enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
--- /dev/null
+#
+# Makefile for siemens CORVUS (AT91SAM9G45) based board
+# (C) Copyright 2013 Siemens AG
+#
+# Based on:
+# U-Boot file: board/atmel/at91sam9m10g45ek/Makefile
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian@popies.net>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += board.o
--- /dev/null
+/*
+ * Board functions for Siemens CORVUS (AT91SAM9G45) based board
+ * (C) Copyright 2013 Siemens AG
+ *
+ * Based on:
+ * U-Boot file: board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9g45_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+#include <spi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CMD_NAND
+static void corvus_nand_hw_init(void)
+{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ unsigned long csa;
+
+ /* Enable CS3 */
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
+ writel(csa, &matrix->ebicsa);
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
+ &smc->cs[3].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_MODE_DBW_8 |
+#endif
+ AT91_SMC_MODE_TDF_CYCLE(3),
+ &smc->cs[3].mode);
+
+ writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_CMD_USB
+static void taurus_usb_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ writel(1 << ATMEL_ID_PIODE, &pmc->pcer);
+
+ at91_set_gpio_output(AT91_PIN_PD1, 0);
+ at91_set_gpio_output(AT91_PIN_PD3, 0);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void corvus_macb_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ /* Enable clock */
+ writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
+
+ /*
+ * Disable pull-up on:
+ * RXDV (PA15) => PHY normal mode (not Test mode)
+ * ERX0 (PA12) => PHY ADDR0
+ * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
+ *
+ * PHY has internal pull-down
+ */
+ at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTA, 12, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTA, 13, 0);
+
+ at91_phy_reset();
+
+ /* Re-enable pull-up */
+ at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1);
+
+ /* And the pins. */
+ at91_macb_hw_init();
+}
+#endif
+
+int board_early_init_f(void)
+{
+ at91_seriald_hw_init();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_CMD_NAND
+ corvus_nand_hw_init();
+#endif
+#ifdef CONFIG_ATMEL_SPI
+ at91_spi0_hw_init(1 << 4);
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_spi0_hw_init(1 << 0);
+#endif
+#ifdef CONFIG_MACB
+ corvus_macb_hw_init();
+#endif
+#ifdef CONFIG_CMD_USB
+ taurus_usb_hw_init();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
+
+/* SPI chip select control */
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ return bus == 0 && cs < 2;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ switch (slave->cs) {
+ case 1:
+ at91_set_gpio_output(AT91_PIN_PB18, 0);
+ break;
+ case 0:
+ default:
+ at91_set_gpio_output(AT91_PIN_PB3, 0);
+ break;
+ }
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ switch (slave->cs) {
+ case 1:
+ at91_set_gpio_output(AT91_PIN_PB18, 1);
+ break;
+ case 0:
+ default:
+ at91_set_gpio_output(AT91_PIN_PB3, 1);
+ break;
+ }
+}
Active arm arm926ejs at91 taskit stamp9g20 portuxg20 stamp9g20:AT91SAM9G20,PORTUXG20 Markus Hubig <mhubig@imko.de>
Active arm arm926ejs at91 taskit stamp9g20 stamp9g20 stamp9g20:AT91SAM9G20 Markus Hubig <mhubig@imko.de>
Active arm arm926ejs at91 siemens taurus axm taurus:AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM Heiko Schocher <hs@denx.de>
+Active arm arm926ejs at91 siemens corvus corvus corvus:AT91SAM9M10G45,SYS_USE_NANDFLASH Heiko Schocher <hs@denx.de>
Active arm arm926ejs at91 siemens taurus taurus taurus:AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS Heiko Schocher <hs@denx.de>
Active arm arm926ejs davinci ait cam_enc_4xx cam_enc_4xx cam_enc_4xx Heiko Schocher <hs@denx.de>
Active arm arm926ejs davinci Barix ipam390 ipam390 - Heiko Schocher <hs@denx.de>
--- /dev/null
+/*
+ * Common board functions for siemens AT91SAM9G45 based boards
+ * (C) Copyright 2013 Siemens AG
+ *
+ * Based on:
+ * U-Boot file: include/configs/at91sam9m10g45ek.h
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/hardware.h>
+
+#define MACH_TYPE_CORVUS 2066
+
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires
+ * adapting the initial boot program.
+ * Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+
+#define CONFIG_SYS_TEXT_BASE 0x73f00000
+
+#define CONFIG_AT91_LEGACY
+#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_AT91FAMILY
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED AT91_PIN_PD31 /* this is the user1 led */
+#define CONFIG_GREEN_LED AT91_PIN_PD0 /* this is the user2 led */
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6
+#define CONFIG_SYS_SDRAM_SIZE 0x08000000
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+/* No NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8
+
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_AT91_WANTS_COMMON_PHY
+
+/* USB */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_USB_STORAGE
+
+#define CONFIG_SYS_LOAD_ADDR 0x72000000 /* load address */
+
+/* bootstrap + u-boot + env in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x100000
+#define CONFIG_ENV_OFFSET_REDUND 0x180000
+#define CONFIG_ENV_SIZE 0x20000
+
+#define CONFIG_BOOTCOMMAND \
+ "nand read 0x70000000 0x200000 0x300000;" \
+ "bootm 0x70000000"
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 earlyprintk " \
+ "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
+ "256k(env),256k(env_redundant),256k(spare)," \
+ "512k(dtb),6M(kernel)ro,-(rootfs) " \
+ "root=/dev/mtdblock7 rw rootfstype=jffs2"
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_PROMPT "U-Boot> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \
+ 128*1024, 0x1000)
+
+#endif
projects / karo-tx-uboot.git / commitdiff