When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On laptops with core i5/i7, there were reports that after resume
graphics workloads were performing poorly on a specific AP, while
the other cpu's were ok. This was observed on a 32bit kernel
specifically.
Debug showed that the PAT init was not happening on that AP
during resume and hence it contributing to the poor workload
performance on that cpu.
On this system, resume flow looked like this:
1. BP starts the resume sequence and we reinit BP's MTRR's/PAT
early on using mtrr_bp_restore()
2. Resume sequence brings all AP's online
3. Resume sequence now kicks off the MTRR reinit on all the AP's.
4. For some reason, between point 2 and 3, we moved from BP
to one of the AP's. My guess is that printk() during resume
sequence is contributing to this. We don't see similar
behavior with the 64bit kernel but there is no guarantee that
at this point the remaining resume sequence (after AP's bringup)
has to happen on BP.
5. set_mtrr() was assuming that we are still on BP and skipped the
MTRR/PAT init on that cpu (because of 1 above)
6. But we were on an AP and this led to not reprogramming PAT
on this cpu leading to bad performance.
Fix this by doing unconditional mtrr_if->set_all() in set_mtrr()
during MTRR/PAT init. This might be unnecessary if we are still
running on BP. But it is of no harm and will guarantee that after
resume, all the cpu's will be in sync with respect to the
MTRR/PAT registers.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1301438292-28370-1-git-send-email-eric@anholt.net> Signed-off-by: Eric Anholt <eric@anholt.net> Tested-by: Keith Packard <keithp@keithp.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
root_item->flags and root_item->byte_limit are not initialized when
a subvolume is created. This bug is not revealed until we added
readonly snapshot support - now you mount a btrfs filesystem and you
may find the subvolumes in it are readonly.
To work around this problem, we steal a bit from root_item->inode_item->flags,
and use it to indicate if those fields have been properly initialized.
When we read a tree root from disk, we check if the bit is set, and if
not we'll set the flag and initialize the two fields of the root item.
Reported-by: Andreas Philipp <philipp.andreas@gmail.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Tested-by: Andreas Philipp <philipp.andreas@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When parsing the FAC_NATIONAL_DIGIS facilities field, it's possible for
a remote host to provide more digipeaters than expected, resulting in
heap corruption. Check against ROSE_MAX_DIGIS to prevent overflows, and
abort facilities parsing on failure.
Additionally, when parsing the FAC_CCITT_DEST_NSAP and
FAC_CCITT_SRC_NSAP facilities fields, a remote host can provide a length
of less than 10, resulting in an underflow in a memcpy size, causing a
kernel panic due to massive heap corruption. A length of greater than
20 results in a stack overflow of the callsign array. Abort facilities
parsing on these invalid length values.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From the result of a function test of mmap, mmap write to shared pages
turned out to be broken for hole blocks. It doesn't write out filled
blocks and the data will be lost after umount. This is due to a bug
that the target file is not queued for log writer when filling hole
blocks.
Also, nilfs_page_mkwrite function exits normal code path even after
successfully filled hole blocks due to a change of block_page_mkwrite
function; just after nilfs was merged into the mainline,
block_page_mkwrite() started to return VM_FAULT_LOCKED instead of zero
by the patch "mm: close page_mkwrite races" (commit: b827e496c893de0c). The current nilfs_page_mkwrite() is not handling
this value properly.
This corrects nilfs_page_mkwrite() and will resolve the data loss
problem in mmap write.
[This should be applied to every kernel since 2.6.30 but a fix is
needed for 2.6.37 and prior kernels]
Invalid nicknames containing only spaces will result in an underflow in
a memcpy size calculation, subsequently destroying the heap and
panicking.
v2 also catches the case where the provided nickname is longer than the
buffer size, which can result in controllable heap corruption.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Length fields provided by a peer for names and attributes may be longer
than the destination array sizes. Validate lengths to prevent stack
buffer overflows.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FSGEOMETRY_V1 ioctl (and its compat equivalent) calls out to
xfs_fs_geometry() with a version number of 3. This code path does not
fill in the logsunit member of the passed xfs_fsop_geom_t, leading to
the leaking of four bytes of uninitialized stack data to potentially
unprivileged callers.
v2 switches to memset() to avoid future issues if structure members
change, on suggestion of Dave Chinner.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Reviewed-by: Eugene Teo <eugeneteo@kernel.org> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit da48524eb206 ("Prevent rt_sigqueueinfo and rt_tgsigqueueinfo
from spoofing the signal code") made the check on si_code too strict.
There are several legitimate places where glibc wants to queue a
negative si_code different from SI_QUEUE:
- This was first noticed with glibc's aio implementation, which wants
to queue a signal with si_code SI_ASYNCIO; the current kernel
causes glibc's tst-aio4 test to fail because rt_sigqueueinfo()
fails with EPERM.
- Further examination of the glibc source shows that getaddrinfo_a()
wants to use SI_ASYNCNL (which the kernel does not even define).
The timer_create() fallback code wants to queue signals with SI_TIMER.
As suggested by Oleg Nesterov <oleg@redhat.com>, loosen the check to
forbid only the problematic SI_TKILL case.
Reported-by: Klaus Dittrich <kladit@arcor.de> Acked-by: Julien Tinnes <jln@google.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Locking is required when tweaking bits located in a shared page, use the
sync_ version of bitops. Without this change vmbus_on_event() will miss
events and as a result, vmbus_isr() will not schedule the receive tasklet.
[Backported to 2.6.32 stable kernel by Haiyang Zhang <haiyangz@microsoft.com>]
For isochronous packets the actual_length is the sum of the actual
length of each of the packets, however between the packets might be
padding, so it is not sufficient to just send the first actual_length
bytes of the buffer. To fix this and simultanesouly optimize the
bandwidth the content of the isochronous packets are send without the
padding, the padding is restored on the receiving end.
The number_of_packets was not transmitted for RET_SUBMIT packets. The
linux client used the stored number_of_packet from the submitted
request. The windows userland client does not do this however and needs
to know the number_of_packets to determine the size of the transmission.
When doing a usb port reset do a queued reset instead to prevent a
deadlock: the reset will cause the driver to unbind, causing the
usb_driver_lock_for_reset to stall.
The pointer '(*auth_tok_key)' is set to NULL in case request_key()
fails, in order to prevent its use by functions calling
ecryptfs_keyring_auth_tok_for_sig().
During device discovery, scsi mid layer sends INQUIRY command to LUN
0. If the LUN 0 is not mapped to host, it creates a temporary
scsi_device with LUN id 0 and sends REPORT_LUNS command to it. After
the REPORT_LUNS succeeds, it walks through the LUN table and adds each
LUN found to sysfs. At the end of REPORT_LUNS lun table scan, it will
delete the temporary scsi_device of LUN 0.
When scsi devices are added to sysfs, it calls add_dev function of all
the registered class interfaces. If ses driver has been registered,
ses_intf_add() of ses module will be called. This function calls
scsi_device_enclosure() to check the inquiry data for EncServ
bit. Since inquiry was not allocated for temporary LUN 0 scsi_device,
it will cause NULL pointer exception.
To fix the problem, sdev->inquiry is checked for NULL before reading it.
enclosure page 7 gives us the "pretty" names of the enclosure slots.
Without a page 7, we can still use the enclosure code as long as we
make up numeric names for the slots. Unfortunately, the current code
fails to add any devices because the check for page 10 is in the wrong
place if we have no page 7. Fix it so that devices show up even if
the enclosure has no page 7.
Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used to determine the inactivity time. When in AP mode,
hostapd uses it for kicking out inactive clients after a while. Without this
patch, hostapd immediately deauthenticates a new client if it checks the
inactivity time before the client sends its first data frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
User-controllable indexes for voice and channel values may cause reading
and writing beyond the bounds of their respective arrays, leading to
potentially exploitable memory corruption. Validate these indexes.
Under certain workloads a command may seem to get lost. IOW, the Smart Array
thinks all commands have been completed but we still have commands in our
completion queue. This may lead to system instability, filesystems going
read-only, or even panics depending on the affected filesystem. We add an
extra read to force the write to complete.
Testing shows this extra read avoids the problem.
Signed-off-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rmmod myri10ge crash at free_netdev() -> netif_napi_del(), because napi
structures are already deallocated. To fix call netif_napi_del() before
kfree() at myri10ge_free_slices().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The maximum kilobytes of locked memory that an unprivileged user
can reserve is of 512 kB = 128 pages by default, scaled to the
number of onlined CPUs, which fits well with the tools that use
128 data pages by default.
However tools actually use 129 pages, because they need one more
for the user control page. Thus the default mlock threshold is
not sufficient for the default tools needs and we always end up
to evaluate the constant mlock rlimit policy, which doesn't have
this scaling with the number of online CPUs.
Hence, on systems that have more than 16 CPUs, we overlap the
rlimit threshold and fail to mmap:
$ perf record ls
Error: failed to mmap with 1 (Operation not permitted)
Just increase the max unprivileged mlock threshold by one page
so that it supports well perf tools even after 16 CPUs.
Reported-by: Han Pingtian <phan@redhat.com> Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <1300904979-5508-1-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a race between snd_card_file_remove() and
snd_card_disconnect(). When the card is added to shutdown_files list
in snd_card_disconnect(), but it's freed in snd_card_file_remove() at
the same time, the shutdown_files list gets corrupted. The list member
must be freed in snd_card_file_remove() as well.
The commit 5a8cfb4e8ae317d283f84122ed20faa069c5e0c4
ALSA: hda - Use ALC_INIT_DEFAULT for really default initialization
changed to use the default initialization method for ALC889, but
this caused a regression on SPDIF output on some machines.
This seems due to the COEF setup included in the default init procedure.
For making SPDIF working again, the COEF-setup has to be avoided for
the id 0889.
The dcdbas driver can do an I/O write to cause a SMI to occur. The SMI handler
looks at certain registers and memory locations, so the SMI needs to happen
immediately. On some systems I/O writes are posted, though, causing the SMI to
happen well after the "outb" occurred, which causes random failures. Following
the "outb" with an "inb" forces the write to go through even if it is posted.
Signed-off-by: Stuart Hayes <stuart_hayes@yahoo.com> Acked-by: Doug Warzecha <douglas_warzecha@dell.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to track down some NFS problems with BTRFS, I kept noticing I was
getting -EACCESS for no apparent reason. Eric Paris and printk() helped me
figure out that it was SELinux that was giving me grief, with the following
denial
Turns out this is because in d_obtain_alias if we can't find an alias we create
one and do all the normal instantiation stuff, but we don't do the
security_d_instantiate.
Usually we are protected from getting a hashed dentry that hasn't yet run
security_d_instantiate() by the parent's i_mutex, but obviously this isn't an
option there, so in order to deal with the case that a second thread comes in
and finds our new dentry before we get to run security_d_instantiate(), we go
ahead and call it if we find a dentry already. Eric assures me that this is ok
as the code checks to see if the dentry has been initialized already so calling
security_d_instantiate() against the same dentry multiple times is ok. With
this patch I'm no longer getting errant -EACCESS values.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we call xs_close(), we're in one of two situations:
- Autoclose, which means we don't expect to resend a request
- bind+connect failed, which probably means the port is in use
Now cleanup_highmap actually is in two steps: one is early in head64.c
and only clears above _end; a second one is in init_memory_mapping() and
tries to clean from _brk_end to _end.
It should check if those boundaries are PMD_SIZE aligned but currently
does not.
Also init_memory_mapping() is called several times for numa or memory
hotplug, so we really should not handle initial kernel mappings there.
This patch moves cleanup_highmap() down after _brk_end is settled so
we can do everything in one step.
Also we honor max_pfn_mapped in the implementation of cleanup_highmap.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
LKML-Reference: <alpine.DEB.2.00.1103171739050.3382@kaball-desktop> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A virtualized display device is usually viewed with the vncviewer
application, either by 'xm vnc domU' or with vncviewer localhost:port.
vncviewer and the RFB protocol provides absolute coordinates to the
virtual display. These coordinates are either passed through to a PV
guest or converted to relative coordinates for a HVM guest.
A PV guest receives these coordinates and passes them to the kernels
evdev driver. There it can be picked up by applications such as the
xorg-input drivers. Using absolute coordinates avoids issues such as
guest mouse pointer not tracking host mouse pointer due to wrong mouse
acceleration settings in the guests X display.
Advertise either absolute or relative coordinates to the input system
and the evdev driver, depending on what dom0 provides. The xorg-input
driver prefers relative coordinates even if a devices provides both.
Fix potential null-pointer exception on disconnect introduced by commit 11ea859d64b69a747d6b060b9ed1520eab1161fe (USB: additional power savings
for cdc-acm devices that support remote wakeup).
Only access acm->dev after making sure it is non-null in control urb
completion handler.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent read urbs from being resubmitted from tasklet after port close.
The receive tasklet was not disabled on port close, which could lead to
corruption of receive lists on consecutive port open. In particular,
read urbs could be re-submitted before port open, added to free list in
open, and then added a second time to the free list in the completion
handler.
My testprog do a lot of bitbang - after hours i got following warning and my machine lockups:
WARNING: at /build/buildd/linux-2.6.38/lib/kref.c:34
After debugging uss720 driver i discovered that the completion callback was called before
usb_submit_urb returns. The callback frees the request structure that is krefed on return by
usb_submit_urb.
Signed-off-by: Peter Holik <peter@holik.at> Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.
There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH. Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD. Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.
On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked. Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.
Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.
In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it. Therefore
the code that sets it is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andiry Xu <andiry.xu@amd.com> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scheme used to index format in uvc_fixup_video_ctrl() is not robust:
format index is based on descriptor ordering, which does not necessarily
match bFormatIndex ordering. Searching for first matching format will
prevent uvc_fixup_video_ctrl() from using the wrong format/frame to make
adjustments.
We must not use dummy for index.
After the first index, READ32(dummy) will change dummy!!!!
Signed-off-by: Mi Jinlong <mijinlong@cn.fujitsu.com>
[bfields@redhat.com: Trond points out READ_BUF alone is sufficient.] Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use mask 0x10 for "soft cursor" detection on in function tile_cursor.
(Tile Blitting Operation in framebuffer console).
The old mask 0x01 for vc_cursor_type detects CUR_NONE, CUR_LOWER_THIRD
and every second mode value as "software cursor". This hides the cursor
for these modes (cursor.mode = 0). But, only CUR_NONE or "software cursor"
should hide the cursor.
See also 0x10 in functions add_softcursor, bit_cursor and cw_cursor.
Signed-off-by: Henry Nestler <henry.nestler@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While mm->start_stack was protected from cross-uid viewing (commit f83ce3e6b02d5 ("proc: avoid information leaks to non-privileged
processes")), the start_code and end_code values were not. This would
allow the text location of a PIE binary to leak, defeating ASLR.
Note that the value "1" is used instead of "0" for a protected value since
"ps", "killall", and likely other readers of /proc/pid/stat, take
start_code of "0" to mean a kernel thread and will misbehave. Thanks to
Brad Spengler for pointing this out.
The current code fails to print the "[heap]" marking if the heap is split
into multiple mappings.
Fix the check so that the marking is displayed in all possible cases:
1. vma matches exactly the heap
2. the heap vma is merged e.g. with bss
3. the heap vma is splitted e.g. due to locked pages
Test cases. In all cases, the process should have mapping(s) with
[heap] marking:
It looks like the bug has been there forever, and since it only results in
some information missing from a procfile, it does not fulfil the -stable
"critical issue" criteria.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Orphan cleanup is currently executed even if the file system has some
number of unknown ROCOMPAT features, which deletes inodes and frees
blocks, which could be very bad for some RO_COMPAT features.
This patch skips the orphan cleanup if it contains readonly compatible
features not known by this ext3 implementation, which would prevent
the fs from being mounted (or remounted) readwrite.
Signed-off-by: Amir Goldstein <amir73il@users.sf.net> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Userland should be able to trust the pid and uid of the sender of a
signal if the si_code is SI_TKILL.
Unfortunately, the kernel has historically allowed sigqueueinfo() to
send any si_code at all (as long as it was negative - to distinguish it
from kernel-generated signals like SIGILL etc), so it could spoof a
SI_TKILL with incorrect siginfo values.
Happily, it looks like glibc has always set si_code to the appropriate
SI_QUEUE, so there are probably no actual user code that ever uses
anything but the appropriate SI_QUEUE flag.
So just tighten the check for si_code (we used to allow any negative
value), and add a (one-time) warning in case there are binaries out
there that might depend on using other si_code values.
To quote Len Brown:
intel_idle was deemed a "feature", and thus not included in
2.6.33.stable, and thus 2.6.33.stable does not need this patch.
so I'm removing it.
Cc: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A successful write() to the "reset" sysfs attribute should return the
number of bytes written, not 0. Otherwise userspace (bash) retries the
write over and over again.
Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device doesn't support power management (pm_cap == 0) but it is
acpi_pci_power_manageable() because there is a _PS0 method declared for
it and _EJ0 is also declared for the slot then nobody is going to set
current_state = PCI_D0 for this device. This is what I think it is
happening:
pci_enable_device
|
__pci_enable_device_flags
/* here we do not set current_state because !pm_cap */
|
do_pci_enable_device
|
pci_set_power_state
|
__pci_start_power_transition
|
pci_platform_power_transition
/* platform_pci_power_manageable() calls acpi_pci_power_manageable that
* returns true */
|
platform_pci_set_power_state
/* acpi_pci_set_power_state gets called and does nothing because the
* acpi device has _EJ0, see the comment "If the ACPI device has _EJ0,
* ignore the device" */
at this point if we refer to the commit message that introduced the
comment above (10b3dcae0f275e2546e55303d64ddbb58cec7599), it is up to
the hotplug driver to set the state to D0.
However AFAICT the pci hotplug driver never does, in fact
drivers/pci/hotplug/acpiphp_glue.c:register_slot sets the slot flags to
(SLOT_ENABLED | SLOT_POWEREDON) but it does not set the pci device
current state to PCI_D0.
So my proposed fix is also to set current_state = PCI_D0 in
register_slot.
Comments are very welcome.
Up to 2.6.22, you could use remap_file_pages(2) on a tmpfs file or a
shared mapping of /dev/zero or a shared anonymous mapping. In 2.6.23 we
disabled it by default, but set VM_CAN_NONLINEAR to enable it on safe
mappings. We made sure to set it in shmem_mmap() for tmpfs files, but
missed it in shmem_zero_setup() for the others. Fix that at last.
The test program below will hang because io_getevents() uses
add_wait_queue_exclusive(), which means the wake_up() in io_destroy() only
wakes up one of the threads. Fix this by using wake_up_all() in the aio
code paths where we want to make sure no one gets stuck.
An integer overflow occurs in the calculation of RHlinear when the
relative humidity is greater than around 30%. The consequence is a subtle
(but noticeable) error in the resulting humidity measurement.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The latest binutils (2.21.0.20110302/Ubuntu) breaks the build
yet another time, under CONFIG_XEN=y due to a .size directive that
refers to a slightly differently named (hence, to the now very
strict and unforgiving assembler, non-existent) symbol.
[ mingo:
This unnecessary build breakage caused by new binutils
version 2.21 gets escallated back several kernel releases spanning
several years of Linux history, affecting over 130,000 upstream
kernel commits (!), on CONFIG_XEN=y 64-bit kernels (i.e. essentially
affecting all major Linux distro kernel configs).
Git annotate tells us that this slight debug symbol code mismatch
bug has been introduced in 2008 in commit 3d75e1b8:
Human reviewers almost never catch such small mismatches, and binutils
never even warned about it either.
This new binutils version thus breaks the Xen build on all upstream kernels
since v2.6.27, out of the blue.
This makes a straightforward Git bisection of all 64-bit Xen-enabled kernels
impossible on such binutils, for a bisection window of over hundred
thousand historic commits. (!)
This is a major fail on the side of binutils and binutils needs to turn
this show-stopper build failure into a warning ASAP. ]
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Jan Beulich <jbeulich@novell.com> Cc: H.J. Lu <hjl.tools@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Kees Cook <kees.cook@canonical.com>
LKML-Reference: <1299877178-26063-1-git-send-email-heukelum@fastmail.fm> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When trying to flash a machine via the update_flash command, Anton received the
following error:
Restarting system.
FLASH: kernel bug...flash list header addr above 4GB
The code in question has a comment that the flash list should be in
the kernel data and therefore under 4GB:
/* NOTE: the "first" block list is a global var with no data
* blocks in the kernel data segment. We do this because
* we want to ensure this block_list addr is under 4GB.
*/
Unfortunately the Kconfig option is marked tristate which means the variable
may not be in the kernel data and could be above 4GB.
Instead of relying on the data segment being below 4GB, use the static
data buffer allocated by the kernel for use by rtas. Since we don't
use the header struct directly anymore, convert it to a simple pointer.
Reported-By: Anton Blanchard <anton@samba.org> Signed-Off-By: Milton Miller <miltonm@bga.com> Tested-By: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we are crashing, the crashing/primary CPU IPIs the secondaries to
turn off IRQs, go into real mode and wait in kexec_wait. While this
is happening, the primary tears down all the MMU maps. Unfortunately
the primary doesn't check to make sure the secondaries have entered
real mode before doing this.
On PHYP machines, the secondaries can take a long time shutting down
the IRQ controller as RTAS calls are need. These RTAS calls need to
be serialised which resilts in the secondaries contending in
lock_rtas() and hence taking a long time to shut down.
We've hit this on large POWER7 machines, where some secondaries are
still waiting in lock_rtas(), when the primary tears down the HPTEs.
This patch makes sure all secondaries are in real mode before the
primary tears down the MMU. It uses the new kexec_state entry in the
paca. It times out if the secondaries don't reach real mode after
10sec.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Mike Galbraith reported finding a lockup ("perma-spin bug") where the
cpumask passed to smp_call_function_many was cleared by other cpu(s)
while a cpu was preparing its call_data block, resulting in no cpu to
clear the last ref and unlock the block.
Having cpus clear their bit asynchronously could be useful on a mask of
cpus that might have a translation context, or cpus that need a push to
complete an rcu window.
Instead of adding a BUG_ON and requiring yet another cpumask copy, just
detect the race and handle it.
Note: arch_send_call_function_ipi_mask must still handle an empty
cpumask because the data block is globally visible before the that arch
callback is made. And (obviously) there are no guarantees to which cpus
are notified if the mask is changed during the call; only cpus that were
online and had their mask bit set during the whole call are guaranteed
to be called.
Reported-by: Mike Galbraith <efault@gmx.de> Reported-by: Jan Beulich <JBeulich@novell.com> Acked-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the call to tty_ldisc_flush() from the RESULT_NO_CARRIER
branch of isdn_tty_modem_result(), as already proposed in commit 00409bb045887ec5e7b9e351bc080c38ab6bfd33.
This avoids a "sleeping function called from invalid context" BUG
when the hardware driver calls the statcallb() callback with
command==ISDN_STAT_DHUP in atomic context, which in turn calls
isdn_tty_modem_result(RESULT_NO_CARRIER, ~), and from there,
tty_ldisc_flush() which may sleep.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to intel CPU manual, every time PGD entry is changed in i386 PAE
mode, we need do a full TLB flush. Current code follows this and there is
comment for this too in the code.
But current code misses the multi-threaded case. A changed page table
might be used by several CPUs, every such CPU should flush TLB. Usually
this isn't a problem, because we prepopulate all PGD entries at process
fork. But when the process does munmap and follows new mmap, this issue
will be triggered.
When it happens, some CPUs keep doing page faults:
Paul McKenney's review pointed out two problems with the barriers in the
2.6.38 update to the smp call function many code.
First, a barrier that would force the func and info members of data to
be visible before their consumption in the interrupt handler was
missing. This can be solved by adding a smp_wmb between setting the
func and info members and setting setting the cpumask; this will pair
with the existing and required smp_rmb ordering the cpumask read before
the read of refs. This placement avoids the need a second smp_rmb in
the interrupt handler which would be executed on each of the N cpus
executing the call request. (I was thinking this barrier was present
but was not).
Second, the previous write to refs (establishing the zero that we the
interrupt handler was testing from all cpus) was performed by a third
party cpu. This would invoke transitivity which, as a recient or
concurrent addition to memory-barriers.txt now explicitly states, would
require a full smp_mb().
However, we know the cpumask will only be set by one cpu (the data
owner) and any preivous iteration of the mask would have cleared by the
reading cpu. By redundantly writing refs to 0 on the owning cpu before
the smp_wmb, the write to refs will follow the same path as the writes
that set the cpumask, which in turn allows us to keep the barrier in the
interrupt handler a smp_rmb instead of promoting it to a smp_mb (which
will be be executed by N cpus for each of the possible M elements on the
list).
I moved and expanded the comment about our (ab)use of the rcu list
primitives for the concurrent walk earlier into this function. I
considered moving the first two paragraphs to the queue list head and
lock, but felt it would have been too disconected from the code.
Cc: Paul McKinney <paulmck@linux.vnet.ibm.com> Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter pointed out there was nothing preventing the list_del_rcu in
smp_call_function_interrupt from running before the list_add_rcu in
smp_call_function_many.
Fix this by not setting refs until we have gotten the lock for the list.
Take advantage of the wmb in list_add_rcu to save an explicit additional
one.
I tried to force this race with a udelay before the lock & list_add and
by mixing all 64 online cpus with just 3 random cpus in the mask, but
was unsuccessful. Still, inspection shows a valid race, and the fix is
a extension of the existing protection window in the current code.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ext3_dx_add_entry() has to split an index node, it has to ensure that
name_len of dx_node's fake_dirent is also zero, because otherwise e2fsck
won't recognise it as an intermediate htree node and consider the htree to
be corrupted.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Events on POWER7 can roll back if a speculative event doesn't
eventually complete. Unfortunately in some rare cases they will
raise a performance monitor exception. We need to catch this to
ensure we reset the PMC. In all cases the PMC will be 256 or less
cycles from overflow.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110309143842.6c22845e@kryten> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a race in which the task->tk_callback() puts the rpc_task
to sleep, setting a new callback. Under certain circumstances, the current
code may end up executing the task->tk_action before it gets round to the
callback.
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com> Signed-off-by: Ilgu Hong <ilgu.hong@promise.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 280c73d ("PCI: centralize the capabilities code in
pci-sysfs.c") changed the initialisation of the "rom" and "vpd"
attributes, and made the failure path for the "vpd" attribute
incorrect. We must free the new attribute structure (attr), but
instead we currently free dev->vpd->attr. That will normally be NULL,
resulting in a memory leak, but it might be a stale pointer, resulting
in a double-free.
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk was added before SR-IOV was in production and now all machines that
originally had this issue alreayd have bios updates to correct the issue. The
quirk itself is no longer needed and in fact causes bugs if run. Remove it.
When the mux for digital mic is different from the mux for other mics,
the current auto-parser doesn't handle them in a right way but provides
only one mic. This patch fixes the issue.
The XFS_IOC_FSGETXATTR ioctl allows unprivileged users to read 12
bytes of uninitialized stack memory, because the fsxattr struct
declared on the stack in xfs_ioc_fsgetxattr() does not alter (or zero)
the 12-byte fsx_pad member before copying it back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Alex Elder <aelder@sgi.com> Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized
Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx,
see http://www.etheus.net/SiUSBXp_Linux_Driver for further info.
In the vhci_urb_dequeue() function the TCP connection is checked twice.
Each time when the TCP connection is closed the URB is unlinked and given
back. Remove the second attempt of unlinking and giving back of the URB completely.
This patch fixes the bug described at https://bugzilla.kernel.org/show_bug.cgi?id=24872 .
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sctp_packet_config() is called when getting the packet ready
for appending of chunks. The function should not touch the
current state, since it's possible to ping-pong between two
transports when sending, and that can result packet corruption
followed by skb overlfow crash.
Reported-by: Thomas Dreibholz <dreibh@iem.uni-due.de> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I may have an explanation for the LSI 1068 HBA hangs provoked by ATA
pass-through commands, in particular by smartctl.
First, my version of the symptoms. On an LSI SAS1068E B3 HBA running
01.29.00.00 firmware, with SATA disks, and with smartd running, I'm seeing
occasional task, bus, and host resets, some of which lead to hard faults of
the HBA requiring a reboot. Abusively looping the smartctl command,
# while true; do smartctl -a /dev/sdb > /dev/null; done
dramatically increases the frequency of these failures to nearly one per
minute. A high IO load through the HBA while looping smartctl seems to
improve the chance of a full scsi host reset or a non-recoverable hang.
I reduced what smartctl was doing down to a simple test case which
causes the hang with a single IO when pointed at the sd interface. See
the code at the bottom of this e-mail. It uses an SG_IO ioctl to issue
a single pass-through ATA identify device command. If the buffer
userspace gives for the read data has certain alignments, the task is
issued to the HBA but the HBA fails to respond. If run against the sg
interface, neither the test code nor smartctl causes a hang.
sd and sg handle the SG_IO ioctl slightly differently. Unless you
specifically set a flag to do direct IO, sg passes a buffer of its own,
which is page-aligned, to the block layer and later copies the result
into the userspace buffer regardless of its alignment. sd, on the other
hand, always does direct IO unless the userspace buffer fails an
alignment test at block/blk-map.c line 57, in which case a page-aligned
buffer is created and used for the transfer.
The alignment test currently checks for word-alignment, the default
setup by scsi_lib.c; therefore, userspace buffers of almost any
alignment are given directly to the HBA as DMA targets. The LSI 1068
hardware doesn't seem to like at least a couple of the alignments which
cross a page boundary (see the test code below). Curiously, many
page-boundary-crossing alignments do work just fine.
So, either the hardware has an bug handling certain alignments or the
hardware has a stricter alignment requirement than the driver is
advertising. If stricter alignment is required, then in no case should
misaligned buffers from userspace be allowed through without being
bounced or at least causing an error to be returned.
It seems the mptsas driver could use blk_queue_dma_alignment() to advertise
a stricter alignment requirement. If it does, sd does the right thing and
bounces misaligned buffers (see block/blk-map.c line 57). The following
patch to 2.6.34-rc5 makes my symptoms go away. I'm sure this is the wrong
place for this code, but it gets my idea across.
We have 32-bit variable overflow possibility when multiply in
task_times() and thread_group_times() functions. When the
overflow happens then the scaled utime value becomes erroneously
small and the scaled stime becomes i erroneously big.
It turns out that the setpgid() system call fails to enter an RCU
read-side critical section before doing a PID-to-task_struct translation.
This commit therefore does rcu_read_lock() before the translation, and
also does rcu_read_unlock() after the last use of the returned pointer.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: David Howells <dhowells@redhat.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pcpu_first/last_unit_cpu are used to track which cpu has the first and
last units assigned. This in turn is used to determine the span of a
chunk for man/unmap cache flushes and whether an address belongs to
the first chunk or not in per_cpu_ptr_to_phys().
When the number of possible CPUs isn't power of two, a chunk may
contain unassigned units towards the end of a chunk. The logic to
determine pcpu_last_unit_cpu was incorrect when there was an unused
unit at the end of a chunk. It failed to ignore the unused unit and
assigned the unused marker NR_CPUS to pcpu_last_unit_cpu.
This was discovered through kdump failure which was caused by
malfunctioning per_cpu_ptr_to_phys() on a kvm setup with 50 possible
CPUs by CAI Qian.
When allocating a page, the system uses NR_FREE_PAGES counters to
determine if watermarks would remain intact after the allocation was made.
This check is made without interrupts disabled or the zone lock held and
so is race-prone by nature. Unfortunately, when pages are being freed in
batch, the counters are updated before the pages are added on the list.
During this window, the counters are misleading as the pages do not exist
yet. When under significant pressure on systems with large numbers of
CPUs, it's possible for processes to make progress even though they should
have been stalled. This is particularly problematic if a number of the
processes are using GFP_ATOMIC as the min watermark can be accidentally
breached and in extreme cases, the system can livelock.
This patch updates the counters after the pages have been added to the
list. This makes the allocator more cautious with respect to preserving
the watermarks and mitigates livelock possibilities.
[akpm@linux-foundation.org: avoid modifying incoming args] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Christoph Lameter <cl@linux.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When under significant memory pressure, a process enters direct reclaim
and immediately afterwards tries to allocate a page. If it fails and no
further progress is made, it's possible the system will go OOM. However,
on systems with large amounts of memory, it's possible that a significant
number of pages are on per-cpu lists and inaccessible to the calling
process. This leads to a process entering direct reclaim more often than
it should increasing the pressure on the system and compounding the
problem.
This patch notes that if direct reclaim is making progress but allocations
are still failing that the system is already under heavy pressure. In
this case, it drains the per-cpu lists and tries the allocation a second
time before continuing.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Reviewed-by: Christoph Lameter <cl@linux.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ordinarily watermark checks are based on the vmstat NR_FREE_PAGES as it is
cheaper than scanning a number of lists. To avoid synchronization
overhead, counter deltas are maintained on a per-cpu basis and drained
both periodically and when the delta is above a threshold. On large CPU
systems, the difference between the estimated and real value of
NR_FREE_PAGES can be very high. If NR_FREE_PAGES is much higher than
number of real free page in buddy, the VM can allocate pages below min
watermark, at worst reducing the real number of pages to zero. Even if
the OOM killer kills some victim for freeing memory, it may not free
memory if the exit path requires a new page resulting in livelock.
This patch introduces a zone_page_state_snapshot() function (courtesy of
Christoph) that takes a slightly more accurate view of an arbitrary vmstat
counter. It is used to read NR_FREE_PAGES while kswapd is awake to avoid
the watermark being accidentally broken. The estimate is not perfect and
may result in cache line bounces but is expected to be lighter than the
IPI calls necessary to continually drain the per-cpu counters while kswapd
is awake.
Signed-off-by: Christoph Lameter <cl@linux.com> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug in keyctl_session_to_parent() whereby it tries to check the ownership
of the parent process's session keyring whether or not the parent has a session
keyring [CVE-2010-2960].
If the system is using pam_keyinit then it mostly protected against this as all
processes derived from a login will have inherited the session keyring created
by pam_keyinit during the log in procedure.
To test this, pam_keyinit calls need to be commented out in /etc/pam.d/.
There's an protected access to the parent process's credentials in the middle
of keyctl_session_to_parent(). This results in the following RCU warning:
Tony's fix (f574c843191728d9407b766a027f779dcd27b272) has a small bug,
it incorrectly uses "r3" as a scratch register in the first of the two
unlock paths ... it is also inefficient. Optimize the fast path again.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ia64 converted to using ticket locks, an inline implementation
of trylock/unlock in fsys.S was missed. This was not noticed because
in most circumstances it simply resulted in using the slow path because
the siglock was apparently not available (under old spinlock rules).
Problems occur when the ticket spinlock has value 0x0 (when first
initialised, or when it wraps around). At this point the fsys.S
code acquires the lock (changing the 0x0 to 0x1. If another process
attempts to get the lock at this point, it will change the value from
0x1 to 0x2 (using new ticket lock rules). Then the fsys.S code will
free the lock using old spinlock rules by writing 0x0 to it. From
here a variety of bad things can happen.
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
projects / karo-tx-linux.git / log