1 <!-- Copyright (C) 2003 Red Hat, Inc. -->
2 <!-- This material may be distributed only subject to the terms -->
3 <!-- and conditions set forth in the Open Publication License, v1.0 -->
4 <!-- or later (the latest version is presently available at -->
5 <!-- http://www.opencontent.org/openpub/). -->
6 <!-- Distribution of the work or derivative of the work in any -->
7 <!-- standard (paper) book form is prohibited unless prior -->
8 <!-- permission is obtained from the copyright holder. -->
12 >Cirrus Logic ARM CL-PS7111 Evaluation Board Hardware Setup</TITLE
13 ><meta name="MSSmartTagsPreventParsing" content="TRUE">
16 CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
19 TITLE="eCos User Guide"
20 HREF="ecos-user-guide.html"><LINK
23 HREF="appendix-target-setup.html"><LINK
25 TITLE="Cirrus Logic ARM EP7209 Development Board Hardware Setup"
26 HREF="setup-arm-ep7209.html"><LINK
28 TITLE="StrongARM EBSA-285 Hardware Setup"
29 HREF="setup-arm-ebsa285.html"></HEAD
40 SUMMARY="Header navigation table"
57 HREF="setup-arm-ep7209.html"
65 >Appendix A. Target Setup</TD
71 HREF="setup-arm-ebsa285.html"
85 NAME="SETUP-ARM-CLPS7111">Cirrus Logic ARM CL-PS7111 Evaluation Board Hardware Setup</H1
87 >The implementation of the port of eCos to the Cirrus Logic
88 ARM CL-PS7111 Evaluation Board (also known as EB7111) is based on
89 the EP7211 Development Board port.</P
91 >For that reason, the setup required is identical to the EP7211
92 Development Board as described above, with the following exceptions:</P
98 >The Cygmon ROM monitor is not supported</P
102 >The ARM Multi-ICE is not supported</P
106 >Pre-built GDB stubs are provided in the
107 directory loaders/arm-eb7111 relative to the root of your
112 >If rebuilding the GDB stub ROM image, change the "Cirrus
113 Logic processor variant" option (CYGHWR_HAL_ARM_EDB7XXX_VARIANT)
114 from the EP7211 to the CL_PS7111. This can be selected
120 >eCos Configuration Tool</I
123 , or if using ecosconfig, can be set by uncommenting the user_value
124 property of this option in ecos.ecc and setting it to "CL_PS7111"</P
128 >All remote serial communication is done with the serial I/O
137 CLASS="PROGRAMLISTING"
139 % slow_cat.tcl < [path]/gdb_module.srec > /dev/ttyS0</PRE
144 >Power off the board, and change it to boot the GDB stubs in
145 big-endian mode by setting the switches like this:</P
147 >SW1: 00000000 (all levers down)
150 >The GDB stubs allow communication with GDB using the serial
151 port at connector PJ7A (lower connector). The communication parameters
152 are fixed at 38400 baud, 8 data bits, no parity bit and 1 stop
153 bit (8-N-1). No flow control is employed. Connection to the host
154 computer should be made using a straight through serial cable.</P
161 SUMMARY="Footer navigation table"
172 HREF="setup-arm-ep7209.html"
181 HREF="ecos-user-guide.html"
190 HREF="setup-arm-ebsa285.html"
200 >Cirrus Logic ARM EP7209 Development Board Hardware Setup</TD
206 HREF="appendix-target-setup.html"
214 >StrongARM EBSA-285 Hardware Setup</TD