When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw> Reported-by: Jorrit Tijben <sjorrit@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
If reserve_pmc_hardware() succeeds but reserve_ds_buffers()
fails, then we need to release_pmc_hardware. It won't be done
by the destroy() callback because we return before setting it
in case of error.
Per IEEE 1394 clause 8.4.2.3, a contender for the IRM role shall check
whether the current IRM complies to 1394a-2000 or later. If not force a
compliant node (e.g. itself) to become IRM. This was implemented in the
older ieee1394 driver but not yet in firewire-core.
An older Sony camcorder (Sony DCR-TRV25) which implements 1394-1995 IRM
but neither 1394a-2000 IRM nor BM was now found to cause an
interoperability bug:
- Camcorder becomes root node when plugged in, hence gets IRM role.
- firewire-core successfully contends for BM role, proceeds to perform
gap count optimization and resets the bus.
- Sony camcorder ignores presence of a BM (against the spec, this is
a firmware bug), performs its idea of gap count optimization and
resets the bus.
- Preceding two steps are repeated endlessly, bus never settles,
regular I/O is practically impossible.
http://thread.gmane.org/gmane.linux.kernel.firewire.user/3913
This is an interoperability regression from the old to the new drivers.
Fix it indirectly by adding the 1394a IRM check. The spec suggests
three and a half methods to determine 1394a compliance of a remote IRM;
we choose the method of testing the Config_ROM.Bus_Info.generation
field. This is data that firewire-core should have readily available at
this point, i.e. does not require extra I/O.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (missing 1394a check) Reported-by: H. S. <hs.samix@gmail.com> (issue with Sony DCR-TRV25) Tested-by: H. S. <hs.samix@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Aries Lee <arieslee@jmicron.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 56d1de0a21db28e41741cfa0a66e18bc8d920554, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com Tested-by: weedy2887@gmail.com Tested-by: Rick Farina <sidhayn@gmail.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on the sh_tmu change in 66f49121ffa41a19c59965b31b046d8368fec3c7
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct at least one of the incorrect specs for a national instrument
data acquisition card DAQCard-6024E. This card has only four different
gain settings (+-10V, +-5V, +-0.5V, +-0.05V).
Signed-off-by: Martin Homuth-Rosemann <homuth-rosemann@gmx.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/587546
Symptom: On the reporter's ASUS M2V, using PulseAudio in Ubuntu 10.04 LTS
results in the PA daemon crashing shortly after attempting playback of an
audio file.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, attempt playback of an audio file while PulseAudio is
active.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: D Tangman Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/580749
Symptom: on the original reporter's VIA VT1708-based board, the
PulseAudio daemon dies shortly after the user attempts to play an audio
file.
Test case: boot from Ubuntu 10.04 LTS live cd; attempt to play an audio
file.
Resolution: add SSID for the original reporter's hardware to the
position_fix quirk table, explicitly specifying the LPIB method.
Reported-and-Tested-By: Harald Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/542550
Symptom: On the reporter's iMac, in Ubuntu 10.04 LTS neither playback
nor capture appear audible out-of-the-box.
Test case: Boot from an Ubuntu 10.04 LTS live cd or from an installed
configuration and attempt to play or capture audio.
Resolution: Specify the mb31 quirk for this machine in the codec SSID
table.
Reported-and-Tested-By: f3a97 Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/465942
Symptom: On the reporter's ASUS device, using PulseAudio in Ubuntu 10.04
LTS results in the PA daemon crashing shortly after attempting to select
capture or to configure the audio hardware profile.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's capture volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Irihapeti Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the device we are resuming could be the device containing the
swap device we should ensure that the allocation cannot cause
IO.
On resume, this path is triggered when the running system tries to
continue using its devices. If it cannot then the resume will fail;
to try to avoid this we let it dip into the emergency pools.
The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.
As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.
xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.
Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The low-memory corruption checker triggers during suspend/resume, so we
need to reserve the low 64k. Don't be fooled that the BIOS identifies
itself as "Dell Inc.", it's still Phoenix BIOS.
[ hpa: I think we blacklist almost every BIOS in existence. We should
either change this to a whitelist or just make it unconditional. ]
Signed-off-by: Gabor Gombas <gombasg@digikabel.hu>
LKML-Reference: <201005241913.o4OJDIMM010877@imap1.linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I/O errors can happen due to temporary failures, like multipath
errors or losing network contact with the iSCSI server. Because
of that, the VM will retry readpage on the page.
However, do_generic_file_read does not clear PG_error. This
causes the system to be unable to actually use the data in the
page cache page, even if the subsequent readpage completes
successfully!
The function filemap_fault has had a ClearPageError before
readpage forever. This patch simply adds the same to
do_generic_file_read.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Larry Woodman <lwoodman@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Tridgell reports that aio_read(SIGEV_SIGNAL) can fail if the
notification from the helper thread races with setresuid(), see
http://samba.org/~tridge/junkcode/aio_uid.c
This happens because check_kill_permission() doesn't permit sending a
signal to the task with the different cred->xids. But there is not any
security reason to check ->cred's when the task sends a signal (private or
group-wide) to its sub-thread. Whatever we do, any thread can bypass all
security checks and send SIGKILL to all threads, or it can block a signal
SIG and do kill(gettid(), SIG) to deliver this signal to another
sub-thread. Not to mention that CLONE_THREAD implies CLONE_VM.
Change check_kill_permission() to avoid the credentials check when the
sender and the target are from the same thread group.
Also, move "cred = current_cred()" down to avoid calling get_current()
twice.
Note: David Howells pointed out we could relax this even more, the
CLONE_SIGHAND (without CLONE_THREAD) case probably does not need
these checks too.
Roland said:
: The glibc (libpthread) that does set*id across threads has
: been in use for a while (2.3.4?), probably in distro's using kernels as old
: or older than any active -stable streams. In the race in question, this
: kernel bug is breaking valid POSIX application expectations.
Reported-by: Andrew Tridgell <tridge@samba.org> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Cc: Eric Paris <eparis@parisplace.org> Cc: Jakub Jelinek <jakub@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Roland McGrath <roland@redhat.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
radeon's have a special ability to passthrough writes in their internal
memory space directly to PCI, this ability means that if some of the internal
surfaces like the depth buffer point at 0x0, any writes to these will
go directly to RAM at 0x0 via PCI busmastering.
Now mesa used to always emit clears after emitting state, since the
radeon mesa driver was refactored a year or more ago, it was found it
could generate a clear request without ever sending any setup state to the
card. So the clear would attempt to clear the depth buffer at 0x0, which
would overwrite main memory at this point. fs corruption ensues.
Also once one app did this correctly, it would never get set back to 0
making this messy to reproduce.
The kernel should block this from happening as mesa runs without privs,
though it does require the user be connected to the current running X session.
This patch implements a check to make sure the depth offset has been set
before a depth clear occurs and if it finds one it prints a warning and
ignores the depth clear request. There is also a mesa fix to avoid sending
the badness going into mesa.
This only affects r100/r200 GPUs in user modesetting mode.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vfp_put_double() takes the double value in r0,r1 not r1,r2.
Reported-by: Tarun Kanti DebBarma <tarun.kanti@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bug in mm/init.c when freeing the TCM compile memory,
this was being referred to as a char * which is incorrect: this
will dereference the pointer and feed in the value at the location
instead of the address to it. Change it to a plain char and use
&(char) to reference it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reorganises the sa1111_resume() function in a manner the spinlock
happens after calling the sa1111_wake(). This fixes two bugs:
1) This function called sa1111_wake() which tried to claim the same spinlock
the sa1111_resume() already claimed. This would result in certain deadlock.
Original idea for this part: Russell King <rmk+kernel@arm.linux.org.uk>
2) The function didn't unlock the spinlock in case the chip didn't report
correct ID.
Original idea for this part: Julia Lawall <julia@diku.dk>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When functions incoming parameters are not in input operands list gcc
4.5 does not load the parameters into registers before calling this
function but the inline assembly assumes valid addresses inside this
function. This breaks the code because r0 and r1 are invalid when
execution enters v4wb_copy_user_page ()
Also the constant needs to be used as third input operand so account
for that as well.
Tested on qemu arm.
Signed-off-by: Khem Raj <raj.khem@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instruction faults on pre-ARMv6 CPUs are interpreted as
a 'translation fault', but do_translation_fault doesn't
handle well if user mode trying to run instruction above
TASK_SIZE, and result in the infinite retry of that
instruction.
Signed-off-by: Anfei Zhou <anfei.zhou@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the number of sg entries in the ICM chunk reaches MLX4_ICM_CHUNK_LEN,
we must set chunk to NULL even for coherent mappings so that the next
time through the loop will allocate another chunk. Otherwise we'll
overflow the sg list the next time through the loop. This will lead to
memory corruption if this case is hit.
Shaohua Li reported parallel file copy on tmpfs can lead to OOM killer.
This is regression of caused by commit 9ff473b9a7 ("vmscan: evict
streaming IO first"). Wow, It is 2 years old patch!
Currently, tmpfs file cache is inserted active list at first. This means
that the insertion doesn't only increase numbers of pages in anon LRU, but
it also reduces anon scanning ratio. Therefore, vmscan will get totally
confused. It scans almost only file LRU even though the system has plenty
unused tmpfs pages.
Historically, lru_cache_add_active_anon() was used for two reasons.
1) Intend to priotize shmem page rather than regular file cache.
2) Intend to avoid reclaim priority inversion of used once pages.
But we've lost both motivation because (1) Now we have separate anon and
file LRU list. then, to insert active list doesn't help such priotize.
(2) In past, one pte access bit will cause page activation. then to
insert inactive list with pte access bit mean higher priority than to
insert active list. Its priority inversion may lead to uninteded lru
chun. but it was already solved by commit 645747462 (vmscan: detect
mapped file pages used only once). (Thanks Hannes, you are great!)
Thus, now we can use lru_cache_add_anon() instead.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Reported-by: Shaohua Li <shaohua.li@intel.com> Reviewed-by: Wu Fengguang <fengguang.wu@intel.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe:
the buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Chris Zankel <chris@zankel.net> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bug is an oops when dev_get_drvdata() returned null in
cmos_update_irq_enable(). The call tree looks like this:
rtc_dev_ioctl()
=> rtc_update_irq_enable()
=> cmos_update_irq_enable()
It's caused by a race condition in the module initialization. It is
rtc_device_register() which makes the ioctl operations live so I moved
the call to dev_set_drvdata() before the call to rtc_device_register().
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: David Howells <dhowells@redhat.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joerg Roedel [Tue, 1 Jun 2010 09:41:44 +0000 (11:41 +0200)]
x86/amd-iommu: Fix suspend/resume with IOMMU
This is a suspend resume fix for 2.6.32-stable inclusion. The
problem with this patch is that it is not upstream because the code
changed with 2.6.33 and the function where this bug is in was
removed. So this fix does not make sense anymore for anything later than
2.6.32. The patch was tested by multiple partys and is confirmed to fix
the broken suspend/resume issue with the 2.6.32 kernel.
This patch fixes suspend/resume with AMD IOMMU enabled.
When the user sets the block device to readwrite then the mddev should
follow suit. Otherwise, the BUG_ON in md_write_start() will be set to
trigger.
The reverse direction, setting mddev->ro to match a set readonly
request, can be ignored because the blkdev level readonly flag precludes
the need to have mddev->ro set correctly. Nevermind the fact that
setting mddev->ro to 1 may fail if the array is in use.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync. This has a
very small chance of returning wrong data.
Reported-by: Jordan Russell <jr-list-2010@quo.to> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a very small race window when writing to a
RAID1 such that if a device is marked faulty at exactly the wrong
time, the write-in-progress will not be sent to the device,
but the bitmap (if present) will be updated to say that
the write was sent.
Then if the device turned out to still be usable as was re-added
to the array, the bitmap-based-resync would skip resyncing that
block, possibly leading to corruption. This would only be a problem
if no further writes were issued to that area of the device (i.e.
that bitmap chunk).
Prior to 2.6.32, setting /proc/sys/vm/dirty_writeback_centisecs disabled
periodic dirty writeback from kupdate. This got broken and now causes
excessive sys CPU usage if set to zero, as we'll keep beating on
schedule().
Currently we always call start-cpu irrespective of if the CPU is
stopped or not. Unfortunatley on POWER7, firmware seems to not like
start-cpu being called when a cpu already been started. This was not
the case on POWER6 and earlier.
This patch checks to see if the CPU is stopped or not via an
query-cpu-stopped-state call, and only calls start-cpu on CPUs which
are stopped.
This fixes a bug with kexec on POWER7 on PHYP where only the primary
thread would make it to the second kernel.
Reported-by: Ankita Garg <ankita@linux.vnet.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 0119536c, which added the assembly version of strncmp to
powerpc, mentions that it adds two instructions to the version from
boot/string.S to allow it to handle len=0. Unfortunately, it doesn't
always return 0 when that is the case. The length is passed in r5, but
the return value is passed back in r3. In certain cases, this will
happen to work. Otherwise it will pass back the address of the first
string as the return value.
This patch lifts the len <= 0 handling code from memcpy to handle that
case.
Reported by: Christian_Sellars@symantec.com Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Having hsync both start and end on pixel 1072 ain't gonna work very
well. Matches the X server's list.
Signed-off-by: Adam Jackson <ajax@redhat.com> Tested-By: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Bruce Rogers <brogers@novell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported in <http://bugs.debian.org/552299>, MSI appears to be
broken for this on-board device. We already have a quirk for the
P5N32-SLI Premium; extend it to cover both variants of the board.
The SJA1000 command register is concurrently written in the rx-path to free
the receive buffer _and_ in the tx-path to start the transmission.
The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states:
"Between two commands at least one internal clock cycle is needed in
order to proceed. The internal clock is half of the external oscillator
frequency."
On SMP systems the current implementation leads to a write stall in the
tx-path, which can be solved by adding some general locking and some time
to settle the write_reg() operation for the command register.
Thanks to Klaus Hitschler for the original fix and detailed problem
description.
This patch applies on net-2.6 and (with some offsets) on net-next-2.6 .
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without CONFIG_CPUMASK_OFFSTACK, simply inverting cpu_online_mask leads
to CPUs beyond nr_cpu_ids to be displayed twice and CPUs not even
possible to be displayed as offline.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
if (len > tx->local->hw.wiphy->rts_threshold) {
txrc.rts = rts = true;
}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
len = min_t(int, tx->skb->len + FCS_LEN,
tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit e34e09401ee9888dd662b2fca5d607794a56daf2 incorrectly removed
use of ieee80211_has_protected() from the management frame case and in
practice, made this validation drop all Action frames when MFP is
enabled. This should have only been done for frames with Protected
field set to zero.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm. For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).
This will tell kconfig to provide a warning if no rate control algorithms
have been selected. That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The length of the scatter gather list a driver can enqueue is limited by
the bus' sg_tablesize to 62 entries. Each entry will be described by at
least one transfer request block (TRB). If the entry's buffer crosses a
64KB boundary, then that entry will have to be described by two or more
TRBs. So even if the USB device driver respects sg_tablesize, the whole
scatter list may take more than 62 TRBs to describe, and won't fit on
the ring.
Don't assume that an empty ring means there is enough room on the
transfer ring. The old code would unconditionally queue this too-large
transfer, and over write the beginning of the transfer. This would mean
the cycle bit was unchanged in those overwritten transfers, causing the
hardware to think it didn't own the TRBs, and the host would seem to
hang.
Now drivers may see submit_urb() fail with -ENOMEM if the transfers are
too big to fit on the ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the USB core installs a new interface, it unconditionally clears the
halts on all the endpoints on the new interface. Usually the xHCI host
needs to know when an endpoint is reset, so it can change its internal
endpoint state. In this case, it doesn't care, because the endpoints were
never halted in the first place.
To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks
at xhci_virt_ep->stopped_td to determine if the endpoint was actually
halted. However, the functions that handle the stall never set that
variable to NULL after it dealt with the stall. So if an endpoint stalled
and a Reset Endpoint command completed, and then the class driver tried to
install a new alternate setting, the xHCI driver would access the old
xhci_virt_ep->stopped_td pointer. A similar problem occurs if the
endpoint has been stopped to cancel a transfer.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a bug fix for PHCD (phy clock disable) low power feature:
After PHCD is set, any write to PORTSC register is illegal, so when
resume ports, clear PHCD bit first.
Signed-off-by: Alek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These Appotech controllers are found in Picture Frames, they provide a
(buggy) emulation of a cdrom drive which contains the windows software
Uploading of pictures happens over the corresponding /dev/sg device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The max packet length bit mask used for isochronous endpoints
should be 0x7FF instead of 0x8FF. 0x8FF will actually clear
higher-order bits in the max packet length field.
This patch adds support for an olivetti olicard100 HЅDPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Signed-off-by: Nils Radtke <lkml@Think-Future.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591 Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This change adds in the USB product ID for the Gyration
GYR4101US USB media center remote control. This remote
is similar enough to the other two devices that this driver
can be used without any other changes to get full support
for the remote.
The 046d:08da usb id shouldn't be associated with the stv06xx driver as they're
not compatible with each other.
This fixes a bug where Quickcam Messenger cams fail to use its proper driver
(gspca-zc3xx), rendering the camera inoperable.
BugLink: https://launchpad.net/bugs/551949
Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/586347
Symptom: On the Sony VPCS11V9E, using GStreamer-based applications with
PulseAudio in Ubuntu 10.04 LTS results in stuttering audio. It appears
to worsen with increased I/O.
Test case: use Rhythmbox under increased I/O pressure. This symptom is
reproducible in the current daily stable alsa-driver snapshots (at least
up until 21 May 2010; later snapshots fail to build from source due to
missing preprocessor directives when compiled against 2.6.32).
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Lauri Kainulainen <lauri@sokkelo.net> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/583983
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile).
Resolution: add SSID for Acer Aspire 5110 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
Reported-and-Tested-By: Leo Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/549560
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile)
Resolution: add SSID for Toshiba A100-259 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
This patch also trivially sorts the quirk table in ascending order by
subsystem vendor.
Reported-and-Tested-by: <davide.molteni@gmail.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/576160
Symptom: Currently (2.6.32.12) the Dell M1730 uses the 3stack model
quirk. Unfortunately this means that capture is not functional out-
of-the-box despite ensuring that capture settings are unmuted and
raised fully.
Test case: boot from Ubuntu 10.04 LTS live cd; capture does not
work.
Resolution: Correct the model quirk for Dell M1730 to rely on the
BIOS configuration.
This patch also trivially sorts the quirk into the correct section
based on the comments.
Currently, we can hit a nasty case with optimistic
spinning on mutexes:
CPU A tries to take a mutex, while holding the BKL
CPU B tried to take the BLK while holding the mutex
This looks like a AB-BA scenario but in practice, is
allowed and happens due to the auto-release on
schedule() nature of the BKL.
In that case, the optimistic spinning code can get us
into a situation where instead of going to sleep, A
will spin waiting for B who is spinning waiting for
A, and the only way out of that loop is the
need_resched() test in mutex_spin_on_owner().
This patch fixes it by completely disabling spinning
if we own the BKL. This adds one more detail to the
extensive list of reasons why it's a bad idea for
kernel code to be holding the BKL.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <20100519054636.GC12389@ozlabs.org>
[ added an unlikely() attribute to the branch ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
page_mapping() check this via VM_BUG_ON(PageSlab(page)) so we bug here
with the according debuging turned on.
Future TODO: replace this with a flush_dcache_page_for_pio() API
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are ATAPI devices which raise AN when hit by commands issued by
open(). This leads to infinite loop of AN -> MEDIA_CHANGE uevent ->
udev open() to check media -> AN.
Both ACS and SerialATA standards don't define in which case ATAPI
devices are supposed to raise or not raise AN. They both list media
insertion event as a possible use case for ATAPI ANs but there is no
clear description of what constitutes such events. As such, it seems
a bit too naive to export ANs directly to userland as MEDIA_CHANGE
events without further verification (which should behave similarly to
windows as it apparently is the only thing that some hardware vendors
are testing against).
This patch adds libata.atapi_an module parameter and disables ATAPI AN
by default for now.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Nick Bowler <nbowler@elliptictech.com> Cc: David Zeuthen <david@fubar.dk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
once anon_inode_getfd() is called, you can't expect *anything* about
struct file that descriptor points to - another thread might be doing
whatever it likes with descriptor table at that point.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In http://bugzilla.novell.com/show_bug.cgi?id=597299, the vt6655 driver
generates a kernel BUG on a NULL pointer dereference at NULL. This problem
has been traced to a failure in the wpa_set_wpadev() routine. As the vt6656
driver does not call this routine, the vt6655 code is similarly set to skip
the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Richard Meek <osl2008@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SH SOHARD ARCNET cards are implemented using generic PLX Technology
PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified,
causing the driver to attach to any such bridge and likely crash the
system by attempting to initialize an unrelated device.
Fix by specifying subvendor and subdevice according to the values found
in the PCI-ID Repository at http://pci-ids.ucw.cz/ .
Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /proc/fs/nfsd/versions file calls nfsd_vers() to check whether
the particular nfsd version is present/available. The problem is
that once I turn off e.g. NFSD-V4 this call returns -1 which is
true from the callers POV which is wrong.
The proposal is to report false in that case.
The bug has existed since 6658d3a7bbfd1768 "[PATCH] knfsd: remove
nfsd_versbits as intermediate storage for desired versions".
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>