ARM: sun8i: Add Parrot Board DTS

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3fde2eb0680e722cd4171f8fd827edbda7a6dfd1..016611da6d5aa651c87723580e8396cd4eb892d6 100644 (file)
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -767,7 +767,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
        sun8i-h3-orangepi-one.dtb \
        sun8i-h3-orangepi-pc.dtb \
        sun8i-h3-orangepi-plus.dtb \
-       sun8i-h3-sinovoip-bpi-m2-plus.dtb
+       sun8i-h3-sinovoip-bpi-m2-plus.dtb \
+       sun8i-r16-parrot.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
        sun9i-a80-optimus.dtb \
        sun9i-a80-cubieboard4.dtb

diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts
new file mode 100644 (file)
index 0000000..47553e5
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts
@@ -0,0 +1,351 @@
+/*
+ * Copyright 2016 Quentin Schulz
+ *
+ * Quentin Schulz <quentin.schulz@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       model = "Allwinner R16 EVB (Parrot)";
+       compatible = "allwinner,parrot", "allwinner,sun8i-a33";
+
+       aliases {
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+               pinctrl-0 = <&led_pins_parrot>;
+
+               led1 {
+                       label = "parrot:led1:usr";
+                       gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+               };
+
+               led2 {
+                       label = "parrot:led2:usr";
+                       gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+               };
+       };
+
+       wifi_pwrseq: wifi_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+       };
+
+};
+
+&ehci0 {
+       status = "okay";
+};
+
+&i2c1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c1_pins_a>;
+       status = "okay";
+
+       /*
+        * FIXME: An as-yet-unknown accelerometer is connected to this
+        * i2c bus.
+        */
+};
+
+&lradc {
+       vref-supply = <&reg_aldo3>;
+       status = "okay";
+
+       button@0 {
+               label = "V+";
+               linux,code = <KEY_VOLUMEUP>;
+               channel = <0>;
+               voltage = <190000>;
+       };
+
+       button@1 {
+               label = "V-";
+               linux,code = <KEY_VOLUMEDOWN>;
+               channel = <0>;
+               voltage = <390000>;
+       };
+
+};
+
+&mmc0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot>;
+       vmmc-supply = <&reg_dcdc1>;
+       cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+       bus-width = <4>;
+       status = "okay";
+};
+
+&mmc1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_parrot>;
+       vmmc-supply = <&reg_aldo1>;
+       mmc-pwrseq = <&wifi_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+};
+
+&mmc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_8bit_pins>;
+       vmmc-supply = <&reg_dcdc1>;
+       bus-width = <8>;
+       non-removable;
+       cap-mmc-hw-reset;
+       status = "okay";
+};
+
+&mmc2_8bit_pins {
+       allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+       allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+       status = "okay";
+};
+
+&pio {
+       mmc0_cd_pin_parrot: mmc0_cd_pin@0 {
+               allwinner,pins = "PD14";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+
+       led_pins_parrot: led_pins@0 {
+               allwinner,pins = "PE16", "PE17";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       usb0_id_det: usb0_id_detect_pin@0 {
+               allwinner,pins = "PD10";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+
+       usb1_vbus_pin_parrot: usb1_vbus_pin@0 {
+               allwinner,pins = "PD12";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+};
+
+&r_pio {
+       wifi_reset_pin_parrot: wifi_reset_pin@0 {
+               allwinner,pins = "PL6";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+};
+
+&r_rsb {
+       status = "okay";
+
+       axp22x: pmic@3a3 {
+               compatible = "x-powers,axp223";
+               reg = <0x3a3>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               drivevbus-supply = <&reg_vcc5v0>;
+               x-powers,drive-vbus-en;
+       };
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+       regulator-always-on;
+       regulator-min-microvolt = <2350000>;
+       regulator-max-microvolt = <2650000>;
+       regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+       regulator-always-on;
+       regulator-min-microvolt = <2700000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc5ldo {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+       regulator-always-on;
+       regulator-min-microvolt = <1500000>;
+       regulator-max-microvolt = <1500000>;
+       regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+       /*
+        * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+        * Remove next line once it is possible to sync two regulators.
+        */
+       regulator-always-on;
+       regulator-min-microvolt = <3300000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-wifi0";
+};
+
+&reg_dldo2 {
+       /*
+        * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+        * Remove next line once it is possible to sync two regulators.
+        */
+       regulator-always-on;
+       regulator-min-microvolt = <3300000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-wifi1";
+};
+
+&reg_dldo3 {
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v0-csi";
+};
+
+&reg_drivevbus {
+       regulator-name = "usb0-vbus";
+       status = "okay";
+};
+
+&reg_eldo1 {
+       regulator-min-microvolt = <1200000>;
+       regulator-max-microvolt = <1200000>;
+       regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_eldo2 {
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-dsp";
+};
+
+&reg_eldo3 {
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "eldo3";
+};
+
+&reg_usb1_vbus {
+       pinctrl-names = "default";
+       pinctrl-0 = <&usb1_vbus_pin_parrot>;
+       gpio = <&pio 3 12 GPIO_ACTIVE_HIGH>; /* PD12 */
+       status = "okay";
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins_b>;
+       status = "okay";
+};
+
+&usb_otg {
+       dr_mode = "otg";
+       status = "okay";
+};
+
+&usb_power_supply {
+       status = "okay";
+};
+
+&usbphy {
+       status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&usb0_id_det>;
+       usb0_vbus-supply = <&reg_drivevbus>;
+       usb0_id_det-gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10 */
+       usb0_vbus_power-supply = <&usb_power_supply>;
+       usb1_vbus-supply = <&reg_usb1_vbus>;
+};