After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:
* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
dependency issues that arise with trying to remove the connector from
sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good
This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:
[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi
And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.
To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.
The SPICE protocol considers the position of a cursor to be the location
of its active pixel on the display, so the cursor is drawn with its
top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor
position gives the location where the top-left corner should be drawn,
with the hotspot being a hint for drivers that need it.
This fixes the location of the window resize cursors when using Fluxbox
with the QXL DRM driver and both the QXL and modesetting X drivers.
Most calls to nvkm_ramht_new use 0x8000 as the size. This results in a
fairly sizeable chunk of memory to be allocated, which may not be
available with kzalloc. Since this is done fairly rarely (once per
channel), use vzalloc instead.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise an incoming waker on the dest hash bucket can miss
the waiter adding itself to the plist during the lockless
check optimization (small window but still the correct way
of doing this); similarly to the decrement counterpart.
If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0
transition in user space first then the user space value might not have the
waiters bit set. This opens the following race:
So the cmpxchg fails and returns -EINVAL to user space, which is wrong because
the futex value is valid.
To handle this (yes, yet another) corner case gracefully, check for a flag
change and retry.
[ tglx: Massaged changelog and slightly reworked implementation ]
Fixes: ccf9e6a80d9e ("futex: Make unlock_pi more robust") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent decoupling of pagefault disable and preempt disable added an
explicit preempt_disable/enable() pair to the futex_atomic_cmpxchg_inatomic()
implementation in asm-generic/futex.h. But it forgot to add preempt_enable()
calls to the error handling code pathes, which results in a preemption count
imbalance.
This is observable on boot when the test for atomic_cmpxchg() is calling
futex_atomic_cmpxchg_inatomic() on a NULL pointer.
Add the missing preempt_enable() calls to the error handling code pathes.
[ tglx: Massaged changelog ]
Fixes: d9b9ff8c1889 ("sched/preempt, futex: Disable preemption in UP futex_atomic_cmpxchg_inatomic() explicitly") Signed-off-by: Romain Perier <romain.perier@free-electrons.com> Cc: linux-arch@vger.kernel.org Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1460640963-690-1-git-send-email-romain.perier@free-electrons.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [9bef72bdb26e: ALSA: pcxhr: Use nonatomic PCM ops]
converted to non-atomic PCM ops, but shamelessly with an unbalanced
mutex locking, which leads to the hangup easily. Fix it.
Although one weird behavior about the input path (inconsistent D0/D3
switch) on Cirrus CS420x codecs was fixed in the previous commit,
there is still an issue on some Mac machines: the capture stream
stalls when switching the ADCs on the fly. More badly, this keeps
stuck until the next reboot.
The dynamic ADC switching is already a bit fragile and assuming
optimistically that the chip accepts the frequent power changes. On
Cirrus codecs, this doesn't seem applicable.
As a quick workaround, we pin down the ADCs to keep up in D0 when
spec->dyn_adc_switch is set. In this way, the ADCs are kept up only
for the system that were confirmed to be broken.
The Optiplex 9020m with Haswell-DT processor needs a quirk for the
headset jack at the front of the machine to be able to use microphones.
A quirk for this model was originally added in 3127899, but c77900e
removed it in favour of a more generic version.
Unfortunately, pin configurations can changed based on firmware/BIOS
versions, and the generic version doesn't have any effect on newer
versions of the machine/firmware anymore.
With help from David Henningsson <diwic@ubuntu.com>
We've got a regression report that the recording on Mac with a cirrus
codec doesn't work any longer. This turned out to be the missing
power up to D0 by power_save_node enablement.
After analyzing the traces, we found out that the culprit is that the
codec advertises the "actual" power state of a few nodes to be D0
while the "target" power state is D3. This inconsistency is usually
OK, as it implies the power transition. But in the case of cirrus
codec, this seems to be stuck to D3 while it's not actually D0.
This patch addresses the issue by checking the power state difference
more strictly. It sends the power-state change verb unless both the
target and the actual power states show the given value.
We may introduce yet another flag indicating the possible broken
hardware power state, but it's anyway safer to set the proper power
state even in a transition (at least it's harmless as long as the
target state is same). So this simpler change was applied now.
eb1af3b71f9d ("Fix computation of channel address")
I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.
Tested-by: Patrick Geary <patrickg@supermicro.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Fixes: eb1af3b71f9d ("Fix computation of channel address") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:
The set_pte_at() function must update the hardware PTE_RDONLY bit
depending on the state of the PTE_WRITE and PTE_DIRTY bits of the given
entry value. However, it currently only performs this for pte_valid()
entries, ignoring PTE_PROT_NONE. The side-effect is that PROT_NONE
mappings would not have the PTE_RDONLY bit set. Without
CONFIG_ARM64_HW_AFDBM, this is not an issue since such PROT_NONE pages
are not accessible anyway.
With commit 2f4b829c625e ("arm64: Add support for hardware updates of
the access and dirty pte bits"), the ptep_set_wrprotect() function was
re-written to cope with automatic hardware updates of the dirty state.
As an optimisation, only PTE_RDONLY is checked to assess the "dirty"
status. Since set_pte_at() does not set this bit for PROT_NONE mappings,
such pages may be considered "dirty" as a result of
ptep_set_wrprotect().
This patch updates the pte_valid() check to pte_present() in
set_pte_at(). It also adds PTE_PROT_NONE to the swap entry bits comment.
Fixes: 2f4b829c625e ("arm64: Add support for hardware updates of the access and dirty pte bits") Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com> Tested-by: Ganapatrao Kulkarni <gkulkarni@cavium.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, set_pte_at() only checks the software PTE_WRITE bit for user
mappings when it sets or clears the hardware PTE_RDONLY accordingly. The
kernel ptes are written directly without any modification, relying
solely on the protection bits in macros like PAGE_KERNEL. However,
modifying kernel pte attributes via pte_wrprotect() would be ignored by
set_pte_at(). Since pte_wrprotect() does not set PTE_RDONLY (it only
clears PTE_WRITE), the new permission is not taken into account.
This patch changes set_pte_at() to adjust the read-only permission for
kernel ptes as well. As a side effect, existing PROT_* definitions used
for kernel ioremap*() need to include PTE_DIRTY | PTE_WRITE.
(additionally, white space fix for PTE_KERNEL_ROX)
The CPU controller hasn't kept up with the various changes in the whole
cgroup initialization / destruction sequence, and commit:
2e91fa7f6d45 ("cgroup: keep zombies associated with their original cgroups")
caused it to explode.
The reason for this is that zombies do not inhibit css_offline() from
being called, but do stall css_released(). Now we tear down the cfs_rq
structures on css_offline() but zombies can run after that, leading to
use-after-free issues.
The solution is to move the tear-down to css_released(), which
guarantees nobody (including no zombies) is still using our cgroup.
Furthermore, a few simple cleanups are possible too. There doesn't
appear to be any point to us using css_online() (anymore?) so fold that
in css_alloc().
And since cgroup code guarantees an RCU grace period between
css_released() and css_free() we can forgo using call_rcu() and free the
stuff immediately.
Suggested-by: Tejun Heo <tj@kernel.org> Reported-by: Kazuki Yamaguchi <k@rhe.jp> Reported-by: Niklas Cassel <niklas.cassel@axis.com> Tested-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Tejun Heo <tj@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 2e91fa7f6d45 ("cgroup: keep zombies associated with their original cgroups") Link: http://lkml.kernel.org/r/20160316152245.GY6344@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current number of requestor lines is limited to 31. This was an
error of a previous commit, as this number is platform dependent, and is
actually :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
The previous testing did not reveal the faulty constant as on pxa[23]xx
platforms, only camera, MSL and USB are above requestor 32, and in these
only the camera has a driver using dma.
Fixes: e87ffbdf0697 ("dmaengine: pxa_dma: fix the no-requestor case") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a typo in documentation regarding to descriptor empty bit (DESCE)
which is set to 1 when descriptor is empty. Thus, status register at the end of
a transfer usually returns all DESCE bits set and thus it will never be zero.
Moreover, there are 2 bits (CDESC) that encode current descriptor, on which
interrupt has been asserted. In case when we have few descriptors programmed we
might have non-zero value.
Remove DESCE and CDESC bits from DMA channel status register (HSU_CH_SR) when
reading it.
The commit 895005202987 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 895005202987 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with 4.1 the tracing subsystem has its own filesystem
which is automounted in the tracing subdirectory of debugfs.
Prior to this debugfs could be bind mounted in a cloned mount
namespace, but if tracefs has been mounted under debugfs this
now fails because there is a locked child mount. This creates
a regression for container software which bind mounts debugfs
to satisfy the assumption of some userspace software.
In other pseudo filesystems such as proc and sysfs we're already
creating mountpoints like this in such a way that no dirents can
be created in the directories, allowing them to be exceptions to
some MNT_LOCKED tests. In fact we're already do this for the
tracefs mountpoint in sysfs.
Do the same in debugfs_create_automount(), since the intention
here is clearly to create a mountpoint. This fixes the regression,
as locked child mounts on permanently empty directories do not
cause a bind mount to fail.
Based on Sergey's test patch [1], this fixes zram with lz4 compression
on big endian cpus.
Note that the 64-bit preprocessor test is not a cleanup, it's part of
the fix, since those identifiers are bogus (for example, __ppc64__
isn't defined anywhere else in the kernel, which means we'd fall into
the 32-bit definitions on ppc64).
Commit 9567366fefdd ("dm cache metadata: fix READ_LOCK macros and
cleanup WRITE_LOCK macros") uses down_write() instead of down_read() in
cmd_read_lock(), yet up_read() is used to release the lock in
READ_UNLOCK(). Fix it.
Fixes: 9567366fefdd ("dm cache metadata: fix READ_LOCK macros and cleanup WRITE_LOCK macros") Signed-off-by: Ahmed Samy <f.fallen45@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The READ_LOCK macro was incorrectly returning -EINVAL if
dm_bm_is_read_only() was true -- it will always be true once the cache
metadata transitions to read-only by dm_cache_metadata_set_read_only().
Wrap READ_LOCK and WRITE_LOCK multi-statement macros in do {} while(0).
Also, all accesses of the 'cmd' argument passed to these related macros
are now encapsulated in parenthesis.
A follow-up patch can be developed to eliminate the use of macros in
favor of pure C code. Avoiding that now given that this needs to apply
to stable@.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Fixes: d14fcf3dd79 ("dm cache: make sure every metadata function checks fail_io") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Changes since V1: fixed the description and added KASan warning.
In assoc_array_insert_into_terminal_node(), we call the
compare_object() method on all non-empty slots, even when they're
not leaves, passing a pointer to an unexpected structure to
compare_object(). Currently it causes an out-of-bound read access
in keyring_compare_object detected by KASan (see below). The issue
is easily reproduced with keyutils testsuite.
Only call compare_object() when the slot is a leave.
KASan warning:
==================================================================
BUG: KASAN: slab-out-of-bounds in keyring_compare_object+0x213/0x240 at addr ffff880060a6f838
Read of size 8 by task keyctl/1655
=============================================================================
BUG kmalloc-192 (Not tainted): kasan: bad access detected
-----------------------------------------------------------------------------
Commit 127500ccb766f ("ARM: OMAP2+: Only write the sysconfig on idle
when necessary") talks about verification of sysconfig cache value before
updating it, only during idle path. But the patch is adding the
verification in the enable path. So, adding the check in a proper place
as per the commit description.
Not keeping this check during enable path as there is a chance of losing
context and it is safe to do on idle as the context of the register will
never be lost while the device is active.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Cc: Jon Hunter <jonathanh@nvidia.com> Fixes: commit 127500ccb766 "ARM: OMAP2+: Only write the sysconfig on idle when necessary"
[paul@pwsan.com: appears to have been caused by my own mismerge of the
originally posted patch] Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commits:
commit 3fa609755c11 ("ARM: omap2: restore OMAP4 barrier behaviour")
commit f746929ffdc8 ("Revert "ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688"")
and
commit ea827ad5ffbb ("ARM: DRA7: Provide proper IO map table")
came in around the same time, unfortunately this seem to have missed
initializing the barrier for DRA7 platforms - omap5_map_io was reused
for dra7 till it was split out by the last patch. barrier_init
needs to be hence carried forward as it is valid for DRA7 family of
processors as they are for OMAP5.
Fixes: ea827ad5ffbb7 ("ARM: DRA7: Provide proper IO map table") Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2 port for Armada 38x is defined to be at 58000, not at
50000.
Fixes: 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS devices") Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org> Acked-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55ee7017ee31 ("arm: omap2: board-generic: use omap4_local_timer_init
for AM437x") makes synctimer32k as the clocksource on AM43xx. By default
the synctimer32k is clocked by 32K RTC OSC on AM43xx. But this 32K RTC OSC
is not available on epos boards which makes it fail to boot.
Synctimer32k can also be clocked by a peripheral PLL, so making this as
clock parent for synctimer3k on epos boards.
Fixes: 55ee7017ee31 ("arm: omap2: board-generic: use omap4_local_timer_init for AM437x") Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a host that runs NTP, corrections can have a direct impact on
the background timer that we program on the behalf of a vcpu.
In particular, NTP performing a forward correction will result in
a timer expiring sooner than expected from a guest point of view.
Not a big deal, we kick the vcpu anyway.
But on wake-up, the vcpu thread is going to perform a check to
find out whether or not it should block. And at that point, the
timer check is going to say "timer has not expired yet, go back
to sleep". This results in the timer event being lost forever.
There are multiple ways to handle this. One would be record that
the timer has expired and let kvm_cpu_has_pending_timer return
true in that case, but that would be fairly invasive. Another is
to check for the "short sleep" condition in the hrtimer callback,
and restart the timer for the remaining time when the condition
is detected.
This patch implements the latter, with a bit of refactoring in
order to avoid too much code duplication.
Reported-by: Alexander Graf <agraf@suse.de> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An interrupt handler that uses the fpu can kill a KVM VM, if it runs
under the following conditions:
- the guest's xcr0 register is loaded on the cpu
- the guest's fpu context is not loaded
- the host is using eagerfpu
Note that the guest's xcr0 register and fpu context are not loaded as
part of the atomic world switch into "guest mode". They are loaded by
KVM while the cpu is still in "host mode".
Usage of the fpu in interrupt context is gated by irq_fpu_usable(). The
interrupt handler will look something like this:
if (irq_fpu_usable()) {
kernel_fpu_begin();
[... code that uses the fpu ...]
kernel_fpu_end();
}
As long as the guest's fpu is not loaded and the host is using eager
fpu, irq_fpu_usable() returns true (interrupted_kernel_fpu_idle()
returns true). The interrupt handler proceeds to use the fpu with
the guest's xcr0 live.
kernel_fpu_begin() saves the current fpu context. If this uses
XSAVE[OPT], it may leave the xsave area in an undesirable state.
According to the SDM, during XSAVE bit i of XSTATE_BV is not modified
if bit i is 0 in xcr0. So it's possible that XSTATE_BV[i] == 1 and
xcr0[i] == 0 following an XSAVE.
kernel_fpu_end() restores the fpu context. Now if any bit i in
XSTATE_BV == 1 while xcr0[i] == 0, XRSTOR generates a #GP. The
fault is trapped and SIGSEGV is delivered to the current process.
Only pre-4.2 kernels appear to be vulnerable to this sequence of
events. Commit 653f52c ("kvm,x86: load guest FPU context more eagerly")
from 4.2 forces the guest's fpu to always be loaded on eagerfpu hosts.
This patch fixes the bug by keeping the host's xcr0 loaded outside
of the interrupts-disabled region where KVM switches into guest mode.
Suggested-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: David Matlack <dmatlack@google.com>
[Move load after goto cancel_injection. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we loop over all queued machine check error records to pass them
to the registered notifiers we use llist_for_each_entry(). But the loop
calls gen_pool_free() for the entry in the body of the loop - and then
the iterator looks at node->next after the free.
Use llist_for_each_entry_safe() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Gong Chen <gong.chen@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/0205920@agluck-desk.sc.intel.com Link: http://lkml.kernel.org/r/1459929916-12852-4-git-send-email-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from commit e36f620428(block: split bios to max possible length),
block core starts to split bio in the middle of bvec.
Unfortunately loop dio/aio doesn't consider this situation, and
always treat 'iter.iov_offset' as zero. Then filesystem corruption
is observed.
This patch figures out the offset of the base bvevc via
'bio->bi_iter.bi_bvec_done' and fixes the issue by passing the offset
to iov iterator.
Fixes: e36f6204288088f (block: split bios to max possible length) Cc: Keith Busch <keith.busch@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initialization of partition's percpu_ref should have been done before
sending out KOBJ_ADD uevent, which may cause userspace to read partition
table. So the uninitialized percpu_ref may be accessed in data path.
This upstream commit is causing an oops: d8f00cd685f5 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com> Cc: Du, Changbin <changbin.du@intel.com> Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbvision driver crashes when a specially crafted usb device with invalid
number of interfaces or endpoints is detected. This fix adds checks that the
device has proper configuration expected by the driver.
991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") appeared in v4.3 and helps support IOAPIC hotplug.
Олег reported that the Elcus-1553 TA1-PCI driver worked in v4.2 but not
v4.3 and bisected it to 991de2e59090. Sunjin reported that the RocketRAID
272x driver worked in v4.2 but not v4.3. In both cases booting with
"pci=routirq" is a workaround.
I think the problem is that after 991de2e59090, we no longer call
pcibios_enable_irq() for upstream bridges. Prior to 991de2e59090, when a
driver called pci_enable_device(), we recursively called
pcibios_enable_irq() for upstream bridges via pci_enable_bridge().
After 991de2e59090, we call pcibios_enable_irq() from pci_device_probe()
instead of the pci_enable_device() path, which does *not* call
pcibios_enable_irq() for upstream bridges.
Revert 991de2e59090 to fix these driver regressions.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211 Fixes: 991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()") Reported-and-tested-by: Олег Мороз <oleg.moroz@mcc.vniiem.ru> Reported-by: Sunjin Yang <fan4326@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael@kernel.org> CC: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Daniel Fraga <fragabr@gmail.com> Tested-by: Daniel Fraga <fragabr@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like recent changes in the Wacom driver made the Bamboo ONE crashes.
The tablet behaves as if it was a regular Bamboo device with pen, touch
and pad, but there is no physical pad connected to it.
The weird part is that the pad is still sending events and given that
there is no input node connected to it, we get anull pointer exception.
This is Dell usb dock audio workaround.
It was fixed the master volume keep lower.
[Some background: the patch essentially skips the controls of a couple
of FU volumes. Although the firmware exposes the dB and the value
information via the usb descriptor, changing the values (we set the
min volume as default) screws up the device. Although this has been
fixed in the newer firmware, the devices are shipped with the old
firmware, thus we need the workaround in the driver side. -- tiwai]
Plantronics BT300 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1". This patch adds the USB
ID of the BT300 to quirks.c and avoids those error messages.
Phoenix Audio TMX320 gives the similar error when the sample rate is
asked:
usb 2-1.3: 2:1: cannot get freq at ep 0x85
usb 2-1.3: 1:1: cannot get freq at ep 0x2
....
Add the corresponding USB-device ID (1de7:0014) to
snd_usb_get_sample_rate_quirk() list.
HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires
the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic
working. Also, it suffers from the loopback noise problem, so we
should disable aamix path as well.
On one of the machines we enable, we found that the actual speaker volume
did not always correspond to the volume set in alsamixer. This patch
fixes that problem.
This patch was orginally written by Kailang @ Realtek, I've rebased it
to fit sound git master.
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e516 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Because event_sched_out() checks event->pending_disable _before_
actually disabling the event, it can happen that the event fires after
it checks but before it gets disabled.
This would leave event->pending_disable set and the queued irq_work
will try and process it.
However, if the event trigger was during schedule(), the event might
have been de-scheduled by the time the irq_work runs, and
perf_event_disable_local() will fail.
Fix this by checking event->pending_disable _after_ we call
event->pmu->del(). This depends on the latter being a compiler
barrier, such that the compiler does not lift the load and re-creates
the problem.
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dvyukov@google.com Cc: eranian@google.com Cc: oleg@redhat.com Cc: panand@redhat.com Cc: sasha.levin@oracle.com Cc: vince@deater.net Link: http://lkml.kernel.org/r/20160224174948.040469884@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 128, pid: 383, name: sh
Preemption disabled at:[<ffff800000124c18>] kgdb_cpu_enter+0x158/0x6b8
If we rename an inode A (be it a file or a directory), create a new
inode B with the old name of inode A and under the same parent directory,
fsync inode B and then power fail, at log tree replay time we end up
removing inode A completely. If inode A is a directory then all its files
are gone too.
Example scenarios where this happens:
This is reproducible with the following steps, taken from a couple of
test cases written for fstests which are going to be submitted upstream
soon:
The next time the fs is mounted, log tree replay happens and
the directory "y" does not exist nor do the files "foo" and
"bar" exist anywhere (neither in "y" nor in "x", nor the root
nor anywhere).
The next time the fs is mounted, log tree replay happens and the
file "bar" does not exists anymore. A file with the name "foo"
exists and it matches the second file we created.
Another related problem that does not involve file/data loss is when a
new inode is created with the name of a deleted snapshot and we fsync it:
The next time the fs is mounted the log replay procedure fails because
it attempts to delete the snapshot entry (which has dir item key type
of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry,
resulting in the following error that causes mount to fail:
Fix this by forcing a transaction commit when such cases happen.
This means we check in the commit root of the subvolume tree if there
was any other inode with the same reference when the inode we are
fsync'ing is a new inode (created in the current transaction).
Test cases for fstests, covering all the scenarios given above, were
submitted upstream for fstests:
* fstests: generic test for fsync after renaming directory
https://patchwork.kernel.org/patch/8694281/
* fstests: generic test for fsync after renaming file
https://patchwork.kernel.org/patch/8694301/
* fstests: add btrfs test for fsync after snapshot deletion
https://patchwork.kernel.org/patch/8670671/
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IOMMU drivers that do not support default domains, but make
use of the the group->domain pointer can get that pointer
overwritten with NULL on device add/remove.
Make sure this can't happen by only overwriting the domain
pointer when it is NULL.
Previously, ext4 would fail the mount if the file system had the quota
feature enabled and quota mount options (used for the older quota
setups) were present. This broke xfstests, since xfs silently ignores
the usrquote and grpquota mount options if they are specified. This
commit changes things so that we are consistent with xfs; having the
mount options specified is harmless, so no sense break users by
forbidding them.
With the internal Quota feature, mke2fs creates empty quota inodes and
quota usage tracking is enabled as soon as the file system is mounted.
Since quotacheck is no longer preallocating all of the blocks in the
quota inode that are likely needed to be written to, we are now seeing
a lockdep false positive caused by needing to allocate a quota block
from inside ext4_map_blocks(), while holding i_data_sem for a data
inode. This results in this complaint:
If the lower or upper directory of an overlayfs mount belong to a btrfs
file system and we fsync the file through the overlayfs' merged directory
we ended up accessing an inode that didn't belong to btrfs as if it were
a btrfs inode at btrfs_sync_file() resulting in a crash like the following:
This started happening since commit 4bacc9c9234 (overlayfs: Make f_path
always point to the overlay and f_inode to the underlay) and even though
after this change we could still access the btrfs inode through
struct file->f_mapping->host or struct file->f_inode, we would end up
resulting in more similar issues later on at check_parent_dirs_for_sync()
because the dentry we got (from struct file->f_path.dentry) was from
overlayfs and not from btrfs, that is, we had no way of getting the dentry
that belonged to btrfs (we always got the dentry that belonged to
overlayfs).
The new patch from Miklos Szeredi, titled "vfs: add file_dentry()" and
recently submitted to linux-fsdevel, adds a file_dentry() API that allows
us to get the btrfs dentry from the input file and therefore being able
to fsync when the upper and lower directories belong to btrfs filesystems.
This issue has been reported several times by users in the mailing list
and bugzilla. A test case for xfstests is being submitted as well.
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101951
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109791 Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NFS may be used as lower layer of overlayfs and accessing f_path.dentry can
lead to a crash.
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Acked-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series fixes bugs in nfs and ext4 due to 4bacc9c9234c ("overlayfs:
Make f_path always point to the overlay and f_inode to the underlay").
Regular files opened on overlayfs will result in the file being opened on
the underlying filesystem, while f_path points to the overlayfs
mount/dentry.
This confuses filesystems which get the dentry from struct file and assume
it's theirs.
Add a new helper, file_dentry() [*], to get the filesystem's own dentry
from the file. This checks file->f_path.dentry->d_flags against
DCACHE_OP_REAL, and returns file->f_path.dentry if DCACHE_OP_REAL is not
set (this is the common, non-overlayfs case).
In the uncommon case it will call into overlayfs's ->d_real() to get the
underlying dentry, matching file_inode(file).
The reason we need to check against the inode is that if the file is copied
up while being open, d_real() would return the upper dentry, while the open
file comes from the lower dentry.
[*] If possible, it's better simply to use file_inode() instead.
During revalidate we check whether device capacity has changed before we
decide whether to output disk information or not.
The check for old capacity failed to take into account that we scaled
sdkp->capacity based on the reported logical block size. And therefore
the capacity test would always fail for devices with sectors bigger than
512 bytes and we would print several copies of the same discovery
information.
Avoid scaling sdkp->capacity and instead adjust the value on the fly
when setting the block device capacity and generating fake C/H/S
geometry.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reported-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.
This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
When CONFIG_IIO_TRIGGER is enabled but CONFIG_IIO_BUFFER is
not, we get a build error in the st_magn driver:
drivers/iio/magnetometer/st_magn_core.c:573:23: error: 'ST_MAGN_TRIGGER_SET_STATE' undeclared here (not in a function)
.set_trigger_state = ST_MAGN_TRIGGER_SET_STATE,
^~~~~~~~~~~~~~~~~~~~~~~~~
Apparently, this ST_MAGN_TRIGGER_SET_STATE macro was meant to
be set to NULL when the definition is not available because
st_magn_buffer.c is not compiled, but the alternative definition
was not included in the original patch. This adds it.
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
When unexpected situation happened (e.g. tx/rx irq happened while
DMAC is used), the usbhsf_pkt_handler() was possible to cause NULL
pointer dereference like the followings:
The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.
Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.
When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:
net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.
Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.
The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 98b6218388e3 ("mac80211/cfg80211: add station events") Fixes: 6f7a8d26e266 ("mac80211: send statistics with delete station event") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Fixes: 7bedd0cfad4e1 ("mac80211: use rhashtable for station table") Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spec says: after writing 0 to device_status, the driver MUST wait
for a read of device_status to return 0 before reinitializing the
device.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of 5a60e87603c4c533492c515b7f62578189b03c9c, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Suggested-by: Vlastimil Babka <vbabka@suse.cz> Suggested-by: Neil Brown <neilb@suse.com> Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove the usage of removed irq_to_gpio() function. On pre-DB1200
boards, pass the actual carddetect GPIO number instead of the IRQ,
because we need the gpio to actually test card status (inserted or
not) and can get the irq number with gpio_to_irq() instead.
Tested on DB1300 and DB1500, this patch fixes PCMCIA on the DB1500,
which used irq_to_gpio().
Fixes: 832f5dacfa0b ("MIPS: Remove all the uses of custom gpio.h") Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: linux-pcmcia@lists.infradead.org Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/12747/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity
controllable during streaming") refactored the stream start code and
removed the SRU CTRL0 register write by mistake. Add it back.
Fixes: 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity controllable during streaming") Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The au0828 dev_state is actually a bit mask. It should not be
checking with "==" but, instead, with a logic and. There are some
places where it was doing it wrong.
Fix that by replacing the dev_state set/clear/test with the
bitops.
As reviewed by Shuah:
"Looks good. Tested running bind/unbind au0828 loop for 1000 times.
Didn't see any problems and the v4l2_querycap() problem has been
fixed with this patch.
After the above test, ran bind/unbind snd_usb_audio 1000 times.
Didn't see any problems. Generated media graph and the graph
looks good."
au0828_v4l2_close() check for dev_state == DEV_DISCONNECTED will fail to
detect the device disconnected state correctly, if au0828_v4l2_open() runs
to set the DEV_INITIALIZED bit. A loop test of bind/unbind found this bug
by increasing the likelihood of au0828_v4l2_open() occurring while unbind
is in progress. When au0828_v4l2_close() fails to detect that the device
is in disconnect state, it attempts to power down the device and fails with
the following general protection fault:
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If pinctrl_provide_dummies() is used unconditionally, then the dummy
state will be used even on DT platforms when the "init" state was
intentionally left out. Instead of "default", the dummy "init" state
will then be used during probe. Thus, when probing an I2C controller on
cold boot, communication triggered by bus notifiers broke because the
pins were not initialized.
Do it like OMAP2: use the dummy state only for non-DT platforms.
Fixes: ef0eebc05130 ("drivers/pinctrl: Add the concept of an "init" state") Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copying the content of an MSA vector from user memory may involve TLB
faults & mapping in pages. This will fail when preemption is disabled
due to an inability to acquire mmap_sem from do_page_fault, which meant
such vector loads to unmapped pages would always fail to be emulated.
Fix this by disabling preemption later only around the updating of
vector register state.
This change does however introduce a race between performing the load
into thread context & the thread being preempted, saving its current
live context & clobbering the loaded value. This should be a rare
occureence, so optimise for the fast path by simply repeating the load if
we are preempted.
Additionally if the copy failed then the failure path was taken with
preemption left disabled, leading to the kernel typically encountering
further issues around sleeping whilst atomic. The change to where
preemption is disabled avoids this issue.
Fixes: e4aa1f153add "MIPS: MSA unaligned memory access support" Reported-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: James Cowgill <James.Cowgill@imgtec.com> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12345/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Windows lets applications choose the frequency of the timer tick,
and in Windows 10 the maximum rate was changed from 1024 Hz to
2048 Hz. Unfortunately, because of the way the Windows API
works, most applications who need a higher rate than the default
64 Hz will just do
and pick the maximum rate. This causes very high CPU usage when
playing media or games on Windows 10, even if the guest does not
actually use the CPU very much, because the frequent timer tick
causes halt_poll_ns to kick in.
There is no really good solution, especially because Microsoft
could sooner or later bump the limit to 4096 Hz, but for now
the best we can do is lower a bit the upper limit for
halt_poll_ns. :-(
Reported-by: Jon Panozzo <jonp@lime-technology.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non maskable interrupts (NMI) are preferred to interrupts in current
implementation. If a NMI is pending and NMI is blocked by the result
of nmi_allowed(), pending interrupt is not injected and
enable_irq_window() is not executed, even if interrupts injection is
allowed.
In old kernel (e.g. 2.6.32), schedule() is often called in NMI context.
In this case, interrupts are needed to execute iret that intends end
of NMI. The flag of blocking new NMI is not cleared until the guest
execute the iret, and interrupts are blocked by pending NMI. Due to
this, iret can't be invoked in the guest, and the guest is starved
until block is cleared by some events (e.g. canceling injection).
This patch injects pending interrupts, when it's allowed, even if NMI
is blocked. And, If an interrupts is pending after executing
inject_pending_event(), enable_irq_window() is executed regardless of
NMI pending counter.
Signed-off-by: Yuki Shibuya <shibuya.yk@ncos.nec.co.jp> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The union descriptor must be checked. Its usage was conditional
before the parser was introduced. This is important, because
many RNDIS device, which also use the common parser, have
bogus extra descriptors.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: Vasily Galkin <galkin-vv@yandex.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Reported-and-tested-by: David Webb <djw@noc.ac.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64d513ac31bd ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to
find the output device. In case of an error, inet{,6}_fib_lookup_dev()
returns error pointer and dev_get_by_index() returns NULL. But the function
only checks for NULL and thus can end up calling dev_put on an ERR_PTR.
This patch adds an additional check for err ptr after the NULL check.
After patch:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
RTNETLINK answers: Network is unreachable
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Reported-by: Ji Jianwen <jiji@redhat.com> Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log