--- /dev/null
+MMUv3 initialization sequence.
+
+The code in the initialize_mmu macro sets up MMUv3 memory mapping
+identically to MMUv2 fixed memory mapping. Depending on
+CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX symbol this code is
+located in one of the following address ranges:
+
+ 0xF0000000..0xFFFFFFFF (will keep same address in MMU v2 layout;
+ typically ROM)
+ 0x00000000..0x07FFFFFF (system RAM; this code is actually linked
+ at 0xD0000000..0xD7FFFFFF [cached]
+ or 0xD8000000..0xDFFFFFFF [uncached];
+ in any case, initially runs elsewhere
+ than linked, so have to be careful)
+
+The code has the following assumptions:
+ This code fragment is run only on an MMU v3.
+ TLBs are in their reset state.
+ ITLBCFG and DTLBCFG are zero (reset state).
+ RASID is 0x04030201 (reset state).
+ PS.RING is zero (reset state).
+ LITBASE is zero (reset state, PC-relative literals); required to be PIC.
+
+TLB setup proceeds along the following steps.
+
+ Legend:
+ VA = virtual address (two upper nibbles of it);
+ PA = physical address (two upper nibbles of it);
+ pc = physical range that contains this code;
+
+After step 2, we jump to virtual address in 0x40000000..0x5fffffff
+that corresponds to next instruction to execute in this code.
+After step 4, we jump to intended (linked) address of this code.
+
+ Step 0 Step1 Step 2 Step3 Step 4 Step5
+ ============ ===== ============ ===== ============ =====
+ VA PA PA VA PA PA VA PA PA
+ ------ -- -- ------ -- -- ------ -- --
+ E0..FF -> E0 -> E0 E0..FF -> E0 F0..FF -> F0 -> F0
+ C0..DF -> C0 -> C0 C0..DF -> C0 E0..EF -> F0 -> F0
+ A0..BF -> A0 -> A0 A0..BF -> A0 D8..DF -> 00 -> 00
+ 80..9F -> 80 -> 80 80..9F -> 80 D0..D7 -> 00 -> 00
+ 60..7F -> 60 -> 60 60..7F -> 60
+ 40..5F -> 40 40..5F -> pc -> pc 40..5F -> pc
+ 20..3F -> 20 -> 20 20..3F -> 20
+ 00..1F -> 00 -> 00 00..1F -> 00
-config FRAME_POINTER
- def_bool n
-
config ZONE_DMA
def_bool y
config XTENSA
def_bool y
+ select ARCH_WANT_FRAME_POINTERS
select HAVE_IDE
select GENERIC_ATOMIC64
select HAVE_GENERIC_HARDIRQS
source "init/Kconfig"
source "kernel/Kconfig.freezer"
+config LOCKDEP_SUPPORT
+ def_bool y
+
+config STACKTRACE_SUPPORT
+ def_bool y
+
+config TRACE_IRQFLAGS_SUPPORT
+ def_bool y
+
config MMU
def_bool n
help
Can we use information of configuration file?
+config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
+ bool "Initialize Xtensa MMU inside the Linux kernel code"
+ default y
+ help
+ Earlier version initialized the MMU in the exception vector
+ before jumping to _startup in head.S and had an advantage that
+ it was possible to place a software breakpoint at 'reset' and
+ then enter your normal kernel breakpoints once the MMU was mapped
+ to the kernel mappings (0XC0000000).
+
+ This unfortunately doesn't work for U-Boot and likley also wont
+ work for using KEXEC to have a hot kernel ready for doing a
+ KDUMP.
+
+ So now the MMU is initialized in head.S but it's necessary to
+ use hardware breakpoints (gdb 'hbreak' cmd) to break at _startup.
+ xt-gdb can't place a Software Breakpoint in the 0XD region prior
+ to mapping the MMU and after mapping even if the area of low memory
+ was mapped gdb wouldn't remove the breakpoint on hitting it as the
+ PC wouldn't match. Since Hardware Breakpoints are recommended for
+ Linux configurations it seems reasonable to just assume they exist
+ and leave this older mechanism for unfortunate souls that choose
+ not to follow Tensilica's recommendation.
+
+ Selecting this will cause U-Boot to set the KERNEL Load and Entry
+ address at 0x00003000 instead of the mapped std of 0xD0003000.
+
+ If in doubt, say Y.
+
endmenu
config XTENSA_CALIBRATE_CCOUNT
menu "Executable file formats"
-# only elf supported
-config KCORE_ELF
- def_bool y
- depends on PROC_FS
- help
- If you enabled support for /proc file system then the file
- /proc/kcore will contain the kernel core image in ELF format. This
- can be used in gdb:
-
- $ cd /usr/src/linux ; gdb vmlinux /proc/kcore
-
- This is especially useful if you have compiled the kernel with the
- "-g" option to preserve debugging information. It is mainly used
- for examining kernel data structures on the live kernel.
-
source "fs/Kconfig.binfmt"
endmenu
export OBJCOPY_ARGS
export CPPFLAGS_boot.lds += -P -C
+export KBUILD_AFLAGS += -mtext-section-literals
boot-y := bootstrap.o
-#include <variant/core.h>
+/*
+ * linux/arch/xtensa/boot/boot-elf/boot.lds.S
+ *
+ * Copyright (C) 2008 - 2013 by Tensilica Inc.
+ *
+ * Chris Zankel <chris@zankel.net>
+ * Marc Gauthier <marc@tensilica.com
+ * Pete Delaney <piet@tensilica.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <asm/vectors.h>
OUTPUT_ARCH(xtensa)
ENTRY(_ResetVector)
SECTIONS
{
- .start 0xD0000000 : { *(.start) }
-
- .text 0xD0000000:
- {
- __reloc_start = . ;
- _text_start = . ;
- *(.literal .text.literal .text)
- _text_end = . ;
- }
-
- .rodata ALIGN(0x04):
- {
- *(.rodata)
- *(.rodata1)
- }
-
- .data ALIGN(0x04):
+ .ResetVector.text XCHAL_RESET_VECTOR_VADDR :
{
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.got.plt)
- *(.got)
- *(.dynamic)
+ *(.ResetVector.text)
}
- __reloc_end = . ;
-
- . = ALIGN(0x10);
- __image_load = . ;
- .image 0xd0001000:
+ .image KERNELOFFSET: AT (LOAD_MEMORY_ADDRESS)
{
_image_start = .;
*(image)
_image_end = . ;
}
-
.bss ((LOADADDR(.image) + SIZEOF(.image) + 3) & ~ 3):
{
__bss_start = .;
*(.bss)
__bss_end = .;
}
- _end = .;
- _param_start = .;
- .ResetVector.text XCHAL_RESET_VECTOR_VADDR :
+ /*
+ * This is a remapped copy of the Reset Vector Code.
+ * It keeps gdb in sync with the PC after switching
+ * to the temporary mapping used while setting up
+ * the V2 MMU mappings for Linux.
+ */
+ .ResetVector.remapped_text 0x46000000 (INFO):
{
- *(.ResetVector.text)
+ *(.ResetVector.remapped_text)
}
-
-
- PROVIDE (end = .);
}
+/*
+ * arch/xtensa/boot/boot-elf/bootstrap.S
+ *
+ * Low-level exception handling
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004 - 2013 by Tensilica Inc.
+ *
+ * Chris Zankel <chris@zankel.net>
+ * Marc Gauthier <marc@tensilica.com>
+ * Piet Delaney <piet@tensilica.com>
+ */
#include <asm/bootparam.h>
+#include <asm/processor.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/cacheasm.h>
+#include <asm/initialize_mmu.h>
+#include <linux/linkage.h>
-
-/* ResetVector
- */
- .section .ResetVector.text, "ax"
+ .section .ResetVector.text, "ax"
.global _ResetVector
+ .global reset
+
_ResetVector:
- _j reset
+ _j _SetupMMU
+
+ .begin no-absolute-literals
+ .literal_position
+
.align 4
RomInitAddr:
- .word 0xd0001000
+#if defined(CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX) && \
+ XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY
+ .word 0x00003000
+#else
+ .word 0xd0003000
+#endif
RomBootParam:
.word _bootparam
+_bootparam:
+ .short BP_TAG_FIRST
+ .short 4
+ .long BP_VERSION
+ .short BP_TAG_LAST
+ .short 0
+ .long 0
+
+ .align 4
+_SetupMMU:
+ movi a0, 0
+ wsr a0, windowbase
+ rsync
+ movi a0, 1
+ wsr a0, windowstart
+ rsync
+ movi a0, 0x1F
+ wsr a0, ps
+ rsync
+
+ Offset = _SetupMMU - _ResetVector
+
+#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
+ initialize_mmu
+#endif
+
+ .end no-absolute-literals
+
+ rsil a0, XCHAL_DEBUGLEVEL-1
+ rsync
reset:
l32r a0, RomInitAddr
l32r a2, RomBootParam
jx a0
.align 4
- .section .bootstrap.data, "aw"
- .globl _bootparam
-_bootparam:
- .short BP_TAG_FIRST
- .short 4
- .long BP_VERSION
- .short BP_TAG_LAST
- .short 0
- .long 0
+ .section .ResetVector.remapped_text, "x"
+ .global _RemappedResetVector
+
+ /* Do org before literals */
+ .org 0
+
+_RemappedResetVector:
+ .begin no-absolute-literals
+ .literal_position
+
+ _j _RemappedSetupMMU
+
+ /* Position Remapped code at the same location as the original code */
+ . = _RemappedResetVector + Offset
+
+_RemappedSetupMMU:
+#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
+ initialize_mmu
+#endif
+
+ .end no-absolute-literals
. = ALIGN(0x10);
__image_load = . ;
- .image 0xd0001000: AT(__image_load)
+ .image 0xd0003000: AT(__image_load)
{
_image_start = .;
*(image)
# for more details.
#
-UIMAGE_LOADADDR = 0xd0001000
+ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
+UIMAGE_LOADADDR = 0x00003000
+else
+UIMAGE_LOADADDR = 0xd0003000
+endif
UIMAGE_COMPRESSION = gzip
$(obj)/../uImage: vmlinux.bin.gz FORCE
generic-y += kdebug.h
generic-y += kmap_types.h
generic-y += kvm_para.h
+generic-y += linkage.h
generic-y += local.h
generic-y += local64.h
generic-y += percpu.h
-/* empty */
+/*
+ * arch/xtensa/include/asm/ftrace.h
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2013 Tensilica Inc.
+ */
+#ifndef _XTENSA_FTRACE_H
+#define _XTENSA_FTRACE_H
+
+#include <asm/processor.h>
+
+#define HAVE_ARCH_CALLER_ADDR
+#define CALLER_ADDR0 ({ unsigned long a0, a1; \
+ __asm__ __volatile__ ( \
+ "mov %0, a0\n" \
+ "mov %1, a1\n" \
+ : "=r"(a0), "=r"(a1) : : ); \
+ MAKE_PC_FROM_RA(a0, a1); })
+#ifdef CONFIG_FRAME_POINTER
+extern unsigned long return_address(unsigned level);
+#define CALLER_ADDR1 return_address(1)
+#define CALLER_ADDR2 return_address(2)
+#define CALLER_ADDR3 return_address(3)
+#else
+#define CALLER_ADDR1 (0)
+#define CALLER_ADDR2 (0)
+#define CALLER_ADDR3 (0)
+#endif
+
+#endif /* _XTENSA_FTRACE_H */
#ifndef _XTENSA_INITIALIZE_MMU_H
#define _XTENSA_INITIALIZE_MMU_H
+#include <asm/pgtable.h>
+#include <asm/vectors.h>
+
#ifdef __ASSEMBLY__
#define XTENSA_HWVERSION_RC_2009_0 230000
* (XCHAL_HW_MIN_VERSION >= XTENSA_HWVERSION_RC_2009_0)
*/
+#if defined(CONFIG_MMU) && XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY
+/*
+ * Have MMU v3
+ */
+
+#if !XCHAL_HAVE_VECBASE
+# error "MMU v3 requires reloc vectors"
+#endif
+
+ movi a1, 0
+ _call0 1f
+ _j 2f
+
+ .align 4
+1: movi a2, 0x10000000
+ movi a3, 0x18000000
+ add a2, a2, a0
+9: bgeu a2, a3, 9b /* PC is out of the expected range */
+
+ /* Step 1: invalidate mapping at 0x40000000..0x5FFFFFFF. */
+
+ movi a2, 0x40000006
+ idtlb a2
+ iitlb a2
+ isync
+
+ /* Step 2: map 0x40000000..0x47FFFFFF to paddr containing this code
+ * and jump to the new mapping.
+ */
+#define CA_BYPASS (_PAGE_CA_BYPASS | _PAGE_HW_WRITE | _PAGE_HW_EXEC)
+#define CA_WRITEBACK (_PAGE_CA_WB | _PAGE_HW_WRITE | _PAGE_HW_EXEC)
+
+ srli a3, a0, 27
+ slli a3, a3, 27
+ addi a3, a3, CA_BYPASS
+ addi a7, a2, -1
+ wdtlb a3, a7
+ witlb a3, a7
+ isync
+
+ slli a4, a0, 5
+ srli a4, a4, 5
+ addi a5, a2, -6
+ add a4, a4, a5
+ jx a4
+
+ /* Step 3: unmap everything other than current area.
+ * Start at 0x60000000, wrap around, and end with 0x20000000
+ */
+2: movi a4, 0x20000000
+ add a5, a2, a4
+3: idtlb a5
+ iitlb a5
+ add a5, a5, a4
+ bne a5, a2, 3b
+
+ /* Step 4: Setup MMU with the old V2 mappings. */
+ movi a6, 0x01000000
+ wsr a6, ITLBCFG
+ wsr a6, DTLBCFG
+ isync
+
+ movi a5, 0xd0000005
+ movi a4, CA_WRITEBACK
+ wdtlb a4, a5
+ witlb a4, a5
+
+ movi a5, 0xd8000005
+ movi a4, CA_BYPASS
+ wdtlb a4, a5
+ witlb a4, a5
+
+ movi a5, 0xe0000006
+ movi a4, 0xf0000000 + CA_WRITEBACK
+ wdtlb a4, a5
+ witlb a4, a5
+
+ movi a5, 0xf0000006
+ movi a4, 0xf0000000 + CA_BYPASS
+ wdtlb a4, a5
+ witlb a4, a5
+
+ isync
+
+ /* Jump to self, using MMU v2 mappings. */
+ movi a4, 1f
+ jx a4
+
+1:
+ movi a2, VECBASE_RESET_VADDR
+ wsr a2, vecbase
+
+ /* Step 5: remove temporary mapping. */
+ idtlb a7
+ iitlb a7
+ isync
+
+ movi a0, 0
+ wsr a0, ptevaddr
+ rsync
+
+#endif /* defined(CONFIG_MMU) && XCHAL_HAVE_PTP_MMU &&
+ XCHAL_HAVE_SPANNING_WAY */
+
.endm
#endif /*__ASSEMBLY__*/
static inline bool arch_irqs_disabled_flags(unsigned long flags)
{
- return (flags & 0xf) != 0;
+#if XCHAL_EXCM_LEVEL < LOCKLEVEL || (1 << PS_EXCM_BIT) < LOCKLEVEL
+#error "XCHAL_EXCM_LEVEL and 1<<PS_EXCM_BIT must be no less than LOCKLEVEL"
+#endif
+ return (flags & (PS_INTLEVEL_MASK | (1 << PS_EXCM_BIT))) >= LOCKLEVEL;
}
static inline bool arch_irqs_disabled(void)
+++ /dev/null
-/*
- * include/asm-xtensa/linkage.h
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2001 - 2005 Tensilica Inc.
- */
-
-#ifndef _XTENSA_LINKAGE_H
-#define _XTENSA_LINKAGE_H
-
-/* Nothing to do here ... */
-
-#endif /* _XTENSA_LINKAGE_H */
--- /dev/null
+/*
+ * arch/xtensa/include/asm/stacktrace.h
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001 - 2013 Tensilica Inc.
+ */
+#ifndef _XTENSA_STACKTRACE_H
+#define _XTENSA_STACKTRACE_H
+
+#include <linux/sched.h>
+
+struct stackframe {
+ unsigned long pc;
+ unsigned long sp;
+};
+
+static __always_inline unsigned long *stack_pointer(struct task_struct *task)
+{
+ unsigned long *sp;
+
+ if (!task || task == current)
+ __asm__ __volatile__ ("mov %0, a1\n" : "=a"(sp));
+ else
+ sp = (unsigned long *)task->thread.sp;
+
+ return sp;
+}
+
+void walk_stackframe(unsigned long *sp,
+ int (*fn)(struct stackframe *frame, void *data),
+ void *data);
+
+#endif /* _XTENSA_STACKTRACE_H */
#define _INTLEVEL(x) XCHAL_INT ## x ## _LEVEL
#define INTLEVEL(x) _INTLEVEL(x)
-#if INTLEVEL(XCHAL_TIMER0_INTERRUPT) <= XCHAL_EXCM_LEVEL
+#if XCHAL_NUM_TIMERS > 0 && \
+ INTLEVEL(XCHAL_TIMER0_INTERRUPT) <= XCHAL_EXCM_LEVEL
# define LINUX_TIMER 0
# define LINUX_TIMER_INT XCHAL_TIMER0_INTERRUPT
-#elif INTLEVEL(XCHAL_TIMER1_INTERRUPT) <= XCHAL_EXCM_LEVEL
+#elif XCHAL_NUM_TIMERS > 1 && \
+ INTLEVEL(XCHAL_TIMER1_INTERRUPT) <= XCHAL_EXCM_LEVEL
# define LINUX_TIMER 1
# define LINUX_TIMER_INT XCHAL_TIMER1_INTERRUPT
-#elif INTLEVEL(XCHAL_TIMER2_INTERRUPT) <= XCHAL_EXCM_LEVEL
+#elif XCHAL_NUM_TIMERS > 2 && \
+ INTLEVEL(XCHAL_TIMER2_INTERRUPT) <= XCHAL_EXCM_LEVEL
# define LINUX_TIMER 2
# define LINUX_TIMER_INT XCHAL_TIMER2_INTERRUPT
#else
static inline void spill_registers(void)
{
- unsigned int a0, ps;
__asm__ __volatile__ (
- "movi a14, " __stringify(PS_EXCM_BIT | LOCKLEVEL) "\n\t"
+ "movi a14, "__stringify((1 << PS_EXCM_BIT) | LOCKLEVEL)"\n\t"
"mov a12, a0\n\t"
"rsr a13, sar\n\t"
"xsr a14, ps\n\t"
"mov a0, a12\n\t"
"wsr a13, sar\n\t"
"wsr a14, ps\n\t"
- : : "a" (&a0), "a" (&ps)
+ : :
#if defined(CONFIG_FRAME_POINTER)
: "a2", "a3", "a4", "a11", "a12", "a13", "a14", "a15",
#else
--- /dev/null
+/*
+ * arch/xtensa/include/asm/xchal_vaddr_remap.h
+ *
+ * Xtensa macros for MMU V3 Support. Deals with re-mapping the Virtual
+ * Memory Addresses from "Virtual == Physical" to their prevvious V2 MMU
+ * mappings (KSEG at 0xD0000000 and KIO at 0XF0000000).
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 - 2012 Tensilica Inc.
+ *
+ * Pete Delaney <piet@tensilica.com>
+ * Marc Gauthier <marc@tensilica.com
+ */
+
+#ifndef _XTENSA_VECTORS_H
+#define _XTENSA_VECTORS_H
+
+#include <variant/core.h>
+
+#if defined(CONFIG_MMU)
+
+/* Will Become VECBASE */
+#define VIRTUAL_MEMORY_ADDRESS 0xD0000000
+
+/* Image Virtual Start Address */
+#define KERNELOFFSET 0xD0003000
+
+#if defined(XCHAL_HAVE_PTP_MMU) && XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY
+ /* MMU v3 - XCHAL_HAVE_PTP_MMU == 1 */
+ #define PHYSICAL_MEMORY_ADDRESS 0x00000000
+ #define LOAD_MEMORY_ADDRESS 0x00003000
+#else
+ /* MMU V2 - XCHAL_HAVE_PTP_MMU == 0 */
+ #define PHYSICAL_MEMORY_ADDRESS 0xD0000000
+ #define LOAD_MEMORY_ADDRESS 0xD0003000
+#endif
+
+#else /* !defined(CONFIG_MMU) */
+ /* MMU Not being used - Virtual == Physical */
+
+ /* VECBASE */
+ #define VIRTUAL_MEMORY_ADDRESS 0x00002000
+
+ /* Location of the start of the kernel text, _start */
+ #define KERNELOFFSET 0x00003000
+ #define PHYSICAL_MEMORY_ADDRESS 0x00000000
+
+ /* Loaded just above possibly live vectors */
+ #define LOAD_MEMORY_ADDRESS 0x00003000
+
+#endif /* CONFIG_MMU */
+
+#define XC_VADDR(offset) (VIRTUAL_MEMORY_ADDRESS + offset)
+#define XC_PADDR(offset) (PHYSICAL_MEMORY_ADDRESS + offset)
+
+/* Used to set VECBASE register */
+#define VECBASE_RESET_VADDR VIRTUAL_MEMORY_ADDRESS
+
+#define RESET_VECTOR_VECOFS (XCHAL_RESET_VECTOR_VADDR - \
+ VECBASE_RESET_VADDR)
+#define RESET_VECTOR_VADDR XC_VADDR(RESET_VECTOR_VECOFS)
+
+#define RESET_VECTOR1_VECOFS (XCHAL_RESET_VECTOR1_VADDR - \
+ VECBASE_RESET_VADDR)
+#define RESET_VECTOR1_VADDR XC_VADDR(RESET_VECTOR1_VECOFS)
+
+#if XCHAL_HAVE_VECBASE
+
+#define USER_VECTOR_VADDR XC_VADDR(XCHAL_USER_VECOFS)
+#define KERNEL_VECTOR_VADDR XC_VADDR(XCHAL_KERNEL_VECOFS)
+#define DOUBLEEXC_VECTOR_VADDR XC_VADDR(XCHAL_DOUBLEEXC_VECOFS)
+#define WINDOW_VECTORS_VADDR XC_VADDR(XCHAL_WINDOW_OF4_VECOFS)
+#define INTLEVEL2_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL2_VECOFS)
+#define INTLEVEL3_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL3_VECOFS)
+#define INTLEVEL4_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL4_VECOFS)
+#define INTLEVEL5_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL5_VECOFS)
+#define INTLEVEL6_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL6_VECOFS)
+
+#define DEBUG_VECTOR_VADDR XC_VADDR(XCHAL_DEBUG_VECOFS)
+
+#undef XCHAL_NMI_VECTOR_VADDR
+#define XCHAL_NMI_VECTOR_VADDR XC_VADDR(XCHAL_NMI_VECOFS)
+
+#undef XCHAL_INTLEVEL7_VECTOR_VADDR
+#define XCHAL_INTLEVEL7_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL7_VECOFS)
+
+/*
+ * These XCHAL_* #defines from varian/core.h
+ * are not valid to use with V3 MMU. Non-XCHAL
+ * constants are defined above and should be used.
+ */
+#undef XCHAL_VECBASE_RESET_VADDR
+#undef XCHAL_RESET_VECTOR0_VADDR
+#undef XCHAL_USER_VECTOR_VADDR
+#undef XCHAL_KERNEL_VECTOR_VADDR
+#undef XCHAL_DOUBLEEXC_VECTOR_VADDR
+#undef XCHAL_WINDOW_VECTORS_VADDR
+#undef XCHAL_INTLEVEL2_VECTOR_VADDR
+#undef XCHAL_INTLEVEL3_VECTOR_VADDR
+#undef XCHAL_INTLEVEL4_VECTOR_VADDR
+#undef XCHAL_INTLEVEL5_VECTOR_VADDR
+#undef XCHAL_INTLEVEL6_VECTOR_VADDR
+#undef XCHAL_DEBUG_VECTOR_VADDR
+#undef XCHAL_NMI_VECTOR_VADDR
+#undef XCHAL_INTLEVEL7_VECTOR_VADDR
+
+#else
+
+#define USER_VECTOR_VADDR XCHAL_USER_VECTOR_VADDR
+#define KERNEL_VECTOR_VADDR XCHAL_KERNEL_VECTOR_VADDR
+#define DOUBLEEXC_VECTOR_VADDR XCHAL_DOUBLEEXC_VECTOR_VADDR
+#define WINDOW_VECTORS_VADDR XCHAL_WINDOW_VECTORS_VADDR
+#define INTLEVEL2_VECTOR_VADDR XCHAL_INTLEVEL2_VECTOR_VADDR
+#define INTLEVEL3_VECTOR_VADDR XCHAL_INTLEVEL3_VECTOR_VADDR
+#define INTLEVEL4_VECTOR_VADDR XCHAL_INTLEVEL4_VECTOR_VADDR
+#define INTLEVEL5_VECTOR_VADDR XCHAL_INTLEVEL5_VECTOR_VADDR
+#define INTLEVEL6_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR
+#define DEBUG_VECTOR_VADDR XCHAL_DEBUG_VECTOR_VADDR
+
+#endif
+
+#endif /* _XTENSA_VECTORS_H */
extra-y := head.o vmlinux.lds
-obj-y := align.o entry.o irq.o coprocessor.o process.o ptrace.o \
- setup.o signal.o syscall.o time.o traps.o vectors.o platform.o \
- pci-dma.o
+obj-y := align.o coprocessor.o entry.o irq.o pci-dma.o platform.o process.o \
+ ptrace.o setup.o signal.o stacktrace.o syscall.o time.o traps.o \
+ vectors.o
obj-$(CONFIG_KGDB) += xtensa-stub.o
obj-$(CONFIG_PCI) += pci.o
obj-$(CONFIG_MODULES) += xtensa_ksyms.o module.o
+AFLAGS_head.o += -mtext-section-literals
+
# In the Xtensa architecture, assembly generates literals which must always
# precede the L32R instruction with a relative offset less than 256 kB.
# Therefore, the .text and .literal section must be combined in parenthesis
* so we can allow exceptions and interrupts (*) again.
* Set PS(EXCM = 0, UM = 0, RING = 0, OWB = 0, WOE = 1, INTLEVEL = X)
*
- * (*) We only allow interrupts of higher priority than current IRQ
+ * (*) We only allow interrupts if they were previously enabled and
+ * we're not handling an IRQ
*/
rsr a3, ps
- addi a0, a0, -4
- movi a2, 1
+ addi a0, a0, -EXCCAUSE_LEVEL1_INTERRUPT
+ movi a2, LOCKLEVEL
extui a3, a3, PS_INTLEVEL_SHIFT, PS_INTLEVEL_WIDTH
# a3 = PS.INTLEVEL
- movnez a2, a3, a3 # a2 = 1: level-1, > 1: high priority
- moveqz a3, a2, a0 # a3 = IRQ level iff interrupt
+ moveqz a3, a2, a0 # a3 = LOCKLEVEL iff interrupt
movi a2, 1 << PS_WOE_BIT
or a3, a3, a2
rsr a0, exccause
save_xtregs_opt a1 a2 a4 a5 a6 a7 PT_XTREGS_OPT
+#ifdef CONFIG_TRACE_IRQFLAGS
+ l32i a4, a1, PT_DEPC
+ /* Double exception means we came here with an exception
+ * while PS.EXCM was set, i.e. interrupts disabled.
+ */
+ bgeui a4, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f
+ l32i a4, a1, PT_EXCCAUSE
+ bnei a4, EXCCAUSE_LEVEL1_INTERRUPT, 1f
+ /* We came here with an interrupt means interrupts were enabled
+ * and we've just disabled them.
+ */
+ movi a4, trace_hardirqs_off
+ callx4 a4
+1:
+#endif
+
/* Go to second-level dispatcher. Set up parameters to pass to the
* exception handler and call the exception handler.
*/
.global common_exception_return
common_exception_return:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ l32i a4, a1, PT_DEPC
+ /* Double exception means we came here with an exception
+ * while PS.EXCM was set, i.e. interrupts disabled.
+ */
+ bgeui a4, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f
+ l32i a4, a1, PT_EXCCAUSE
+ bnei a4, EXCCAUSE_LEVEL1_INTERRUPT, 1f
+ /* We came here with an interrupt means interrupts were enabled
+ * and we'll reenable them on return.
+ */
+ movi a4, trace_hardirqs_on
+ callx4 a4
+1:
+#endif
+
/* Jump if we are returning from kernel exceptions. */
1: l32i a3, a1, PT_PS
_bbci.l a3, PS_UM_BIT, 4f
+ rsil a2, 0
+
/* Specific to a user exception exit:
* We need to check some flags for signal handling and rescheduling,
* and have to restore WB and WS, extra states, and all registers
l32i a0, a1, PT_DEPC
l32i a3, a1, PT_AREG3
- _bltui a0, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f
-
- wsr a0, depc
l32i a2, a1, PT_AREG2
- l32i a0, a1, PT_AREG0
- l32i a1, a1, PT_AREG1
- rfde
+ _bgeui a0, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f
-1:
/* Restore a0...a3 and return */
- rsr a0, ps
- extui a2, a0, PS_INTLEVEL_SHIFT, PS_INTLEVEL_WIDTH
- movi a0, 2f
- slli a2, a2, 4
- add a0, a2, a0
- l32i a2, a1, PT_AREG2
- jx a0
-
- .macro irq_exit_level level
- .align 16
- .if XCHAL_EXCM_LEVEL >= \level
- l32i a0, a1, PT_PC
- wsr a0, epc\level
l32i a0, a1, PT_AREG0
l32i a1, a1, PT_AREG1
- rfi \level
- .endif
- .endm
+ rfe
- .align 16
-2:
+1: wsr a0, depc
l32i a0, a1, PT_AREG0
l32i a1, a1, PT_AREG1
- rfe
-
- .align 16
- /* no rfi for level-1 irq, handled by rfe above*/
- nop
-
- irq_exit_level 2
- irq_exit_level 3
- irq_exit_level 4
- irq_exit_level 5
- irq_exit_level 6
+ rfde
ENDPROC(kernel_exception)
*/
__HEAD
+ .begin no-absolute-literals
+
ENTRY(_start)
- _j 2f
+ /* Preserve the pointer to the boot parameter list in EXCSAVE_1 */
+ wsr a2, excsave1
+ _j _SetupMMU
+
+ .align 4
+ .literal_position
+.Lstartup:
+ .word _startup
+
.align 4
-1: .word _startup
-2: l32r a0, 1b
+ .global _SetupMMU
+_SetupMMU:
+ Offset = _SetupMMU - _start
+
+#ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
+ initialize_mmu
+#endif
+ .end no-absolute-literals
+
+ l32r a0, .Lstartup
jx a0
ENDPROC(_start)
- .section .init.text, "ax"
+ __INIT
+ .literal_position
ENTRY(_startup)
movi a0, LOCKLEVEL
wsr a0, ps
- /* Preserve the pointer to the boot parameter list in EXCSAVE_1 */
-
- wsr a2, excsave1
-
/* Start with a fresh windowbase and windowstart. */
movi a1, 1
/* Clear debugging registers. */
#if XCHAL_HAVE_DEBUG
+#if XCHAL_NUM_IBREAK > 0
wsr a0, ibreakenable
+#endif
wsr a0, icount
movi a1, 15
wsr a0, icountlevel
isync
- initialize_mmu
-
/* Unpack data sections
*
* The linker script used to build the Linux kernel image
___flush_dcache_all a2 a3
#endif
+ memw
+ isync
+ ___invalidate_icache_all a2 a3
+ isync
/* Setup stack and enable window exceptions (keep irqs disabled) */
_F(void, idle, (void), { __asm__ __volatile__ ("waiti 0" ::: "memory"); });
_F(void, heartbeat, (void), { });
_F(int, pcibios_fixup, (void), { return 0; });
+_F(void, pcibios_init, (void), { });
#ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT
_F(void, calibrate_ccount, (void),
--- /dev/null
+/*
+ * arch/xtensa/kernel/stacktrace.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001 - 2013 Tensilica Inc.
+ */
+#include <linux/export.h>
+#include <linux/sched.h>
+#include <linux/stacktrace.h>
+
+#include <asm/stacktrace.h>
+#include <asm/traps.h>
+
+void walk_stackframe(unsigned long *sp,
+ int (*fn)(struct stackframe *frame, void *data),
+ void *data)
+{
+ unsigned long a0, a1;
+ unsigned long sp_end;
+
+ a1 = (unsigned long)sp;
+ sp_end = ALIGN(a1, THREAD_SIZE);
+
+ spill_registers();
+
+ while (a1 < sp_end) {
+ struct stackframe frame;
+
+ sp = (unsigned long *)a1;
+
+ a0 = *(sp - 4);
+ a1 = *(sp - 3);
+
+ if (a1 <= (unsigned long)sp)
+ break;
+
+ frame.pc = MAKE_PC_FROM_RA(a0, a1);
+ frame.sp = a1;
+
+ if (fn(&frame, data))
+ return;
+ }
+}
+
+#ifdef CONFIG_STACKTRACE
+
+struct stack_trace_data {
+ struct stack_trace *trace;
+ unsigned skip;
+};
+
+static int stack_trace_cb(struct stackframe *frame, void *data)
+{
+ struct stack_trace_data *trace_data = data;
+ struct stack_trace *trace = trace_data->trace;
+
+ if (trace_data->skip) {
+ --trace_data->skip;
+ return 0;
+ }
+ if (!kernel_text_address(frame->pc))
+ return 0;
+
+ trace->entries[trace->nr_entries++] = frame->pc;
+ return trace->nr_entries >= trace->max_entries;
+}
+
+void save_stack_trace_tsk(struct task_struct *task, struct stack_trace *trace)
+{
+ struct stack_trace_data trace_data = {
+ .trace = trace,
+ .skip = trace->skip,
+ };
+ walk_stackframe(stack_pointer(task), stack_trace_cb, &trace_data);
+}
+EXPORT_SYMBOL_GPL(save_stack_trace_tsk);
+
+void save_stack_trace(struct stack_trace *trace)
+{
+ save_stack_trace_tsk(current, trace);
+}
+EXPORT_SYMBOL_GPL(save_stack_trace);
+
+#endif
+
+#ifdef CONFIG_FRAME_POINTER
+
+struct return_addr_data {
+ unsigned long addr;
+ unsigned skip;
+};
+
+static int return_address_cb(struct stackframe *frame, void *data)
+{
+ struct return_addr_data *r = data;
+
+ if (r->skip) {
+ --r->skip;
+ return 0;
+ }
+ if (!kernel_text_address(frame->pc))
+ return 0;
+ r->addr = frame->pc;
+ return 1;
+}
+
+unsigned long return_address(unsigned level)
+{
+ struct return_addr_data r = {
+ .skip = level + 1,
+ };
+ walk_stackframe(stack_pointer(NULL), return_address_cb, &r);
+ return r.addr;
+}
+EXPORT_SYMBOL(return_address);
+
+#endif
*
* Essentially rewritten for the Xtensa architecture port.
*
- * Copyright (C) 2001 - 2005 Tensilica Inc.
+ * Copyright (C) 2001 - 2013 Tensilica Inc.
*
* Joe Taylor <joe@tensilica.com, joetylr@yahoo.com>
* Chris Zankel <chris@zankel.net>
#include <linux/delay.h>
#include <linux/hardirq.h>
+#include <asm/stacktrace.h>
#include <asm/ptrace.h>
#include <asm/timex.h>
#include <asm/uaccess.h>
/*
* IRQ handler.
- * PS.INTLEVEL is the current IRQ priority level.
*/
extern void do_IRQ(int, struct pt_regs *);
XCHAL_INTLEVEL6_MASK,
XCHAL_INTLEVEL7_MASK,
};
- unsigned level = get_sr(ps) & PS_INTLEVEL_MASK;
-
- if (WARN_ON_ONCE(level >= ARRAY_SIZE(int_level_mask)))
- return;
for (;;) {
unsigned intread = get_sr(interrupt);
unsigned intenable = get_sr(intenable);
- unsigned int_at_level = intread & intenable &
- int_level_mask[level];
+ unsigned int_at_level = intread & intenable;
+ unsigned level;
+
+ for (level = LOCKLEVEL; level > 0; --level) {
+ if (int_at_level & int_level_mask[level]) {
+ int_at_level &= int_level_mask[level];
+ break;
+ }
+ }
- if (!int_at_level)
+ if (level == 0)
return;
/*
regs->syscall);
}
-static __always_inline unsigned long *stack_pointer(struct task_struct *task)
+static int show_trace_cb(struct stackframe *frame, void *data)
{
- unsigned long *sp;
-
- if (!task || task == current)
- __asm__ __volatile__ ("mov %0, a1\n" : "=a"(sp));
- else
- sp = (unsigned long *)task->thread.sp;
-
- return sp;
+ if (kernel_text_address(frame->pc)) {
+ printk(" [<%08lx>] ", frame->pc);
+ print_symbol("%s\n", frame->pc);
+ }
+ return 0;
}
void show_trace(struct task_struct *task, unsigned long *sp)
{
- unsigned long a0, a1, pc;
- unsigned long sp_start, sp_end;
-
- if (sp)
- a1 = (unsigned long)sp;
- else
- a1 = (unsigned long)stack_pointer(task);
-
- sp_start = a1 & ~(THREAD_SIZE-1);
- sp_end = sp_start + THREAD_SIZE;
+ if (!sp)
+ sp = stack_pointer(task);
printk("Call Trace:");
#ifdef CONFIG_KALLSYMS
printk("\n");
#endif
- spill_registers();
-
- while (a1 > sp_start && a1 < sp_end) {
- sp = (unsigned long*)a1;
-
- a0 = *(sp - 4);
- a1 = *(sp - 3);
-
- if (a1 <= (unsigned long) sp)
- break;
-
- pc = MAKE_PC_FROM_RA(a0, a1);
-
- if (kernel_text_address(pc)) {
- printk(" [<%08lx>] ", pc);
- print_symbol("%s\n", pc);
- }
- }
+ walk_stackframe(sp, show_trace_cb, NULL);
printk("\n");
}
#include <asm/processor.h>
#include <asm/page.h>
#include <asm/thread_info.h>
+#include <asm/vectors.h>
#define WINDOW_VECTORS_SIZE 0x180
xsr a0, depc # get DEPC, save a0
- movi a3, XCHAL_WINDOW_VECTORS_VADDR
+ movi a3, WINDOW_VECTORS_VADDR
_bltu a0, a3, .Lfixup
addi a3, a3, WINDOW_VECTORS_SIZE
_bgeu a0, a3, .Lfixup
.if XCHAL_EXCM_LEVEL >= \level
.section .Level\level\()InterruptVector.text, "ax"
ENTRY(_Level\level\()InterruptVector)
- wsr a0, epc1
+ wsr a0, excsave2
rsr a0, epc\level
- xsr a0, epc1
+ wsr a0, epc1
+ movi a0, EXCCAUSE_LEVEL1_INTERRUPT
+ wsr a0, exccause
+ rsr a0, eps\level
# branch to user or kernel vector
j _SimulateUserKernelVectorException
.endif
*/
.align 4
_SimulateUserKernelVectorException:
- wsr a0, excsave2
- movi a0, 4 # LEVEL1_INTERRUPT cause
- wsr a0, exccause
- rsr a0, ps
+ addi a0, a0, (1 << PS_EXCM_BIT)
+ wsr a0, ps
bbsi.l a0, PS_UM_BIT, 1f # branch if user mode
rsr a0, excsave2 # restore a0
j _KernelExceptionVector # simulate kernel vector exception
#include <asm/page.h>
#include <asm/thread_info.h>
+#include <asm/vectors.h>
#include <variant/core.h>
#include <platform/hardware.h>
OUTPUT_ARCH(xtensa)
#endif
#ifndef KERNELOFFSET
-#define KERNELOFFSET 0xd0001000
+#define KERNELOFFSET 0xd0003000
#endif
/* Note: In the following macros, it would be nice to specify only the
SECTION_VECTOR (_WindowVectors_text,
.WindowVectors.text,
- XCHAL_WINDOW_VECTORS_VADDR, 4,
+ WINDOW_VECTORS_VADDR, 4,
.dummy)
SECTION_VECTOR (_DebugInterruptVector_literal,
.DebugInterruptVector.literal,
- XCHAL_DEBUG_VECTOR_VADDR - 4,
+ DEBUG_VECTOR_VADDR - 4,
SIZEOF(.WindowVectors.text),
.WindowVectors.text)
SECTION_VECTOR (_DebugInterruptVector_text,
.DebugInterruptVector.text,
- XCHAL_DEBUG_VECTOR_VADDR,
+ DEBUG_VECTOR_VADDR,
4,
.DebugInterruptVector.literal)
#undef LAST
#if XCHAL_EXCM_LEVEL >= 2
SECTION_VECTOR (_Level2InterruptVector_text,
.Level2InterruptVector.text,
- XCHAL_INTLEVEL2_VECTOR_VADDR,
+ INTLEVEL2_VECTOR_VADDR,
SIZEOF(LAST), LAST)
# undef LAST
# define LAST .Level2InterruptVector.text
#if XCHAL_EXCM_LEVEL >= 3
SECTION_VECTOR (_Level3InterruptVector_text,
.Level3InterruptVector.text,
- XCHAL_INTLEVEL3_VECTOR_VADDR,
+ INTLEVEL3_VECTOR_VADDR,
SIZEOF(LAST), LAST)
# undef LAST
# define LAST .Level3InterruptVector.text
#if XCHAL_EXCM_LEVEL >= 4
SECTION_VECTOR (_Level4InterruptVector_text,
.Level4InterruptVector.text,
- XCHAL_INTLEVEL4_VECTOR_VADDR,
+ INTLEVEL4_VECTOR_VADDR,
SIZEOF(LAST), LAST)
# undef LAST
# define LAST .Level4InterruptVector.text
#if XCHAL_EXCM_LEVEL >= 5
SECTION_VECTOR (_Level5InterruptVector_text,
.Level5InterruptVector.text,
- XCHAL_INTLEVEL5_VECTOR_VADDR,
+ INTLEVEL5_VECTOR_VADDR,
SIZEOF(LAST), LAST)
# undef LAST
# define LAST .Level5InterruptVector.text
#if XCHAL_EXCM_LEVEL >= 6
SECTION_VECTOR (_Level6InterruptVector_text,
.Level6InterruptVector.text,
- XCHAL_INTLEVEL6_VECTOR_VADDR,
+ INTLEVEL6_VECTOR_VADDR,
SIZEOF(LAST), LAST)
# undef LAST
# define LAST .Level6InterruptVector.text
#endif
SECTION_VECTOR (_KernelExceptionVector_literal,
.KernelExceptionVector.literal,
- XCHAL_KERNEL_VECTOR_VADDR - 4,
+ KERNEL_VECTOR_VADDR - 4,
SIZEOF(LAST), LAST)
#undef LAST
SECTION_VECTOR (_KernelExceptionVector_text,
.KernelExceptionVector.text,
- XCHAL_KERNEL_VECTOR_VADDR,
+ KERNEL_VECTOR_VADDR,
4,
.KernelExceptionVector.literal)
SECTION_VECTOR (_UserExceptionVector_literal,
.UserExceptionVector.literal,
- XCHAL_USER_VECTOR_VADDR - 4,
+ USER_VECTOR_VADDR - 4,
SIZEOF(.KernelExceptionVector.text),
.KernelExceptionVector.text)
SECTION_VECTOR (_UserExceptionVector_text,
.UserExceptionVector.text,
- XCHAL_USER_VECTOR_VADDR,
+ USER_VECTOR_VADDR,
4,
.UserExceptionVector.literal)
SECTION_VECTOR (_DoubleExceptionVector_literal,
.DoubleExceptionVector.literal,
- XCHAL_DOUBLEEXC_VECTOR_VADDR - 16,
+ DOUBLEEXC_VECTOR_VADDR - 16,
SIZEOF(.UserExceptionVector.text),
.UserExceptionVector.text)
SECTION_VECTOR (_DoubleExceptionVector_text,
.DoubleExceptionVector.text,
- XCHAL_DOUBLEEXC_VECTOR_VADDR,
+ DOUBLEEXC_VECTOR_VADDR,
32,
.DoubleExceptionVector.literal)
. = ALIGN(0x10);
.bootstrap : { *(.bootstrap.literal .bootstrap.text .bootstrap.data) }
- .ResetVector.text XCHAL_RESET_VECTOR_VADDR :
+ .ResetVector.text RESET_VECTOR_VADDR :
{
*(.ResetVector.text)
}
+
+ /*
+ * This is a remapped copy of the Secondary Reset Vector Code.
+ * It keeps gdb in sync with the PC after switching
+ * to the temporary mapping used while setting up
+ * the V2 MMU mappings for Linux.
+ *
+ * Only debug information about this section is put in the kernel image.
+ */
+ .SecondaryResetVector.remapped_text 0x46000000 (INFO):
+ {
+ *(.SecondaryResetVector.remapped_text)
+ }
+
+
.xt.lit : { *(.xt.lit) }
.xt.prop : { *(.xt.prop) }
EXPORT_SYMBOL(insb);
EXPORT_SYMBOL(insw);
EXPORT_SYMBOL(insl);
+
+extern long common_exception_return;
+extern long _spill_registers;
+EXPORT_SYMBOL(common_exception_return);
+EXPORT_SYMBOL(_spill_registers);
*/
void __init init_mmu(void)
{
- /* Writing zeros to the <t>TLBCFG special registers ensure
- * that valid values exist in the register. For existing
- * PGSZID<w> fields, zero selects the first element of the
- * page-size array. For nonexistent PGSZID<w> fields, zero is
- * the best value to write. Also, when changing PGSZID<w>
+#if !(XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY)
+ /*
+ * Writing zeros to the instruction and data TLBCFG special
+ * registers ensure that valid values exist in the register.
+ *
+ * For existing PGSZID<w> fields, zero selects the first element
+ * of the page-size array. For nonexistent PGSZID<w> fields,
+ * zero is the best value to write. Also, when changing PGSZID<w>
* fields, the corresponding TLB must be flushed.
*/
set_itlbcfg_register(0);
set_dtlbcfg_register(0);
+#endif
flush_tlb_all();
/* Set rasid register to a known value. */
pc = MAKE_PC_FROM_RA(a0, pc);
/* Add the PC to the trace. */
- if (kernel_text_address(pc))
- oprofile_add_trace(pc);
-
+ oprofile_add_trace(pc);
if (pc == (unsigned long) &common_exception_return) {
regs = (struct pt_regs *)a1;
if (user_mode(regs)) {
static int rs_open(struct tty_struct *tty, struct file * filp)
{
tty->port = &serial_port;
- spin_lock(&timer_lock);
+ spin_lock_bh(&timer_lock);
if (tty->count == 1) {
setup_timer(&serial_timer, rs_poll,
(unsigned long)&serial_port);
mod_timer(&serial_timer, jiffies + SERIAL_TIMER_VALUE);
}
- spin_unlock(&timer_lock);
+ spin_unlock_bh(&timer_lock);
return 0;
}
static void rs_poll(unsigned long priv)
{
struct tty_port *port = (struct tty_port *)priv;
- struct timeval tv = { .tv_sec = 0, .tv_usec = 0 };
int i = 0;
unsigned char c;
spin_lock(&timer_lock);
- while (__simc(SYS_select_one, 0, XTISS_SELECT_ONE_READ, (int)&tv,0,0)){
- __simc (SYS_read, 0, (unsigned long)&c, 1, 0, 0);
+ while (simc_poll(0)) {
+ simc_read(0, &c, 1);
tty_insert_flip_char(port, c, TTY_NORMAL);
i++;
}
int len = strlen(s);
if (s != 0 && *s != 0)
- __simc (SYS_write, 1, (unsigned long)s,
- count < len ? count : len,0,0);
+ simc_write(1, s, count < len ? count : len);
}
static struct tty_driver* iss_console_device(struct console *c, int *index)
static int errno;
-static inline int __simc(int a, int b, int c, int d, int e, int f)
+static inline int __simc(int a, int b, int c, int d)
{
int ret;
register int a1 asm("a2") = a;
register int b1 asm("a3") = b;
register int c1 asm("a4") = c;
register int d1 asm("a5") = d;
- register int e1 asm("a6") = e;
- register int f1 asm("a7") = f;
__asm__ __volatile__ (
"simcall\n"
"mov %0, a2\n"
"mov %1, a3\n"
: "=a" (ret), "=a" (errno), "+r"(a1), "+r"(b1)
- : "r"(c1), "r"(d1), "r"(e1), "r"(f1)
+ : "r"(c1), "r"(d1)
: "memory");
return ret;
}
static inline int simc_open(const char *file, int flags, int mode)
{
- return __simc(SYS_open, (int) file, flags, mode, 0, 0);
+ return __simc(SYS_open, (int) file, flags, mode);
}
static inline int simc_close(int fd)
{
- return __simc(SYS_close, fd, 0, 0, 0, 0);
+ return __simc(SYS_close, fd, 0, 0);
}
static inline int simc_ioctl(int fd, int request, void *arg)
{
- return __simc(SYS_ioctl, fd, request, (int) arg, 0, 0);
+ return __simc(SYS_ioctl, fd, request, (int) arg);
}
static inline int simc_read(int fd, void *buf, size_t count)
{
- return __simc(SYS_read, fd, (int) buf, count, 0, 0);
+ return __simc(SYS_read, fd, (int) buf, count);
}
static inline int simc_write(int fd, const void *buf, size_t count)
{
- return __simc(SYS_write, fd, (int) buf, count, 0, 0);
+ return __simc(SYS_write, fd, (int) buf, count);
}
static inline int simc_poll(int fd)
{
struct timeval tv = { .tv_sec = 0, .tv_usec = 0 };
- return __simc(SYS_select_one, fd, XTISS_SELECT_ONE_READ, (int)&tv,
- 0, 0);
+ return __simc(SYS_select_one, fd, XTISS_SELECT_ONE_READ, (int)&tv);
+}
+
+static inline int simc_lseek(int fd, uint32_t off, int whence)
+{
+ return __simc(SYS_lseek, fd, off, whence);
}
#endif /* _XTENSA_PLATFORM_ISS_SIMCALL_H */
}
-#ifdef CONFIG_PCI
-void platform_pcibios_init(void)
-{
-}
-#endif
-
void platform_halt(void)
{
pr_info(" ** Called platform_halt() **\n");
"wsr a2, icountlevel\n\t"
"movi a2, 0\n\t"
"wsr a2, icount\n\t"
+#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
+#endif
"wsr a2, lcount\n\t"
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
while (nbytes > 0) {
unsigned long io;
- __simc(SYS_lseek, dev->fd, offset, SEEK_SET, 0, 0);
+ simc_lseek(dev->fd, offset, SEEK_SET);
if (write)
io = simc_write(dev->fd, buffer, nbytes);
else
err = -ENODEV;
goto out;
}
- dev->size = __simc(SYS_lseek, dev->fd, 0, SEEK_END, 0, 0);
+ dev->size = simc_lseek(dev->fd, 0, SEEK_END);
set_capacity(dev->gd, dev->size >> SECTOR_SHIFT);
dev->filename = filename;
pr_info("SIMDISK: %s=%s\n", dev->gd->disk_name, dev->filename);
"wsr a2, icountlevel\n\t"
"movi a2, 0\n\t"
"wsr a2, icount\n\t"
+#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
+#endif
"wsr a2, lcount\n\t"
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
"wsr a2, icountlevel\n\t"
"movi a2, 0\n\t"
"wsr a2, icount\n\t"
+#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
+#endif
"wsr a2, lcount\n\t"
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
projects / karo-tx-linux.git / commitdiff