The current configuration selects an incorrect NAND ECC layout,
which causes u-boot to write HW ECC data incorrectly.
This patch selects the right layout.
SRICHARAN R [Tue, 12 Jun 2012 19:53:33 +0000 (19:53 +0000)]
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
Currently on OMAP4/5 platforms, many kernel drivers are dependent
upon the bootloaders for mux, dpll and clock configurations.
This should not be the case and bootloaders should set only the
minimum required for the uboot functionality and kernel boot.
Note that this is going to break the kernel drivers. But this
is the only way to get things fixed in the kernel.
SRICHARAN R [Tue, 12 Jun 2012 19:53:32 +0000 (19:53 +0000)]
ARM: OMAP4/5: Move USB pads to essential list.
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.
SRICHARAN R [Tue, 12 Jun 2012 19:53:31 +0000 (19:53 +0000)]
ARM: OMAP4/5: Move USB clocks to essential group.
USB clocks will be required for fastboot, tftp
related functionalities. Move these clocks to
essential group inorder to have the functionality
working when non-essential clocks are not enabled.
SRICHARAN R [Tue, 12 Jun 2012 19:53:30 +0000 (19:53 +0000)]
ARM: OMAP4/5: Move gpmc clocks to essential group.
GPMC clocks are currently getting enabled as a part
non-essential clocks. This will be required during
NOR boot. Move this to essential group to keep the
functionality, when non-essential clocks are not
enabled.
SRICHARAN R [Mon, 4 Jun 2012 03:40:23 +0000 (03:40 +0000)]
ARM: OMAP4+: Move external phy initialisations to arch specific place.
The external phy is present in the case OMAP5 soc is currently
configured in emif-common.c. This results in having dummy structures
for those Socs which do not have a external phy. So by having a weak
function in emif-common and overriding it in OMAP5, avoids the use
of dummy structures.
da850/omap-l138: Enable auto negotiation in RMII mode
On DA850/OMAP-L138 it was observed that in RMII mode,
auto negotiation was not performed. This patch enables
auto negotiation in RMII mode. Without this patch, EMAC
initialization takes more time and sometimes tftp fails
in RMII mode.
Steve Sakoman [Wed, 30 May 2012 07:38:07 +0000 (07:38 +0000)]
omap: emif: deal with rams that return duplicate mr data on all byte lanes
Some rams (Micron for example) return duplicate mr data on all byte lanes.
Users of the get_mr function currently don't deal with this duplicated
data gracefully. This patch detects the duplicated data and returns only
the expected 8 bit mr data.
Lokesh Vutla [Tue, 29 May 2012 19:26:43 +0000 (19:26 +0000)]
OMAP4+: Force DDR in self-refresh after warm reset
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Lokesh Vutla [Tue, 29 May 2012 19:26:42 +0000 (19:26 +0000)]
OMAP4+: Handle sdram init after warm reset
EMIF and DDR device state are preserved in warmreset. Redoing the full
initialisation would cause unexpected behaviour. Do only partial
initialisation to account for frequency change.
arm: bugfix: Move vector table before jumping relocated code
Interrupts and exceptions doesn't work in relocated code.
It badly use IRQ_STACK_START_IN in rom area as interrupt stack.
It is because the vecotr table is not moved to ram area.
This patch moves vector table before jumping relocated code.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Tested-by: Tom Rini <trini@ti.com>
arm/km: use spi claim bus to switch between SPI and NAND
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.
Simon Guinot [Tue, 5 Jun 2012 13:16:00 +0000 (13:16 +0000)]
ARM: don't probe PHY address for LaCie boards
The command miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr) always
returns 8 for the PHY address. It is the reset value for the PHY
Address Register. Obviously, this default value could be incorrect.
Moreover, as the PHY address is well known, there is no need to
auto-detect it.
Now, the PHY address must given as a parameter to the PHY initialization
function. Additionally this patch also fixes some aesthetic issues.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Michael Walle [Tue, 5 Jun 2012 11:33:15 +0000 (11:33 +0000)]
net: use common rand()/srand() functions
Replace rand() with the functions from lib/. The link-local network code
stores its own seed, derived from the MAC address. Thus making it
independent from calls to srand() in other modules.
Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Luka Perkov [Sun, 27 May 2012 11:44:51 +0000 (11:44 +0000)]
kwboot: boot kirkwood SoCs over a serial link
The kwboot program boots boards based on Marvell's Kirkwood platform
via Xmodem over their integrated UART.
Signed-off-by: Daniel Stodden <daniel.stodden@googlemail.com> Acked-by: Luka Perkov <uboot@lukaperkov.net> Tested-By: Holger Brunck <holger.brunck@keymile.com> Tested-By: David Purdy <david.c.purdy@gmail.com> Tested-by: Simon Guinot <simon.guinot@sequanux.org>
These two function nows ensure that the MPP is configured correctly for
the SPI controller before any SPI access, and restore the initial
configuration when the access is over.
Since the used pins for the SPI controller can differ (2 possibilities
for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP.
kirkwood: add save functionality kirkwood_mpp_conf function
If a second non NULL argument is given to the kirkwood_mpp_conf
function, it will be used to store the current configuration of the MPP
registers. mpp_save must be a preallocated table of the same size as
mpp_list and it must be zero terminated as well.
A later call to kirkwood_mpp_conf function with this saved list as first
(mpp_conf) argment will set the configuration back.
This config option sounds like the it is responsible for the
update of the environment, but it is the u-boot update handling.
Therefore we adapt it to a more apropriate naming.
Holger Brunck [Fri, 25 May 2012 01:57:13 +0000 (01:57 +0000)]
arm/km: add board type to boards.cfg
Some other kirkwood boards from keymile will follow. They will have some
small differences, but we want to use the km_kirkwood.h for all to
distinguish them. This patch a preparation for this.
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00042000
fs 0x00252000
u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.
Now, the layout is:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00084000
fs 0x00294000
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Thu, 28 Jun 2012 02:50:37 +0000 (02:50 +0000)]
ehci-atmel: fix compiler warning
Commit 7a101e946cba55e32d3d1265e30456c810046da3 introduced following warning:
---8<---
ehci-atmel.c: In function 'ehci_hcd_init':
ehci-atmel.c:49:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
ehci-atmel.c: In function 'ehci_hcd_stop':
ehci-atmel.c:79:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
--->8---
This patch fixes it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Bo Shen <voice.shen@atmel.com>
cc: Marek Vasut <marex@denx.de>
Michael Langer [Thu, 14 Jun 2012 03:44:33 +0000 (03:44 +0000)]
i.MX6 USDHC: Use the ESDHC clock
The commit "i.mx: fsl_esdhc: add the i.mx6q support" (4692708d) introduces
support for the i.MX6Q MMC host controller USDHC.
MXC_IPG_PERCLK sets the clock to 66MHz. This seems to be the default clock
of the ESDHC IP found in < i.MX6 silicon. However, the default clock for the USDHC
IP found in i.MX6 is 200MHz (MXC_ESDHC_CLK). This difference will cause a 3 times
higher clock on SD_CLK than expected (see fsl_esdh.c -> set_sysctl()).
Signed-off-by: Michael Langer <michael.langer@de.bosch.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <r64343@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
Marek Vasut [Tue, 29 May 2012 19:43:13 +0000 (19:43 +0000)]
i.MX28: Add function to adjust memory parameters
This function can be overridden at run-time and allows implementors
of new boards based on the i.MX28 chip to fine-tune the memory params.
It is possible to write into the dram_vals array because when the SPL
runs, it is located SRAM. Therefore the location is writable. There is
no possibility of these data to be read-only.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Sat, 2 Jun 2012 21:53:30 +0000 (21:53 +0000)]
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Fabio Estevam [Sat, 2 Jun 2012 21:53:29 +0000 (21:53 +0000)]
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Sat, 2 Jun 2012 21:53:28 +0000 (21:53 +0000)]
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Sat, 2 Jun 2012 21:53:27 +0000 (21:53 +0000)]
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Fabio Estevam [Sat, 2 Jun 2012 21:53:26 +0000 (21:53 +0000)]
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Otavio Salvador [Tue, 15 May 2012 10:59:30 +0000 (10:59 +0000)]
m28evk: drop duplicated definition of CONFIG_OF_LIBFDT
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Marek Vasut <marex@denx.de>
Donghwa Lee [Wed, 25 Apr 2012 13:29:39 +0000 (13:29 +0000)]
TRATS: initialize panel_info data structure in board file
panel_info data structure is gloable variable, so, I have initialized it
in board file. If it is initialized in init_panel_info() like existing,
it can't be used in drv_lcd_init() in common/lcd.c because
init_panel_info() is called after drv_lcd_init().
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nikita Kiryanov [Thu, 24 May 2012 04:01:23 +0000 (04:01 +0000)]
cm-t35: fix legacy board revision representation
Legacy eeprom layout represents the revision number syntactically
(i.e. revision 1.00 is written as 0x100). This is inconsistent with
the representation in newer layouts, where it is defined semantically
(i.e. 0x64).
This patch fixes the issue by replacing the syntactic representation
with the semantic one.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Thu, 24 May 2012 04:01:21 +0000 (04:01 +0000)]
cm-t35: reduce the environment size
Reduce the environment size (128KB => 16KB) to improve the environment
operations time (e.g. reading, ecc calculation).
Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
SRICHARAN R [Thu, 24 May 2012 00:30:25 +0000 (00:30 +0000)]
ARM: OMAP4: Correct the lpddr2 io settings register value.
To meet certain timing requirements on the lpddr2 cmd and data phy
interfaces ,lpddr iopads have to be configured as differential buffers
and a Vref has to be internally generated and provided to these buffers.
Lokesh Vutla [Tue, 22 May 2012 00:03:25 +0000 (00:03 +0000)]
OMAP5: EMIF: Add support for DDR3 device
In OMAP5432 EMIF controlller supports DDR3 device.
This patch adds support for ddr3 device intialization and configuration.
Initialization sequence is done as specified in JEDEC specs.
This also adds support for ddr3 leveling.
projects / karo-tx-uboot.git / log