery is needed and
starts updating the master node, but copy N1 is still corrupted
and was not recovered!
Fix this problem by marking the master node as dirty every time we
recover it and we are in R/O mode. This forces further recovery and
the UBIFS cleans-up the corruptions and recovers the copy N1 when
re-mounting R/W later.
Commit 40aee729b350 ('kconfig: fix default value for choice input')
fixed some cases where kconfig would select the wrong option from a
choice with a single valid option and thus enter an infinite loop.
However, this broke the test for user input of the form 'N?', because
when kconfig selects the single valid option the input is zero-length
and the test will read the byte before the input buffer. If this
happens to contain '?' (as it will in a mips build on Debian unstable
today) then kconfig again enters an infinite loop.
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acer laptops with ALC271x needs a magic initialization for digital-mic
to make it working with mono streams (and PulseAudio).
Added a fix-up applied to Acer with ALC271x generically.
Commit ce6120cc(ASoC: Decouple DAPM from CODECs) changed the signature of
snd_soc_dapm_widgets_new to take an pointer to a snd_soc_dapm_context instead of
a snd_soc_codec. The call to snd_soc_dapm_widgets_new in jz4740_codec_dev_probe
was not updated to reflect this change, which results in a compiletime warning
and a runtime OOPS.
Since the core code calls snd_soc_dapm_widgets_new after the codec has been
registered it can be dropped here.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If cts changes between reading the level at the cts input (USR1_RTSS)
and acking the irq (USR1_RTSD) the last edge doesn't generate an irq and
uart_handle_cts_change is called with a outdated value for cts.
This work perfectly for the case of GSM0 mode as gsm->received_fcs
contain the last piece of data required to generate final CRC.
gsm->received_fcs is not used for GSM1 mode. Thus we put an
additional byte to CRC calculation. As result we get a wrong CRC
and reject incoming frame.
During detect() we would probe the connection bits to determine if
there was a TV attached, and what video input type (Component, S-Video,
Composite, etc) to use. However, we promptly discarded this vital bit of
information and never propagated it to where it was used to determine
the correct modes and setup the control registers. Fix it!
Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.
This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
nouveau_bo_wr32 expects offset to be in words, but we pass value in bytes,
so after commit 73412c3854c877e5f37ad944ee8977addde4d35a ("drm/nouveau: allocate
kernel's notifier object at end of block") we started to overwrite some memory
after notifier buffer object (previously m2mf_ntfy was always 0, so it didn't
matter it was a value in bytes).
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net> Reported-by: Nigel Cunningham <lkml@nigelcunningham.com.au> Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Pekka Paalanen <pq@iki.fi> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we run out of domain_ids and fail iommu_attach_domain(), we
fall into domain_exit() without having setup enough of the
domain structure for this to do anything useful. In fact, it
typically runs off into the weeds walking the bogus domain->devices
list. Just free the domain.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Donald Dutile <ddutile@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we remove a device, we unlink the iommu from the domain, but
we never do the reverse unlinking of the domain from the iommu.
This means that we never clear iommu->domain_ids, eventually leading
to resource exhaustion if we repeatedly bind and unbind a device
to a driver. Also free empty domains to avoid a resource leak.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Donald Dutile <ddutile@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
When detaching a buffer from a vq, the avail.idx value should be
decremented as well.
This was noticed by hot-unplugging a virtio console port and then
plugging in a new one on the same number (re-using the vqs which were
just 'disowned'). qemu reported
'Guest moved used index from 0 to 256'
when any IO was attempted on the new port.
Reported-by: juzhang <juzhang@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The above patch breaks free path for stp->st_file. If stp was inserted
into sop->so_stateids, we have to free stp->st_file refcount. Because
stp->st_file refcount itself is taken whether or not any refcounts are
taken on the stp->st_file->fi_fds[].
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Gerhard Heift <ml-nfs-linux-20110412-ef47@gheift.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Jason Conti <jason.conti@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Reported-by: Joe Culler <joe.culler@gmail.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scot Doyle demonstrated ip_options_compile() could be called with an skb
without an attached route, using a setup involving a bridge, netfilter,
and forged IP packets.
Let's make ip_options_compile() and ip_options_rcv_srr() a bit more
robust, instead of changing bridge/netfilter code.
With help from Hiroaki SHIMODA.
Reported-by: Scot Doyle <lkml@scotdoyle.com> Tested-by: Scot Doyle <lkml@scotdoyle.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 462fb2af9788a82 (bridge : Sanitize skb before it enters the IP
stack), missed one IPCB init before calling ip_options_compile()
Thanks to Scot Doyle for his tests and bug reports.
Reported-by: Scot Doyle <lkml@scotdoyle.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Acked-by: Bandan Das <bandan.das@stratus.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Cc: Jan Lübbe <jluebbe@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
GCC 4.6.0 in Fedora rawhide turned up some compile errors in tools/perf
due to the -Werror=unused-but-set-variable flag.
I've gone through and annotated some of the assignments that had side
effects (ie: return value from a function) with the __used annotation,
and in some cases, just removed unused code.
In a few cases, we were assigning something useful, but not using it in
later parts of the function.
kyle@dreadnought:~/src% gcc --version
gcc (GCC) 4.6.0 20110122 (Red Hat 4.6.0-0.3)
Cc: Ingo Molnar <mingo@redhat.com>
LKML-Reference: <20110124161304.GK27353@bombadil.infradead.org> Signed-off-by: Kyle McMartin <kyle@redhat.com>
[ committer note: Fixed up the annotation fixes, as that code moved recently ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Backported to 2.6.38.2 by deleting unused but set variables] Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com> Reported-by: Justin P. Mattock <justinmattock@gmail.com> Reported-by: Ed Tomlinson <edt@aei.ca> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Tested-by: Justin P. Mattock <justinmattock@gmail.com> Tested-by: Mikko Vinni <mmvinni@yahoo.com> Tested-by: Ed Tomlinson <edt@aei.ca>
This is necessary even with PCI(e) GART, and it makes writeback work even with
AGP on my PowerBook. Might still be unreliable with older revisions of UniNorth
and other AGP bridges though.
Signed-off-by: Michel Dänzer <daenzer@vmware.com> Reviewed-by: Alex Deucher <alex.deucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If I unplug a device while the UAS driver is loaded, I get an oops
in usb_free_streams(). This is because usb_unbind_interface() calls
usb_disable_interface() which calls usb_disable_endpoint() which sets
ep_out and ep_in to NULL. Then the UAS driver calls usb_pipe_endpoint()
which returns a NULL pointer and passes an array of NULL pointers to
usb_free_streams().
I think the correct fix for this is to check for the NULL pointer
in usb_free_streams() rather than making the driver check for this
situation. My original patch for this checked for dev->state ==
USB_STATE_NOTATTACHED, but the call to usb_disable_interface() is
conditional, so not all drivers would want this check.
Note from Sarah Sharp: This patch does avoid a potential dereference,
but the real fix (which will be implemented later) is to set the
.soft_unbind flag in the usb_driver structure for the UAS driver, and
all drivers that allocate streams. The driver should free any streams
when it is unbound from the interface. This avoids leaking stream rings
in the xHCI driver when usb_disable_interface() is called.
This should be queued for stable trees back to 2.6.35.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, when resetting a device, xHCI driver disables all but one
endpoints and frees their rings, but leaves alone any streams that
might have been allocated. Later, when users try to free allocated
streams, we oops in xhci_setup_no_streams_ep_input_ctx() because
ep->ring is NULL.
Let's free not only rings but also stream data as well, so that
calling free_streams() on a device that was reset will be safe.
This should be queued for stable trees back to 2.6.35.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com> Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com> Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
next_pidmap() just quietly accepted whatever 'last' pid that was passed
in, which is not all that safe when one of the users is /proc.
Admittedly the proc code should do some sanity checking on the range
(and that will be the next commit), but that doesn't mean that the
helper functions should just do that pidmap pointer arithmetic without
checking the range of its arguments.
So clamp 'last' to PID_MAX_LIMIT. The fact that we then do "last+1"
doesn't really matter, the for-loop does check against the end of the
pidmap array properly (it's only the actual pointer arithmetic overflow
case we need to worry about, and going one bit beyond isn't going to
overflow).
[ Use PID_MAX_LIMIT rather than pid_max as per Eric Biederman ]
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com> Analyzed-by: Robert Święcki <robert@swiecki.net> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
5520e89 ("brk: fix min_brk lower bound computation for COMPAT_BRK")
tried to get the whole logic of brk randomization for legacy
(libc5-based) applications finally right.
It turns out that the way to detect whether brk has actually been
randomized in the end or not introduced by that patch still doesn't work
for those binaries, as reported by Geert:
: /sbin/init from my old m68k ramdisk exists prematurely.
:
: Before the patch:
:
: | brk(0x80005c8e) = 0x80006000
:
: After the patch:
:
: | brk(0x80005c8e) = 0x80005c8e
:
: Old libc5 considers brk() to have failed if the return value is not
: identical to the requested value.
I don't like it, but currently see no better option than a bit flag in
task_struct to catch the CONFIG_COMPAT_BRK && randomize_va_space == 2
case.
Two years later, I've found obvious meaningless code fragment and
restored original intention by following commit.
2010 Jun 04; commit bb21c7ce; vmscan: fix do_try_to_free_pages()
return value when priority==0
But, the logic didn't works when 32bit highmem system goes hibernation
and Minchan slightly changed the algorithm and fixed it .
2010 Sep 22: commit d1908362: vmscan: check all_unreclaimable
in direct reclaim path
But, recently, Andrey Vagin found the new corner case. Look,
struct zone {
..
int all_unreclaimable;
..
unsigned long pages_scanned;
..
}
zone->all_unreclaimable and zone->pages_scanned are neigher atomic
variables nor protected by lock. Therefore zones can become a state of
zone->page_scanned=0 and zone->all_unreclaimable=1. In this case, current
all_unreclaimable() return false even though zone->all_unreclaimabe=1.
This resulted in the kernel hanging up when executing a loop of the form
as described in
http://www.gossamer-threads.com/lists/linux/kernel/1348725#1348725
Is this ignorable minor issue? No. Unfortunately, x86 has very small dma
zone and it become zone->all_unreclamble=1 easily. and if it become
all_unreclaimable=1, it never restore all_unreclaimable=0. Why? if
all_unreclaimable=1, vmscan only try DEF_PRIORITY reclaim and
a-few-lru-pages>>DEF_PRIORITY always makes 0. that mean no page scan at
all!
Eventually, oom-killer never works on such systems. That said, we can't
use zone->pages_scanned for this purpose. This patch restore
all_unreclaimable() use zone->all_unreclaimable as old. and in addition,
to add oom_killer_disabled check to avoid reintroduce the issue of commit d1908362 ("vmscan: check all_unreclaimable in direct reclaim path").
Reported-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Nick Piggin <npiggin@kernel.dk> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scheduler load balancer has specific code to deal with cases of
unbalanced system due to lots of unmovable tasks (for example because of
hard CPU affinity). In those situation, it excludes the busiest CPU that
has pinned tasks for load balance consideration such that it can perform
second 2nd load balance pass on the rest of the system.
This all works as designed if there is only one cgroup in the system.
However, when we have multiple cgroups, this logic has false positives and
triggers multiple load balance passes despite there are actually no pinned
tasks at all.
The reason it has false positives is that the all pinned logic is deep in
the lowest function of can_migrate_task() and is too low level:
load_balance_fair() iterates each task group and calls balance_tasks() to
migrate target load. Along the way, balance_tasks() will also set a
all_pinned variable. Given that task-groups are iterated, this all_pinned
variable is essentially the status of last group in the scanning process.
Task group can have number of reasons that no load being migrated, none
due to cpu affinity. However, this status bit is being propagated back up
to the higher level load_balance(), which incorrectly think that no tasks
were moved. It kick off the all pinned logic and start multiple passes
attempt to move load onto puller CPU.
To fix this, move the all_pinned aggregation up at the iterator level.
This ensures that the status is aggregated over all task-groups, not just
last one in the list.
The new bfin_rtc_alarm_irq_enable function forgot to add a "return 0" to
the end leading to the build warning:
drivers/rtc/rtc-bfin.c: In function 'bfin_rtc_alarm_irq_enable':
drivers/rtc/rtc-bfin.c:253: warning: control reaches end of non-void function
CC: Thomas Gleixner <tglx@linutronix.de> CC: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During RCU walk in path_lookupat and path_openat, the rcu lookup
frequently failed if looking up an absolute path, because when root
directory was looked up, seq number was not properly set in nameidata.
We dropped out of RCU walk in nameidata_drop_rcu due to mismatch in
directory entry's seq number. We reverted to slow path walk that need
to take references.
With the following patch, I saw a 50% increase in an exim mail server
benchmark throughput on a 4-socket Nehalem-EX system.
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for Always Running APIC timer (ARAT) was introduced in
commit db954b5898dd3ef3ef93f4144158ea8f97deb058. This feature
allows us to avoid switching timers from LAPIC to something else
(e.g. HPET) and go into timer broadcasts when entering deep
C-states.
AMD processors don't provide a CPUID bit for that feature but
they also keep APIC timers running in deep C-states (except for
cases when the processor is affected by erratum 400). Therefore
we should set ARAT feature bit on AMD CPUs.
Tested-by: Borislav Petkov <borislav.petkov@amd.com> Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com> Acked-by: Mark Langsdorf <mark.langsdorf@amd.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
LKML-Reference: <1300205624-4813-1-git-send-email-ostr@amd64.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes severe UBIFS bug: UBIFS oopses when we 'fsync()' an
file on R/O-mounter file-system. We (the UBIFS authors) incorrectly
thought that VFS would not propagate 'fsync()' down to the file-system
if it is read-only, but this is not the case.
It is easy to exploit this bug using the following simple perl script:
use strict;
use File::Sync qw(fsync sync);
die "File path is not specified" if not defined $ARGV[0];
my $path = $ARGV[0];
open FILE, "<", "$path" or die "Cannot open $path: $!";
fsync(\*FILE) or die "cannot fsync $path: $!";
close FILE or die "Cannot close $path: $!";
Thanks to Reuben Dowle <Reuben.Dowle@navico.com> for reporting about this
issue.
This is an almost-revert of commit 93b43fa ("oom: give the dying task a
higher priority").
That commit dramatically improved oom killer logic when a fork-bomb
occurs. But I've found that it has nasty corner case. Now cpu cgroup has
strange default RT runtime. It's 0! That said, if a process under cpu
cgroup promote RT scheduling class, the process never run at all.
If an admin inserts a !RT process into a cpu cgroup by setting
rtruntime=0, usually it runs perfectly because a !RT task isn't affected
by the rtruntime knob. But if it promotes an RT task via an explicit
setscheduler() syscall or an OOM, the task can't run at all. In short,
the oom killer doesn't work at all if admins are using cpu cgroup and don't
touch the rtruntime knob.
Eventually, kernel may hang up when oom kill occur. I and the original
author Luis agreed to disable this logic.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Luis Claudio R. Goncalves <lclaudio@uudg.org> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On no-mmu arch, there is a memleak during shmem test. The cause of this
memleak is ramfs_nommu_expand_for_mapping() added page refcount to 2
which makes iput() can't free that pages.
The simple test file is like this:
int main(void)
{
int i;
key_t k = ftok("/etc", 42);
for ( i=0; i<100; ++i) {
int id = shmget(k, 10000, 0644|IPC_CREAT);
if (id == -1) {
printf("shmget error\n");
}
if(shmctl(id, IPC_RMID, NULL ) == -1) {
printf("shm rm error\n");
return -1;
}
}
printf("run ok...\n");
return 0;
}
And the result:
root:/> free
total used free shared buffers
Mem: 60320 17912 42408 0 0
-/+ buffers: 17912 42408
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 19096 41224 0 0
-/+ buffers: 19096 41224
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 20296 40024 0 0
-/+ buffers: 20296 40024
...
After this patch the test result is:(no memleak anymore)
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
Signed-off-by: Bob Liu <lliubbo@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The conventional format for boolean attributes in sysfs is numeric ("0" or
"1" followed by new-line). Any boolean attribute can then be read and
written using a generic function. Using the strings "yes [no]", "[yes]
no" (read), "yes" and "no" (write) will frustrate this.
[akpm@linux-foundation.org: use kstrtoul()]
[akpm@linux-foundation.org: test_bit() doesn't return 1/0, per Neil] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Hugh Dickins <hughd@google.com> Tested-by: David Rientjes <rientjes@google.com> Cc: NeilBrown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. simple_strto*() do not contain overflow checks and crufty,
libc way to indicate failure.
2. strict_strto*() also do not have overflow checks but the name and
comments pretend they do.
3. Both families have only "long long" and "long" variants,
but users want strtou8()
4. Both "simple" and "strict" prefixes are wrong:
Simple doesn't exactly say what's so simple, strict should not exist
because conversion should be strict by default.
The solution is to use "k" prefix and add convertors for more types.
Enter
kstrtoull()
kstrtoll()
kstrtoul()
kstrtol()
kstrtouint()
kstrtoint()
Include runtime testsuite (somewhat incomplete) as well.
strict_strto*() become deprecated, stubbed to kstrto*() and
eventually will be removed altogether.
Use kstrto*() in code today!
Note: on some archs _kstrtoul() and _kstrtol() are left in tree, even if
they'll be unused at runtime. This is temporarily solution,
because I don't want to hardcode list of archs where these
functions aren't needed. Current solution with sizeof() and
__alignof__ at least always works.
The FLAGS_HAS_TIMEOUT flag was not getting set, causing the restart_block to
restart futex_wait() without a timeout after a signal.
Commit b41277dc7a18ee332d in 2.6.38 introduced the regression by accidentally
removing the the FLAGS_HAS_TIMEOUT assignment from futex_wait() during the setup
of the restart block. Restore the originaly behavior.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=32922 Reported-by: Tim Smith <tsmith201104@yahoo.com> Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Kacur <jkacur@redhat.com> Link: http://lkml.kernel.org/r/%3Cdaac0eb3af607f72b9a4d3126b2ba8fb5ed3b883.1302820917.git.dvhart%40linux.intel.com%3E Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the warnings emitted (we fail arch/sparc file
builds with -Werror) were legitimate but harmless, however
one case (n2_pcr_write) was a genuine bug.
Based almost entirely upon a patch by Sam Ravnborg.
Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does. In binutils 2.21 these are treated
as errors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Whenever we enter the IP stack proper from bridge netfilter we
need to ensure that the skb is in a form the IP stack expects
it to be in.
The entry point on NF_FORWARD did not meet the requirements of
the IP stack, therefore leading to potential crashes/panics.
This patch fixes the problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c95b819ad7 (gre: Use needed_headroom)
made gre use needed_headroom instead of hard_header_len
This uncover a bug in vlan code.
We should make sure vlan devices take into account their
real_dev->needed_headroom or we risk a crash in ipgre_header(), because
we dont have enough room to push IP header in skb.
Reported-by: Diddi Oscarsson <diddi@diddi.se> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We return a destination entry without refcount if a socket
policy is found in xfrm_lookup. This triggers a warning on
a negative refcount when freeeing this dst entry. So take
a refcount in this case to fix it.
This refcount was forgotten when xfrm changed to cache bundles
instead of policies for outgoing flows.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the current undo logic, cwnd is moderated after it was restored
to the value prior entering fast-recovery. It was moderated first
in tcp_try_undo_recovery then again in tcp_complete_cwr.
Since the undo indicates recovery was false, these moderations
are not necessary. If the undo is triggered when most of the
outstanding data have been acknowledged, the (restored) cwnd is
falsely pulled down to a small value.
This patch removes these cwnd moderations if cwnd is undone
a) during fast-recovery
b) by receiving DSACKs past fast-recovery
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like DCCP and other similar pieces of code, there are mechanisms
here to try allocating smaller hash tables if the allocation
fails. So pass in __GFP_NOWARN like the others do instead of
emitting a scary message.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Signed-off-by: Dan Siemon <dan@coverfire.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Dave Täht <d@taht.net> Cc: Jonathan Morton <chromatix99@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I was fixing issues with unregisgtering tables under /proc/sys/net/ipv6/neigh
by adding a mount point it appears I missed a critical ordering issue, in the
ipv6 initialization. I had not realized that ipv6_sysctl_register is called
at the very end of the ipv6 initialization and in particular after we call
neigh_sysctl_register from ndisc_init.
"neigh" needs to be initialized in ipv6_static_sysctl_register which is
the first ipv6 table to initialized, and definitely before ndisc_init.
This removes the weirdness of duplicate tables while still providing a
"neigh" mount point which prevents races in sysctl unregistering.
This was initially reported at https://bugzilla.kernel.org/show_bug.cgi?id=31232 Reported-by: sunkan@zappa.cx Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A struct used in the l2tp_eth driver for registering network namespace
ops was incorrectly marked as __net_initdata, leading to oops when
module unloaded.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As specified by errata eTSEC49 of MPC8548 and errata eTSEC12 of MPC83xx,
older revisions of gianfar controllers will be unable to calculate a TCP/UDP
packet checksum for some alignments of the appropriate FCB. This patch checks
for FCB alignment on such controllers and falls back to software checksumming
if the alignment is known to be bad.
Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log