Merge tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8, take 2" from Maxime Ripard:
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
* tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (21 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: sun7i: bananapi-m1-plus: red LED is power LED
ARM: dts: sun7i: bananapi-m1-plus: Unify suffix for board specific labels
ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
ARM: dts: sun7i: lamobo-r1: Enable audio codec
ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
...
Hans de Goede [Fri, 8 Jul 2016 16:05:56 +0000 (18:05 +0200)]
ARM: dts: sun8i: Add dts file for inet86dz board
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 8 Jul 2016 16:05:55 +0000 (18:05 +0200)]
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 8 Jul 2016 16:05:43 +0000 (18:05 +0200)]
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.
Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.
Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property
i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.
Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a
reg property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg
property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Endpoint nodes have a reg property. Add their mandatory unit-address.
This solves:
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep0 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep1 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep2 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep4 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep5 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep6 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep7 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep8 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep9 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep10 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep11 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep12 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep13 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep14 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep15 has a reg or ranges property, but no unit name
The triggers don't need a reg property, remove it when prenset. Also remove
the unit-address from their name.
This solves:
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@3 has a unit name, but no reg property
Sergei Shtylyov [Mon, 11 Jul 2016 21:52:43 +0000 (00:52 +0300)]
ARM: dts: r8a7792: remove ADSP clock
Simon Horman told me that R8A7792 has ADSP clock based on an incorrect
table in the most recent R-Car gen2 manual. But when I received that manual
I discovered that this is false: R8A7792 is the only Gen 2 SoC that doesn't
have ADSP at all. Accordingly remove the ADSP clock from DT for the
r8a7792.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Mon, 11 Jul 2016 21:51:58 +0000 (00:51 +0300)]
ARM: dts: r8a7792: add PLL1 divided by 2 clock
Despite the fact that QSPI clock has PLL1/VCOx1/4 clock as a parent, the
latter hasn't been added to the R8A7792 device tree. This patch corrects
that oversight.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge tag 'sti-late-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/late
Merge "STi late updates for v4.8" from Patrice Chotard:
- Add STi DT critical clocks declaration
- Remove SPI hack wich has dependecy with critical clocks
These 2 STi DT patches and SPI hack MUST be applied after patches
contained into Stephen Boyd's branch clk-next/clk-st-critical.
This to ensure not to break SPI.
Merging this in avoids a build error that was missed earlier:
In file included from ../arch/arm/boot/dts/meson8b-mxq.dts:48:0:
../arch/arm/boot/dts/meson8b.dtsi:49:53: fatal error: dt-bindings/reset/amlogic,meson8b-reset.h: No such file or directory
* reset/for-4.8-2:
dt-bindings: reset: Add bindings for the Meson SoC Reset Controller
reset: Add support for the Amlogic Meson SoC Reset Controller
reset: Return -ENOTSUPP when not configured
reset: oxnas: Use devm register API and get rid of platform remove
reset: fix Kconfig menu to include reset drivers in sub-menu
reset: zynq: use devm_reset_controller_register()
reset: socfpga: use devm_reset_controller_register()
reset: sunxi: use devm_reset_controller_register()
reset: pistachio: use devm_reset_controller_register()
reset: ath79: use devm_reset_controller_register()
reset: add devm_reset_controller_register API
Merge tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v4.8-rc1" from Thierry Reding:
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
* tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Initial support for Apalis TK1
ARM: tegra: Remove commas from unit addresses on Tegra124
ARM: tegra: Import latest Jetson TK1 spreadsheet
ARM: tegra: Add spaces around = in properties
ARM: tegra: Fix a couple of DTC warnings
Lee Jones [Tue, 7 Jun 2016 11:19:00 +0000 (13:19 +0200)]
spi: st-ssc4: Remove 'no clocking' hack
Due to the newly upstreamed 'critical clocks' API we can now
safely handle clocking in the SPI and I2C drivers without fear
of catastrophically crippling the running platform.
Lots of platforms contain clocks which if turned off would prove fatal.
The only way to recover is to restart the board(s). This driver takes
references to clocks which are required to be always-on. The Common
Clk Framework will then take references to them. This way they will
not be turned off during the clk_disabled_unused() procedure.
In this patch we are identifying clocks, which if gated would render
the STiH410 development board unserviceable.
The clearfog DTS should not be defining the on-board phy, this device
is located on the microsom. Remove the duplicated definition.
Reported-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Marcel Ziswiler [Wed, 29 Jun 2016 22:23:17 +0000 (00:23 +0200)]
ARM: tegra: Initial support for Apalis TK1
This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.
The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
Please keep the remaining 0, notation on the GPU node in place as a
former mainline U-Boot version was looking for that particular notation
in order to perform required fix-ups on it.
Stephen Warren [Tue, 21 Jun 2016 18:51:49 +0000 (12:51 -0600)]
ARM: tegra: Import latest Jetson TK1 spreadsheet
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.
The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 10 Jun 2016 16:55:24 +0000 (18:55 +0200)]
ARM: tegra: Add spaces around = in properties
This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.
Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olof Johansson [Fri, 8 Jul 2016 03:39:01 +0000 (20:39 -0700)]
Merge tag 'pxa-dt-4.7' of https://github.com/rjarzmik/linux into next/dt
This device-tree pxa update brings :
- pin control nodes for pxa2xx and pxa3xx
- the LCD controller for pxa2xx
- the missing pxa3xx pulse width modulator nodes
- an USB Host fix for pxa3xx
* tag 'pxa-dt-4.7' of https://github.com/rjarzmik/linux:
ARM: dts: pxa3xx: add pincontrol helpers
ARM: dts: pxa: add pinctrl to pxa3xx
ARM: dts: pxa: fix the ohci clock for pxa3xx
ARM: dts: add pincontroller to pxa27x
ARM: dts: pxa: add pxa3xx pwm nodes
ARM: dts: pxa: add pxa framebuffer device
Merge tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux into next/dt
Merge "additional Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
* tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Specify RAM amount for BCM958625HR board
ARM: BCM5301X: Fix NAND ECC parameters for D-Link DIR-885L
ARM: BCM5301X: Specify NAND chip select and ECC in separated files
ARM: dts: Cygnus: Add Broadcom iproc-static-adc DT node
ARM: dts: BCM5301x: Add BCM953012ER board
ARM: dts: BCM5301x: Add RNG Device Tree node
ARM: bcm2835: dt: Add the ethernet to the device trees
Merge tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi into next/dt
Merge "ARM: DT: Hisilicon ARMv7 SoC Hi3519 DT updates for 4.8" from Wei Xu:
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
* tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi:
ARM: dts: add dts files for Hi3519 and tidy up the makefile entries
ARM: dt-bindings: add device tree bindings for Hi3519 sysctrl
Merge tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8" from Maxime Ripard:
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
* tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (54 commits)
ARM: dts: sun5i: Enable otg on the auxtex t004
ARM: sun5i: Allow PLL3 2x fixed factor clock to change PLL3 rate
ARM: sun7i: Add DAI nodes
ARM: sun7i: Add mod1 clock nodes
ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
ARM: dts: sun5i: Add axp152 pmic node to mk802
ARM: dts: sun5i: Enable otg on the mk802
ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
ARM: sun8i: Add Parrot Board DTS
ARM: dts: sun5i: q8-common: Enable USB-based WiFi
ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board
ARM: dts: sun8i-q8-common: Add support for USB wifi controllers
ARM: dts: sun9i: a80-optimus: Order nodes by alphabetical order
ARM: dts: sun9i: cubieboard4: Order nodes by alphabetical order
ARM: dts: sun7i: Add NFC node to Allwinner A20 SoC
ARM: dts: sun4i: Add NFC node to Allwinner A10 SoC
ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
ARM: dts: sun6i: The blue led on the Mele M9 is a power led
ARM: dts: sun6i: The blue led on the Mele A1000G quad is a power led
...
- Fix the I2C address and supply line names for the AK8974
- Sets up the interrupt lines to the different components as they
actually are connected, I was confused for some time by the fact
that several lines were connected with <NM> 0 Ohm resistors, which
means NOT MOUNTED and is thus not 0 Ohm at all but infinite ohms,
i.e. not connected at all.
Olof Johansson [Thu, 7 Jul 2016 05:33:05 +0000 (22:33 -0700)]
Merge tag 'tegra-for-4.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: tegra: Updates for v4.8-rc1
A couple of fixes for the Tegra XUSB controller and Tegra XUSB pad
controller bindings, as well as the addition of some compatible strings
for Tegra-based boards.
* tag 'tegra-for-4.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra: Add Apalis TK1 device tree binding documentation
dt-bindings: tegra: Add Colibri T30 device tree binding documentation
dt-bindings: usb: Fix Tegra XUSB example
dt-bindings: phy: Fix description of Tegra210 PHY nodes
Olof Johansson [Thu, 7 Jul 2016 05:22:19 +0000 (22:22 -0700)]
Merge tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Audio support and spi-flash on rk3288-veyron Chromedevices
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
* tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add support rk3229 evb board
ARM: dts: rockchip: add GMAC nodes for RK322x SoCs
ARM: dts: rockchip: add i2s nodes for RK322x SoCs
ARM: dts: rockchip: rename rk3228.dtsi to rk322x.dtsi
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
ARM: dts: rockchip: rename i2s model for Veyron devices
ARM: dts: rockchip: move rk3288 io-domain nodes to the grf
ARM: dts: rockchip: Enable analog audio on rk3288-veyron chromebooks
ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards
ARM: dts: rockchip: add SPI flash node for rk3288-veyron
Olof Johansson [Thu, 7 Jul 2016 05:11:20 +0000 (22:11 -0700)]
Merge tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.8
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
* tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (41 commits)
ARM: dts: r8a7792: add SMP support
ARM: dts: r8a7793: Add APMU node and second CPU core
ARM: dts: r8a7791: Add APMU node
ARM: dts: r8a7790: Add APMU nodes
devicetree: bindings: Renesas APMU and SMP Enable method
ARM: dts: kzm9g: Update console parameters
ARM: dts: kzm9d: Update console parameters
ARM: dts: marzen: Add serial port config to chosen/stdout-path
ARM: dts: genmai: Update console parameters
ARM: dts: armadillo800eva: Update console parameters
ARM: dts: r8a7792: add JPU support
ARM: dts: r8a7792: add JPU clocks
ARM: dts: silk: add DU pins
ARM: dts: blanche: add Ethernet support
ARM: dts: blanche: initial device tree
ARM: dts: blanche: document Blanche board
ARM: dts: r8a7792: add IRQC support
ARM: dts: r8a7792: add [H]SCIF support
ARM: dts: r8a7792: add SYS-DMAC support
ARM: dts: r8a7792: initial SoC device tree
...
Olof Johansson [Wed, 6 Jul 2016 05:46:39 +0000 (22:46 -0700)]
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Olof Johansson [Wed, 6 Jul 2016 05:33:16 +0000 (22:33 -0700)]
Merge tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree updates for omaps for v4.8 merge window.
This is a series of dtc warning fixes when compiled with make W=2
from Javier Martinez Canillas <javier@osg.samsung.com>.
* tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: dts: am57xx: sbc-am57x: remove unneded unit name
ARM: dts: omap5-board-common: remove unneded unit names
ARM: dts: omap5-cm-t54: remove unneded unit names and add reg properties
ARM: dts: am437x: cm-t43: remove unneded unit names
ARM: dts: am437x-gp-evm: remove unneded unit name
ARM: dts: am43xx-epos-evm: remove unneded unit name
ARM: dts: omap4-var-om44customboard: remove unneded unit name
ARM: dts: omap4-sdp: remove unneded unit names
ARM: dts: omap4-panda-common: remove unneded unit names
ARM: dts: omap4-duovero-parlor: remove unneded unit name
ARM: dts: omap3-thunder: remove unneded unit name
ARM: dts: sbc-t3x30: remove unneded unit names
ARM: dts: omap3-pandora-common: remove unneded unit name
ARM: dts: omap3-overo-common-dvi: remove unneded unit names
ARM: dts: omap3-igep0020-common: remove unneded unit names
ARM: dts: omap3: overo: remove unneded unit names in display nodes
ARM: dts: omap3-ha-lcd: remove unneeded unit name
ARM: dts: omap3-gta04: remove unneeded unit names
ARM: dts: omap3-devkit8000-lcd-common: remove unneeded unit names
ARM: dts: omap3-devkit8000: remove unneeded unit names
...
Olof Johansson [Wed, 6 Jul 2016 04:00:05 +0000 (21:00 -0700)]
Merge tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree update for 4.8:
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
* tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D support
ARM: dts: imx7d: move input header into base device tree
ARM: dts: imx7d: recreate imx7d.dtsi with i.MX 7Dual specifics
ARM: dts: imx7d: use imx7s.dtsi as base device tree
ARM: dts: imx7d-sdb: Add support for touchscreen
ARM: dts: imx7d-sdb: Add display support
ARM: dts: imx7d: Add SPI support
ARM: dts: imx6q-bx50v3: Add gpio power off support
ARM: dts: imx6ul-pico-hobbit: Fix Ethernet PHY reset GPIO
ARM: dts: imx6q-tbs2910: fix pcie reset polarity
ARM: dts: imx6sx-sdb: Use WDOG_B pin reset
ARM: dts: imx6ul-evk: Use WDOG_B pin reset
ARM: dts: imx7d-sdb: Use WDOG_B pin reset
ARM: dts: imx6qdl-sabresd: Use WDOG_B pin reset
ARM: dts: utilite-pro: add mmc card slot support
ARM: dts: imx6q-cm-fx6: fix the operation points
ARM: dts: imx6qdl.dtsi: add "arm,shared-override" for pl310
ARM: imx25-pinfunc: remove SION from all modes
ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
ARM: dts: ls1021a: Add dis_rxdet_inp3_quirk property to USB3 node
...
Hans de Goede [Wed, 29 Jun 2016 18:46:59 +0000 (20:46 +0200)]
ARM: dts: sun5i: Enable otg on the auxtex t004
The auxtek t004 has its otg usb vbus hardwired to 5v (likely in case
people use it to power the board instead of the dedicated power micro
usb connector), it does have an id pin, so it allows full otg
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olof Johansson [Tue, 5 Jul 2016 05:38:25 +0000 (22:38 -0700)]
Merge tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm Device Tree Changes for v4.8
* Reverse BAM dma node reverts
* Add BAM remote control options for affected platforms
* Enable peripherals on APQ8074 dragonboard
* Enable PMA8084 pwrky
* Fix PMIC reg entries by removing unnecessary size element
* Add SCM binding and support for all currently supported boards
* Add Qualcomm WCNSS binding documentation
* Rename db600c to SD_600eval and add peripheral nodes
* Remove gpio key entry from Nexus7
* Add APQ8060 based dragonboard and associated peripherals
* Add ARMv7 PMU for IPQ4019
* Update smem state cells to match documentation
* tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (26 commits)
dts: ipq4019: support ARMv7 PMU
ARM: dts: add Qualcomm APQ8060-based Dragonboard
ARM: dts: move the fixed MMC regulator to SURF board
ARM: dts: fix the MSM8660 RTC base address
ARM: dts: add I2C block in GSBI12
ARM: dts: add L2CC and RPM with regulators for MSM8660
ARM: dts: add SDCC5 to Qualcomm MSM8660
ARM: dts: add GPIO and MPP to MSM8660 PMIC
device-tree: nexus7: Remove power gpio key entry and use pmic8xxx-pwrkey
arm: dts: qcom: Update smem state cells usage
ARM: dts: qcom: msm8974-honami: Set DMA as remotely controlled
ARM: dts: sd_600eval: Fix eMMC lockup issue
ARM: dts: apq8064: rename db600c to SD_600eval
ARM: dts: apq8064: move sdcc3 pinctrls out of baord file
ARM: dts: apq8064: move sdcc1 pinctrl nodes to soc file
dt: binding: Add Qualcomm WCNSS control binding
dts: qcom: apq8064: Add SCM firmware node
dts: qcom: msm8974: Add SCM firmware node
dts: qcom: apq8084: Add SCM firmware node
dt/bindings: firmware: Add Qualcomm SCM binding
...
Olof Johansson [Tue, 5 Jul 2016 04:48:14 +0000 (21:48 -0700)]
Merge tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.8 merge window:
- PWM binding updates and related dts changes
- OCM RAM updates for dra7
- Enable n900 lirc-rx51 driver
- omap3-gta04 updates for backlight, bma180, itg3200, hmc5843 and wifi
- am335x, am437x and am57xx operating point updates and additions
- am335x-icev2 pca9536 node
- dra72-evm regulator updates
- edma spelling fixes
- am335x and am437x ethernet phy update
- a series of mcbsp updates
- omap3-gta04 eeprom
- dra7 PCIe unit address fix
- stdout-path for beaglebone variants
- crypto accelerator nodes for am335x, am437x and dra7
* tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: AM43xx: Add node for RNG
ARM: dts: AM43xx: clk: Add RNG clk node
ARM: dts: DRA7: Add DT node for RNG IP
ARM: dts: DRA7: Add support for SHA IP
ARM: dts: DRA7: Add DT nodes for AES IP
ARM: dts: DRA7: Add DT node for DES IP
ARM: dts: am335x-bone-common: use stdout-path in Beaglebone boards.
ARM: dts: DRA7: fix unit address of second PCIe instance
ARM: dts: omap3-gta04: Add RFID eeprom node
ARM: dts: omap4-duovero: Add pdmclk binding for audio
ARM: dts: omap4-var-som-om44: Add pdmclk binding for audio
ARM: dts: omap4-sdp: Add pdmclk binding for audio
ARM: dts: omap4-panda-common: Add pdmclk binding for audio
ARM: dts: omap5-board-common: Add pdmclk binding for audio
ARM: dts: omap3: Add clocks to McBSP nodes
ARM: dts: am335x-bone-common: Mark MAC as having only one PHY
ARM: dts: am437x-idk-evm: Mark MAC as having only one PHY
ARM: dts: Correct misspelling, "emda3" -> "edma3"
ARM: dts: dra72-evm: Rename 3.3V regulator tag
ARM: dts: am335x-icev2: Add DT node for TI PCA9536
...
Hans de Goede [Wed, 29 Jun 2016 18:47:02 +0000 (20:47 +0200)]
ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
The a10s mk802 uses a rtl8189es sdio wifi chip, add a node enabling
the mmc1 controller, this enables using the wifi chip (together with
an out of tree sdio driver for it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Florian Fainelli [Tue, 28 Jun 2016 00:45:56 +0000 (17:45 -0700)]
ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
Now that we have a proper binding for Ethernet switches hanging off
different buses, and a driver for the BCM53125 switch, add its Device
Tree as a child MDIO node, at MDIO address 30 (Broadcom pseudo-PHY
address) and describe the ports layout of the Lamobo R1 board.
Quentin Schulz [Fri, 24 Jun 2016 10:10:01 +0000 (12:10 +0200)]
ARM: sun8i: Add Parrot Board DTS
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Luo Yi [Fri, 17 Jun 2016 09:56:02 +0000 (17:56 +0800)]
ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board
Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 15 Jun 2016 18:23:50 +0000 (20:23 +0200)]
ARM: dts: sun8i-q8-common: Add support for USB wifi controllers
Some of the sun8i q8 boards have an usb wifi controller, on other
variants this will result in an used usb root-hub, but the best
way to deal with wifi on this boards is to simply let the kernel
auto-detect usb or sdio wifi controllers.
This has been tested on an a23 based q8 tablet with a RTL8188ETV wifi
controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Boris Brezillon [Tue, 14 Jun 2016 11:17:38 +0000 (14:17 +0300)]
ARM: dts: sun7i: Add NFC node to Allwinner A20 SoC
Add NAND Flash controller node definition to the A20 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Boris Brezillon [Tue, 14 Jun 2016 11:17:36 +0000 (14:17 +0300)]
ARM: dts: sun4i: Add NFC node to Allwinner A10 SoC
Add NAND Flash controller node definition to the A10 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 12 Jun 2016 11:07:01 +0000 (13:07 +0200)]
ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 12 Jun 2016 11:07:00 +0000 (13:07 +0200)]
ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 5 Jun 2016 12:23:13 +0000 (14:23 +0200)]
ARM: dts: sun6i: The blue led on the Mele M9 is a power led
The blue led on the Mele M9 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to m9:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org>
Hans de Goede [Sun, 5 Jun 2016 12:23:12 +0000 (14:23 +0200)]
ARM: dts: sun6i: The blue led on the Mele A1000G quad is a power led
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to a1000g:blue:pwr (fixing a copy
and paste error in the prefix while at it) and marks it as default on,
fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org>
Hans de Goede [Sun, 5 Jun 2016 12:23:11 +0000 (14:23 +0200)]
ARM: dts: sun4i: The blue led on the Mele A1000 is a power led
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from a1000:blue:usr to a1000:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org>
projects / karo-tx-linux.git / log