When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com> Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: Steven Hardy <shardy@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
next_pidmap() just quietly accepted whatever 'last' pid that was passed
in, which is not all that safe when one of the users is /proc.
Admittedly the proc code should do some sanity checking on the range
(and that will be the next commit), but that doesn't mean that the
helper functions should just do that pidmap pointer arithmetic without
checking the range of its arguments.
So clamp 'last' to PID_MAX_LIMIT. The fact that we then do "last+1"
doesn't really matter, the for-loop does check against the end of the
pidmap array properly (it's only the actual pointer arithmetic overflow
case we need to worry about, and going one bit beyond isn't going to
overflow).
[ Use PID_MAX_LIMIT rather than pid_max as per Eric Biederman ]
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com> Analyzed-by: Robert Święcki <robert@swiecki.net> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
5520e89 ("brk: fix min_brk lower bound computation for COMPAT_BRK")
tried to get the whole logic of brk randomization for legacy
(libc5-based) applications finally right.
It turns out that the way to detect whether brk has actually been
randomized in the end or not introduced by that patch still doesn't work
for those binaries, as reported by Geert:
: /sbin/init from my old m68k ramdisk exists prematurely.
:
: Before the patch:
:
: | brk(0x80005c8e) = 0x80006000
:
: After the patch:
:
: | brk(0x80005c8e) = 0x80005c8e
:
: Old libc5 considers brk() to have failed if the return value is not
: identical to the requested value.
I don't like it, but currently see no better option than a bit flag in
task_struct to catch the CONFIG_COMPAT_BRK && randomize_va_space == 2
case.
Two years later, I've found obvious meaningless code fragment and
restored original intention by following commit.
2010 Jun 04; commit bb21c7ce; vmscan: fix do_try_to_free_pages()
return value when priority==0
But, the logic didn't works when 32bit highmem system goes hibernation
and Minchan slightly changed the algorithm and fixed it .
2010 Sep 22: commit d1908362: vmscan: check all_unreclaimable
in direct reclaim path
But, recently, Andrey Vagin found the new corner case. Look,
struct zone {
..
int all_unreclaimable;
..
unsigned long pages_scanned;
..
}
zone->all_unreclaimable and zone->pages_scanned are neigher atomic
variables nor protected by lock. Therefore zones can become a state of
zone->page_scanned=0 and zone->all_unreclaimable=1. In this case, current
all_unreclaimable() return false even though zone->all_unreclaimabe=1.
This resulted in the kernel hanging up when executing a loop of the form
as described in
http://www.gossamer-threads.com/lists/linux/kernel/1348725#1348725
Is this ignorable minor issue? No. Unfortunately, x86 has very small dma
zone and it become zone->all_unreclamble=1 easily. and if it become
all_unreclaimable=1, it never restore all_unreclaimable=0. Why? if
all_unreclaimable=1, vmscan only try DEF_PRIORITY reclaim and
a-few-lru-pages>>DEF_PRIORITY always makes 0. that mean no page scan at
all!
Eventually, oom-killer never works on such systems. That said, we can't
use zone->pages_scanned for this purpose. This patch restore
all_unreclaimable() use zone->all_unreclaimable as old. and in addition,
to add oom_killer_disabled check to avoid reintroduce the issue of commit d1908362 ("vmscan: check all_unreclaimable in direct reclaim path").
Reported-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Nick Piggin <npiggin@kernel.dk> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scheduler load balancer has specific code to deal with cases of
unbalanced system due to lots of unmovable tasks (for example because of
hard CPU affinity). In those situation, it excludes the busiest CPU that
has pinned tasks for load balance consideration such that it can perform
second 2nd load balance pass on the rest of the system.
This all works as designed if there is only one cgroup in the system.
However, when we have multiple cgroups, this logic has false positives and
triggers multiple load balance passes despite there are actually no pinned
tasks at all.
The reason it has false positives is that the all pinned logic is deep in
the lowest function of can_migrate_task() and is too low level:
load_balance_fair() iterates each task group and calls balance_tasks() to
migrate target load. Along the way, balance_tasks() will also set a
all_pinned variable. Given that task-groups are iterated, this all_pinned
variable is essentially the status of last group in the scanning process.
Task group can have number of reasons that no load being migrated, none
due to cpu affinity. However, this status bit is being propagated back up
to the higher level load_balance(), which incorrectly think that no tasks
were moved. It kick off the all pinned logic and start multiple passes
attempt to move load onto puller CPU.
To fix this, move the all_pinned aggregation up at the iterator level.
This ensures that the status is aggregated over all task-groups, not just
last one in the list.
The new bfin_rtc_alarm_irq_enable function forgot to add a "return 0" to
the end leading to the build warning:
drivers/rtc/rtc-bfin.c: In function 'bfin_rtc_alarm_irq_enable':
drivers/rtc/rtc-bfin.c:253: warning: control reaches end of non-void function
CC: Thomas Gleixner <tglx@linutronix.de> CC: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During RCU walk in path_lookupat and path_openat, the rcu lookup
frequently failed if looking up an absolute path, because when root
directory was looked up, seq number was not properly set in nameidata.
We dropped out of RCU walk in nameidata_drop_rcu due to mismatch in
directory entry's seq number. We reverted to slow path walk that need
to take references.
With the following patch, I saw a 50% increase in an exim mail server
benchmark throughput on a 4-socket Nehalem-EX system.
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for Always Running APIC timer (ARAT) was introduced in
commit db954b5898dd3ef3ef93f4144158ea8f97deb058. This feature
allows us to avoid switching timers from LAPIC to something else
(e.g. HPET) and go into timer broadcasts when entering deep
C-states.
AMD processors don't provide a CPUID bit for that feature but
they also keep APIC timers running in deep C-states (except for
cases when the processor is affected by erratum 400). Therefore
we should set ARAT feature bit on AMD CPUs.
Tested-by: Borislav Petkov <borislav.petkov@amd.com> Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com> Acked-by: Mark Langsdorf <mark.langsdorf@amd.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
LKML-Reference: <1300205624-4813-1-git-send-email-ostr@amd64.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes severe UBIFS bug: UBIFS oopses when we 'fsync()' an
file on R/O-mounter file-system. We (the UBIFS authors) incorrectly
thought that VFS would not propagate 'fsync()' down to the file-system
if it is read-only, but this is not the case.
It is easy to exploit this bug using the following simple perl script:
use strict;
use File::Sync qw(fsync sync);
die "File path is not specified" if not defined $ARGV[0];
my $path = $ARGV[0];
open FILE, "<", "$path" or die "Cannot open $path: $!";
fsync(\*FILE) or die "cannot fsync $path: $!";
close FILE or die "Cannot close $path: $!";
Thanks to Reuben Dowle <Reuben.Dowle@navico.com> for reporting about this
issue.
This is an almost-revert of commit 93b43fa ("oom: give the dying task a
higher priority").
That commit dramatically improved oom killer logic when a fork-bomb
occurs. But I've found that it has nasty corner case. Now cpu cgroup has
strange default RT runtime. It's 0! That said, if a process under cpu
cgroup promote RT scheduling class, the process never run at all.
If an admin inserts a !RT process into a cpu cgroup by setting
rtruntime=0, usually it runs perfectly because a !RT task isn't affected
by the rtruntime knob. But if it promotes an RT task via an explicit
setscheduler() syscall or an OOM, the task can't run at all. In short,
the oom killer doesn't work at all if admins are using cpu cgroup and don't
touch the rtruntime knob.
Eventually, kernel may hang up when oom kill occur. I and the original
author Luis agreed to disable this logic.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Luis Claudio R. Goncalves <lclaudio@uudg.org> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On no-mmu arch, there is a memleak during shmem test. The cause of this
memleak is ramfs_nommu_expand_for_mapping() added page refcount to 2
which makes iput() can't free that pages.
The simple test file is like this:
int main(void)
{
int i;
key_t k = ftok("/etc", 42);
for ( i=0; i<100; ++i) {
int id = shmget(k, 10000, 0644|IPC_CREAT);
if (id == -1) {
printf("shmget error\n");
}
if(shmctl(id, IPC_RMID, NULL ) == -1) {
printf("shm rm error\n");
return -1;
}
}
printf("run ok...\n");
return 0;
}
And the result:
root:/> free
total used free shared buffers
Mem: 60320 17912 42408 0 0
-/+ buffers: 17912 42408
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 19096 41224 0 0
-/+ buffers: 19096 41224
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 20296 40024 0 0
-/+ buffers: 20296 40024
...
After this patch the test result is:(no memleak anymore)
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
Signed-off-by: Bob Liu <lliubbo@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The conventional format for boolean attributes in sysfs is numeric ("0" or
"1" followed by new-line). Any boolean attribute can then be read and
written using a generic function. Using the strings "yes [no]", "[yes]
no" (read), "yes" and "no" (write) will frustrate this.
[akpm@linux-foundation.org: use kstrtoul()]
[akpm@linux-foundation.org: test_bit() doesn't return 1/0, per Neil] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Hugh Dickins <hughd@google.com> Tested-by: David Rientjes <rientjes@google.com> Cc: NeilBrown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. simple_strto*() do not contain overflow checks and crufty,
libc way to indicate failure.
2. strict_strto*() also do not have overflow checks but the name and
comments pretend they do.
3. Both families have only "long long" and "long" variants,
but users want strtou8()
4. Both "simple" and "strict" prefixes are wrong:
Simple doesn't exactly say what's so simple, strict should not exist
because conversion should be strict by default.
The solution is to use "k" prefix and add convertors for more types.
Enter
kstrtoull()
kstrtoll()
kstrtoul()
kstrtol()
kstrtouint()
kstrtoint()
Include runtime testsuite (somewhat incomplete) as well.
strict_strto*() become deprecated, stubbed to kstrto*() and
eventually will be removed altogether.
Use kstrto*() in code today!
Note: on some archs _kstrtoul() and _kstrtol() are left in tree, even if
they'll be unused at runtime. This is temporarily solution,
because I don't want to hardcode list of archs where these
functions aren't needed. Current solution with sizeof() and
__alignof__ at least always works.
The FLAGS_HAS_TIMEOUT flag was not getting set, causing the restart_block to
restart futex_wait() without a timeout after a signal.
Commit b41277dc7a18ee332d in 2.6.38 introduced the regression by accidentally
removing the the FLAGS_HAS_TIMEOUT assignment from futex_wait() during the setup
of the restart block. Restore the originaly behavior.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=32922 Reported-by: Tim Smith <tsmith201104@yahoo.com> Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Kacur <jkacur@redhat.com> Link: http://lkml.kernel.org/r/%3Cdaac0eb3af607f72b9a4d3126b2ba8fb5ed3b883.1302820917.git.dvhart%40linux.intel.com%3E Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the warnings emitted (we fail arch/sparc file
builds with -Werror) were legitimate but harmless, however
one case (n2_pcr_write) was a genuine bug.
Based almost entirely upon a patch by Sam Ravnborg.
Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does. In binutils 2.21 these are treated
as errors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Whenever we enter the IP stack proper from bridge netfilter we
need to ensure that the skb is in a form the IP stack expects
it to be in.
The entry point on NF_FORWARD did not meet the requirements of
the IP stack, therefore leading to potential crashes/panics.
This patch fixes the problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c95b819ad7 (gre: Use needed_headroom)
made gre use needed_headroom instead of hard_header_len
This uncover a bug in vlan code.
We should make sure vlan devices take into account their
real_dev->needed_headroom or we risk a crash in ipgre_header(), because
we dont have enough room to push IP header in skb.
Reported-by: Diddi Oscarsson <diddi@diddi.se> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We return a destination entry without refcount if a socket
policy is found in xfrm_lookup. This triggers a warning on
a negative refcount when freeeing this dst entry. So take
a refcount in this case to fix it.
This refcount was forgotten when xfrm changed to cache bundles
instead of policies for outgoing flows.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the current undo logic, cwnd is moderated after it was restored
to the value prior entering fast-recovery. It was moderated first
in tcp_try_undo_recovery then again in tcp_complete_cwr.
Since the undo indicates recovery was false, these moderations
are not necessary. If the undo is triggered when most of the
outstanding data have been acknowledged, the (restored) cwnd is
falsely pulled down to a small value.
This patch removes these cwnd moderations if cwnd is undone
a) during fast-recovery
b) by receiving DSACKs past fast-recovery
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like DCCP and other similar pieces of code, there are mechanisms
here to try allocating smaller hash tables if the allocation
fails. So pass in __GFP_NOWARN like the others do instead of
emitting a scary message.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Signed-off-by: Dan Siemon <dan@coverfire.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Dave Täht <d@taht.net> Cc: Jonathan Morton <chromatix99@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I was fixing issues with unregisgtering tables under /proc/sys/net/ipv6/neigh
by adding a mount point it appears I missed a critical ordering issue, in the
ipv6 initialization. I had not realized that ipv6_sysctl_register is called
at the very end of the ipv6 initialization and in particular after we call
neigh_sysctl_register from ndisc_init.
"neigh" needs to be initialized in ipv6_static_sysctl_register which is
the first ipv6 table to initialized, and definitely before ndisc_init.
This removes the weirdness of duplicate tables while still providing a
"neigh" mount point which prevents races in sysctl unregistering.
This was initially reported at https://bugzilla.kernel.org/show_bug.cgi?id=31232 Reported-by: sunkan@zappa.cx Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A struct used in the l2tp_eth driver for registering network namespace
ops was incorrectly marked as __net_initdata, leading to oops when
module unloaded.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As specified by errata eTSEC49 of MPC8548 and errata eTSEC12 of MPC83xx,
older revisions of gianfar controllers will be unable to calculate a TCP/UDP
packet checksum for some alignments of the appropriate FCB. This patch checks
for FCB alignment on such controllers and falls back to software checksumming
if the alignment is known to be bad.
Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel J Blueman reported a lockdep splat in trie_firstleaf(), caused by
RTNL being not locked before a call to fib_table_flush()
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipv6_dev_get_saddr() is currently called with an uninitialized
destination address. Although in tests it usually seemed to nevertheless
always fetch the right source address, there seems to be a possible race
condition.
Therefore this commit changes this, first setting the destination
address and only after that fetching the source address.
Reported-by: Jan Beulich <JBeulich@novell.com> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| - once an event is created by sys_perf_event_open, task context
| is created and it stays even if the event is closed, until the
| task is finished ... thats what I see in code and I assume it's
| correct
|
| - when the task opens event, perf_sched_events jump label is
| incremented and following callbacks are started from scheduler
|
| __perf_event_task_sched_in
| __perf_event_task_sched_out
|
| These callback *in/out set/unset cpuctx->task_ctx value to the
| task context.
|
| - close is called on event on CPU 0:
| - the task is scheduled on CPU 0
| - __perf_event_task_sched_in is called
| - cpuctx->task_ctx is set
| - perf_sched_events jump label is decremented and == 0
| - __perf_event_task_sched_out is not called
| - cpuctx->task_ctx on CPU 0 stays set
|
| - exit is called on CPU 1:
| - the task is scheduled on CPU 1
| - perf_event_exit_task is called
| - task_ctx_sched_out unsets cpuctx->task_ctx on CPU 1
| - put_ctx destroys the context
|
| - another call of perf_rotate_context on CPU 0 will use invalid
| task_ctx pointer, and eventualy panic.
|
Cure this the simplest possibly way by partially reverting the
jump_label optimization for the sched_out case.
UBIFS assert failed in ubifs_leb_unmap at 135 (pid 29365)
Pid: 29365, comm: integck Tainted: G I 2.6.37-ubi-2.6+ #34
Call Trace:
[<ffffffffa047c663>] ubifs_lpt_init+0x95e/0x9ee [ubifs]
[<ffffffffa04623a7>] ubifs_remount_fs+0x2c7/0x762 [ubifs]
[<ffffffff810f066e>] do_remount_sb+0xb6/0x101
[<ffffffff81106ff4>] ? do_mount+0x191/0x78e
[<ffffffff811070bb>] do_mount+0x258/0x78e
[<ffffffff810da1e8>] ? alloc_pages_current+0xa2/0xc5
[<ffffffff81107674>] sys_mount+0x83/0xbd
[<ffffffff81009a12>] system_call_fastpath+0x16/0x1b
They happen when we re-mount from R/O mode to R/W mode. While
re-mounting, we write to the media, but we still have the c->ro_mount
flag set. The fix is very simple - just clear the flag before
starting re-mounting R/W.
Commit 53a7706d5ed8 ("mlock: do not hold mmap_sem for extended periods
of time") changed mlock() to care about the exact number of pages that
__get_user_pages() had brought it. Before, it would only care about
errors.
And that doesn't work, because we also handled one page specially in
__mlock_vma_pages_range(), namely the stack guard page. So when that
case was handled, the number of pages that the function returned was off
by one. In particular, it could be zero, and then the caller would end
up not making any progress at all.
Rather than try to fix up that off-by-one error for the mlock case
specially, this just moves the logic to handle the stack guard page
into__get_user_pages() itself, thus making all the counts come out
right automatically.
ia64_mca_cpu_init has a void *data local variable that is assigned
the value from either __get_free_pages() or mca_bootmem(). The problem
is that __get_free_pages returns an unsigned long and mca_bootmem, via
alloc_bootmem(), returns a void *. format_mca_init_stack takes the void *,
and it's also used with __pa(), but that casts it to long anyway.
This results in the following build warning:
arch/ia64/kernel/mca.c:1898: warning: assignment makes pointer from
integer without a cast
Cast the return of __get_free_pages to a void * to avoid
the warning.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
'simple' would have required specifying current frame address
and return address location manually, but that's obviously not
the case (and not necessary) here.
Currently, for N 5800 XM I get:
cdc_phonet: probe of 1-6:1.10 failed with error -22
It's because phonet_header is empty. Extra altsetting looks like
there:
E 05 24 00 01 10 03 24 ab 05 24 06 0a 0b 04 24 fd .$....$..$....$.
E 00 .
I don't see the header used anywhere so just check if the phonet
descriptor is there, not the structure itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Cc: David S. Miller <davem@davemloft.net> Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While testing my patchset to fix asynchronous writes, I hit a bunch
of signature problems when testing with signing on. The problem seems
to be that signature checks on receive can be running at the same
time as a process that is sending, or even that multiple receives can
be checking signatures at the same time, clobbering the same data
structures.
While we're at it, clean up the comments over cifs_calculate_signature
and add a note that the srv_mutex should be held when calling this
function.
This patch seems to fix the problems for me, but I'm not clear on
whether it's the best approach. If it is, then this should probably
go to stable too.
Cc: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 522440ed made cifs set backing_dev_info on the mapping attached
to new inodes. This change caused a fairly significant read performance
regression, as cifs started doing page-sized reads exclusively.
By virtue of the fact that they're allocated as part of cifs_sb_info by
kzalloc, the ra_pages on cifs BDIs get set to 0, which prevents any
readahead. This forces the normal read codepaths to use readpage instead
of readpages causing a four-fold increase in the number of read calls
with the default rsize.
Fix it by setting ra_pages in the BDI to the same value as that in the
default_backing_dev_info.
Reported-and-Tested-by: Till <till2.schaefer@uni-dortmund.de> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cifs_close doesn't check that the filp->private_data is non-NULL before
trying to put it. That can cause an oops in certain error conditions
that can occur on open or lookup before the private_data is set.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, we skip doing the is_path_accessible check in cifs_mount if
there is no prefixpath. I have a report of at least one server however
that allows a TREE_CONNECT to a share that has a DFS referral at its
root. The reporter in this case was using a UNC that had no prefixpath,
so the is_path_accessible check was not triggered and the box later hit
a BUG() because we were chasing a DFS referral on the root dentry for
the mount.
This patch fixes this by removing the check for a zero-length
prefixpath. That should make the is_path_accessible check be done in
this situation and should allow the client to chase the DFS referral at
mount time instead.
Reported-and-Tested-by: Yogesh Sharma <ysharma@cymer.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently only rv515 asics need the workaround
added in f24d86f1a49505cdea56728b853a5d0a3f8e3d11
(drm/radeon/kms: fix resume regression for some r5xx laptops).
Commit 982134ba6261 ("mm: avoid wrapping vm_pgoff in mremap()") fixed
the case of a expanding mapping causing vm_pgoff wrapping when you used
mremap. But there was another case where we expand mappings hiding in
plain sight: the automatic stack expansion.
This fixes that case too.
This one also found by Robert Święcki, using his nasty system call
fuzzer tool. Good job.
Lock stateid's can have access_bmap 0 if they were only partially
initialized (due to a failed lock request); handle that case in
free_generic_stateid.
Reported-by: Mi Jinlong <mijinlong@cn.fujitsu.com> Tested-by: Mi Jinlong <mijinlong@cn.fujitsu.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was noticed by users who performed more than 2^32 lock operations
and hence made this counter overflow (eventually leading to
use-after-free's). Setting rq_client to NULL here means that it won't
later get auth_domain_put() when it should be.
Appears to have been introduced in 2.5.42 by "[PATCH] kNFSd: Move auth
domain lookup into svcauth" which moved most of the rq_client handling
to common svcauth code, but left behind this one line.
Cc: Neil Brown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When writing a contiguous set of blocks, two indirect blocks could be
needed depending on how the blocks are aligned, so we need to increase
the number of credits needed by one.
[ Also fixed a another bug which could further underestimate the
number of journal credits needed by 1; the code was using integer
division instead of DIV_ROUND_UP() -- tytso]
In ext4_register_li_request, we malloc a ext4_li_request and
inserts it into ext4_li_info->li_request_list. In case of any
error later, we free it in the end. But if we have some error
in ext4_run_lazyinit_thread, the whole li_request_list will be
dropped and freed in it. So we will double free this ext4_li_request.
This patch just sets elr to NULL after it is inserted to the list
so that the latter kfree won't double free it.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.
We no longer use release_vccs() so we can delete it.
release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.
Also include the size, vpi, and vci in the debug as is done on
receive.
Use "port" consistently instead of "device" intermittently.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handle the rare case where a directory metadata block is uncompressed and
corrupted, leading to a kernel oops in directory scanning (memcpy).
Normally corruption is detected at the decompression stage and dealt with
then, however, this will not happen if:
- metadata isn't compressed (users can optionally request no metadata
compression), or
- the compressed metadata block was larger than the original, in which
case the uncompressed version was used, or
- the data was corrupt after decompression
This patch fixes this by adding some sanity checks against known maximum
values.
Bugzilla bug 31422 reports occasional "page allocation failure. order:4"
at Squashfs mount time. Fix this by making zlib workspace allocation
use vmalloc rather than kmalloc.
Acer BIOS keeps devices state when system reboot, but reset to default
device states (Wlan on, Bluetooth off, wwan on) if system cold boot.
That means BIOS's initial state is not always real persistence.
So, removed rfkill_init_sw_state because it sets initial state to
persistence then replicate to other new killswitch when rfkill-input
enabled.
After removed it, acer-wmi set initial soft-block state after rfkill
register, and doesn't allow set_block until rfkill initial finished.
Error path in file drivers/media/video/tlg2300/pd-video.c:
1. First mutex_unlock on &pd->lock in line 767 (in function that
called from line 805)
2. Second in line 806
Was: [PATCH] sound/oss/midi_synth: prevent underflow, use of
uninitialized value, and signedness issue
The offset passed to midi_synth_load_patch() can be essentially
arbitrary. If it's greater than the header length, this will result in
a copy_from_user(dst, src, negative_val). While this will just return
-EFAULT on x86, on other architectures this may cause memory corruption.
Additionally, the length field of the sysex_info structure may not be
initialized prior to its use. Finally, a signed comparison may result
in an unintentionally large loop.
On suggestion by Takashi Iwai, version two removes the offset argument
from the load_patch callbacks entirely, which also resolves similar
issues in opl3. Compile tested only.
v3 adjusts comments and hopefully gets copy offsets right.
Static analyzer of clang found a dead store which appears to be a bug in
reading count of items in SEQOF field, only the lower byte of word is
stored. This may lead to corrupted read and communication shutdown.
The bug has been in the module since it's first inclusion into linux
kernel.
[Patrick: the bug is real, but without practical consequence since the
largest amount of sequence-of members we parse is 30.]
Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
struct aunhdr has 4 padding bytes between 'pad' and 'handle' fields on
x86_64. These bytes are not initialized in the variable 'ah' before
sending 'ah' to the network. This leads to 4 bytes kernel stack
infoleak.
This bug was introduced before the git epoch.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Phil Blundell <philb@gnu.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Structures ip6t_replace, compat_ip6t_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second was
introduced in 3bc3fe5e (v2.6.25-rc1); the third is introduced by 6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
'buffer' string is copied from userspace. It is not checked whether it is
zero terminated. This may lead to overflow inside of simple_strtoul().
Changli Gao suggested to copy not more than user supplied 'size' bytes.
It was introduced before the git epoch. Files "ipt_CLUSTERIP/*" are
root writable only by default, however, on some setups permissions might be
relaxed to e.g. network admin user.
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second is
introduced by 6b7d31fc (v2.6.15-rc1); the third is introduced by 6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
commit f3c5c1bfd4308 (make ip_tables reentrant) introduced a race in
handling the stackptr restore, at the end of ipt_do_table()
We should do it before the call to xt_info_rdunlock_bh(), or we allow
cpu preemption and another cpu overwrites stackptr of original one.
A second fix is to change the underflow test to check the origptr value
instead of 0 to detect underflow, or else we allow a jump from different
hooks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first and the third bugs were introduced before the git epoch; the
second was introduced in 2722971c (v2.6.17-rc1). To trigger the bug
one should have CAP_NET_ADMIN.
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com> Signed-off-by: Peter Huewe <huewe.external@infineon.com> Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a hole spans across page boundaries, the next write forces
a read of the block. This could end up reading existing garbage
data from the disk in ocfs2_map_page_blocks. This leads to
non-zero holes. In order to avoid this, mark the writes as new
when the holes span across page boundaries.
Struct ca is copied from userspace. It is not checked whether the "device"
field is NULL terminated. This potentially leads to BUG() inside of
alloc_netdev_mqs() and/or information leak by creating a device with a name
made of contents of kernel stack.
Struct tmp is copied from userspace. It is not checked whether the "name"
field is NULL terminated. This may lead to buffer overflow and passing
contents of kernel stack as a module name to try_then_request_module() and,
consequently, to modprobe commandline. It would be seen by all userspace
processes.
struct sco_conninfo has one padding byte in the end. Local variable
cinfo of type sco_conninfo is copied to userspace with this uninizialized
one byte, leading to old stack contents leak.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log